Models
>
WSM2780LBW
WSM2780LBW General Electric Washer Dryer Combo - Overview
Sections of the WSM2780LBW
[Viewing 6 of 6]Keep searches simple, eg. "belt" or "pump".
Rear Bearing
PartSelect #: PS267858
Manufacturer #: WE3X70
Bearing Only. This part helps your appliance run as quietly as possible.
No Longer Available
Hose Clamp Kit
PartSelect #: PS270806
Manufacturer #: WH1X2036
This is a water hose clamp kit for a variety of appliances including dishwashers and washers. This is a genuine replacement part. The kit includes two hose clamps. The smaller of the two is 1 inch in ...
$15.89
In Stock
Blower Wheel
PartSelect #: PS960003
Manufacturer #: WE16M15
This wheel attaches to the motor.
$74.16
In Stock
Igniter
PartSelect #: PS268196
Manufacturer #: WE4X750
This igniter is used for gas dryers. This part ignites the gas within the dryer.
$44.36
In Stock
DRYER BEARING BRACKET
PartSelect #: PS12710145
Manufacturer #: WE13X28680
This bracket is used on the drum bearing.
$35.08
In Stock
Control Knob
PartSelect #: PS266959
Manufacturer #: WE1X1269
This knob will accept a D-shaped shaft.
No Longer Available
Timer Knob
PartSelect #: PS266854
Manufacturer #: WE1X1151
This knob accepts a D-shaped shaft.
No Longer Available
Questions And Answers for WSM2780LBW
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the WSM2780LBW
[Viewing 3 of 3]Noisy
Fixed by
these parts
these parts
Show All
Leaking
Fixed by
these parts
these parts
Show All
Will not agitate
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Dryer was squeeking for a while, and then eventually just quit working.
Took the top and the front panel off (took me a while to figure this out without breaking stuff). Took off belt, pulled out drum, replaced bearing, and then I also had to replace the ball (attached to rear of drum, which slides inside the bearing).
Parts Used:
-
Jesse from Battle Ground, WA
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers
4 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
load noise
took the top off, then the front,there 2 screws that hold the front on. there's a yellow thing on the front took that off, it is held on with one screw. on the back of the dryer on the bottom is a metal plate take that off, to get to the belt take that off. then there' 3 screws in the drum, take them off ,then you can slid the drum out. t
... Read more
hen take 2 screws off the bearing bracket, that's it. easy
Read less
Parts Used:
-
jeff from coldwater, MI
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers, Socket set
5 of 8 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dryer stopped working
What a mess. Partselect shipped the wrong part. I paid a technician to fix it, only to learn the part was wrong. I order the right part. I needed to send it back, reorder the same part, and pay for a second visit from the technician. The nice people at partselect gave me a $7 credit for costing me $200. Losers
Parts Used:
-
Shanice from RESTON, VA
-
Difficulty Level:Very Difficult
-
Total Repair Time:More than 2 hours
2 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!