Models
>
ZGU385LSM1SS
ZGU385LSM1SS General Electric Cooktop - Overview
Sections of the ZGU385LSM1SS
[Viewing 2 of 2]
Keep searches simple, eg. "belt" or "pump".
Grate Foot
PartSelect #: PS2353327
Manufacturer #: WB02T10461
The Grate Foot is a black rubber part which attaches underneath the grate in order to protect your stovetop from being scratched, which it does by cushioning the grate on your gas range. If this part ...
$12.51
In Stock
Burner Control Knob - Stainless
PartSelect #: PS11700818
Manufacturer #: WB03X24360
Sold individually. This knob accepts a D-shaped shaft.
$65.10
In Stock
Screw
PartSelect #: PS271689
Manufacturer #: WH2X930
This screw is sold individually.
$12.22
In Stock
Orifice Spud - LP - Right Front - Simmer
PartSelect #: PS1016856
Manufacturer #: WB28T10118
$11.02
In Stock
Orifice Spud - LP - Right Front - Main
PartSelect #: PS1019740
Manufacturer #: WB28T10117
$12.14
In Stock
Questions And Answers for ZGU385LSM1SS
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the ZGU385LSM1SS
[Viewing 1 of 1]
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Grate Foot had worn out
A rubber grate foot on my range top had worn out. I pulled the worn foot out and installed the new grate foot with no tools or accessories. Good as new! Now I don't have to worry about the grate scraping my range top and scratching the paint. I also ordered extras so I won't have to wait if another wears out.
Parts Used:
-
Kathryn from Star City, AR
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
24 of 30 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Igniter on one burner wasn't working consistently
Fairly easy repair. Remove the grate, then remove the loose fitting burner assemblies. Unscrew 5 screws using Torx (star) screwdrivers - 3 along the ring top and 2 on the inside flat portion of the ring. You'll need 2 different size Torx screwdrivers. Once the screws are removed, lift that piece. It may be stuck from years of baked-o
... Read more
n spills, but there's nothing else mechanically holding it. pull off the electrical lead, which is just held with a compression fitting. Use needle-nose pliers to pull off the C-clip holding the igniter in place. Careful not to lose the little spring that the C-clip holds in place, though it's not really under a lot of tension. Change out the igniter and reassemble everything. I used the pliers to push the clip back in place. All set - works like new.
Read less
Parts Used:
-
Anthony from Orlando, FL
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
5 of 6 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
After my housecleaner had been here, I noted that 2 of the little rubber feet were missing from the top grates.
I was pretty upset as the grate wobbled, so I went on line and looked for GE Profile parts. To my amazement, I found the little rubber feet quite easily, and within 2 days they were here at my home. I simply had to stick them in the holes; however, I noted that they did not fit real tight, so I removed them and shot a little glue on the
... Read more
m, and they have been in place ever since. Thanks to you guys, I am a happy camper now!!!
Read less
Parts Used:
-
Anne from Jacksonville, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
4 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!