This inner door glass is a heat resistant part that fits into a stove, oven, wall oven, cooktop, or range as the inner glass panel of the appliance door. The glass panel allows you to see the items be...
$112.25
In Stock
Order within the next 10 hrs and your part ships today!
This genuine OEM microwave turntable tray is a circular plate made of glass and has a diameter of approximately 16 inches. It rotates food in your microwave oven, so that your food cooks evenly. It is...
$57.88
In Stock
Order within the next 10 hrs and your part ships today!
The bake element is located at the bottom of the oven and gives off heat in order to bake evenly. If you notice that the element is not heating up or is not cooking evenly, it could be because it is b...
$70.38
In Stock
Order within the next 10 hrs and your part ships today!
This oven rack is chrome in color and is approximately 24.76 inches wide by 15.78 inches deep. If your old oven rack is damaged, you should consider replacing it. Many of our customers have determined...
$84.88
In Stock
Order within the next 10 hrs and your part ships today!
This is a multi-use and multi-appliance screw. It can be used on a microwave, refrigerator, range/oven, air conditioner, dehumidifier, washer, or dryer. The measurements of this screw are 8 x 1/2 inch...
$20.79
In Stock
Order within the next 10 hrs and your part ships today!
An oven thermostat is a switch that opens and closes in response to the temperature it senses. It is typically found in the control panel, where a liquid-filled temperature-sensing bulb senses and mai...
$93.52
In Stock
Order within the next 10 hrs and your part ships today!
The temperature sensor measures the temperature inside the oven. If your oven is too hot, not heating evenly, is not heating enough when baking, or simply will not start, you could have a faulty tempe...
$89.97
In Stock
Order within the next 10 hrs and your part ships today!
This touch-up paint can be used on a wide variety of household appliances. It is most often used on washers, dryer, refrigerators, dishwashers, ranges, freezers, trash compactors, or microwaves. It is...
$8.00
In Stock
Order within the next 10 hrs and your part ships today!
This broil element is for ranges.
Broil element is at the top of the oven and supplies the heat for broiling.
Disconnect electrical power to the range before installing this part. Wear work glov...
$101.89
In Stock
Order within the next 10 hrs and your part ships today!
This part is a light bulb that is 120-130 volts and 15 watts, and is used in conjunction with your range or wall oven. The function of this bulb is to illuminate the interior of the oven.Before making...
$47.60
In Stock
Order within the next 10 hrs and your part ships today!
Order within the next 10 hrs and your part ships today!
Questions And Answers for GSC308PRS01
Ask our experts a question about this model and we'll get back to you as soon as possible!
3 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Mark
March 14, 2020
Set convection bake to 400°, oven comes up to temperature and dings that is there but the broiler element never turns off just keeps taking the temperature higher and higher till the door locks and airs out over temperature. Put in relay t92p7a22-120,temperature probe and thermal fuse..... still doing the exact same thing. sidenote when it comes up to 400° i can manually turn the oven off and it will turn off. type in 350 and the broiler element immediately turns right back on.
For model number GSC308PRS01
Hello, Thank you for your question. I would look into the Limit thermostat- PartSelect Number PS11747249. We hope this helps.
Was this helpful?
Thank you for voting!
DOUG
November 1, 2022
The glass on the outside of the door broke. The two inside glass panes are still intact. Is the outside glass or entire door assembly available for replacement?
For model number GSC308PRS01
Hello Doug, thank you for contacting us. We have researched the model you have provided and have found that the part you are looking for is the outer glass, part number PS11745879. Customer service is available 7 days a week if you need help placing an order. Glad to be of assistance!
How do I replace the microwave light? It's not the same kind as another video you provided. Is the microwave light Part Select # PS11754756?
For model number GSC308PRS01
Hello Ken, thank you for your inquiry. Use the following instructions to replace the light in the microwave:
1. Remove the screws on the side of the control panel and pull the panel off.
2. Disconnect the white wire connected to the control panel.
3. Remove the upper and lower vent grilles.
4. Remove the screws at the bottom of the microwave.
5. Pull the microwave out of the mounting frame and remove the insulation plate.
6. The light socket is located in the center. Squeeze the retainer spring from one side and release it.
7. Remove the light bulb from the socket and insert a new one.
We hope this helps.
Was this helpful?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
Easily removed the door from the oven by releasing clips attached to the door hinge -- very nicely engineered. Removed about 6 philips head screws to allow the door assembly to be taken apart for access to the glass. Lifted out the broken glass, cleaned the inside of the door, installed the new glass, reassembled the door (a two minute
... Read more project), and reattached the door to the oven. Cleaning the inside of the door took longer than the actual repair!
I removed the two screws that held the bake element in place. Next I removed the Bake Element. I had to unscrew the oven to go behind it because when one piece off of the element broke, it slide back behind the oven. I pushed the wire back thru the piece holes, connected the Element, and pushed the element with the wires back through the
... Read moreholes. I rescrewed the element in place and the oven. PartSelect helped me to save this year's Christmas.
This built-in oven was slid out of it's space and set on a box. I removed the back cover with nut driver and located the safety overload device. removed nuts and used pliers to remove wires and replace them. The power must be off to do this repair.Replaced the cover and slid back into place. This could be a lot more difficult if your pow
... Read moreer cord or gas line is not long enough to make it out of your wall space. Or of your oven is attached well to the frame.
