Models
>
KCMS135SBL6
KCMS135SBL6 KitchenAid Microwave - Overview
Sections of the KCMS135SBL6
[Viewing 5 of 5]Keep searches simple, eg. "belt" or "pump".
Screw
PartSelect #: PS11742721
Manufacturer #: WP488729
Metallic screw that is less than an inch long. Does not include the plastic washer.
$7.91
In Stock
Cooking Rack Support Clip
PartSelect #: PS11740786
Manufacturer #: WP3149478
Sold individually.
$8.83
In Stock
Heat Resistant Adhesive
PartSelect #: PS11728058
Manufacturer #: W10841140
This is a heat-resistant adhesive for your appliance. The heat resistance allows you to stick parts such as grate feet, gaskets, and felt seals in hot areas, such as a cooktop, without compromising th...
$23.85
In Stock
Stir Blade Drive Belt
PartSelect #: PS11740759
Manufacturer #: WP313646
This part connects the stir blade to the fan motor.
$49.90
In Stock
Screw
PartSelect #: PS11748102
Manufacturer #: WPW10068250
This screw is sold individually.
$6.08
In Stock
Fuse - 20Amp
PartSelect #: PS382366
Manufacturer #: 661172
This part helps protect your appliance from short circuits and power surges.
No Longer Available
Outer Door Frame with Glass - Black
PartSelect #: PS337905
Manufacturer #: 3182315
This is just the exterior door and glass assembly. It is NOT the entire door for the microwave.
No Longer Available
Questions And Answers for KCMS135SBL6
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the KCMS135SBL6
[Viewing 1 of 1]Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Microwave plastic door frame broken
Ordered a new door frame morning of March 25.
Part arrived the next morning and by that afternoon, the
replacement was complete. Only four screws held the frame.
Part arrived the next morning and by that afternoon, the
replacement was complete. Only four screws held the frame.
Parts Used:
-
Frederic from Los Altos, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
10 of 14 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Cooking rack support melted
Just pulled the old support out with pliers and installed the new one which snaps in. Not sure why the support melted as it has been the same one twice now. Keep extra support clips on hand, but no need as Parts Select had the new ones here next day.
Parts Used:
-
Ernie from Collinsville, IL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers
6 of 6 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken Belt on Wave Disperser
The microwave is the upper unit of combination microwave & conventional oven. Disconnect power to the unit. Slide unit out of built-in cabinet to expose the top shield of the microwave. Remove 5 screws holding top cover in place. Remove cover, which exposes the belt reel and drive motor. Install the new belt by threading it on the dr
... Read more
ive motor pulley, then walk the new belt on the stirrer pulley. Replace the top cover and reinstall the 5 screws. Reinstall the combination unit in the wall cabinet. Reconnect electrical power. Task Complete. The belt just seem to die of old age about every seven year. Without the wave disperser operating, the microwave oven does not give even heating.
Read less
Parts Used:
-
Harold from Foxfield, CO
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver
6 of 7 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!