My Orders
Frigidaire Washer Parts
GET YOUR OFFICIAL Frigidaire PARTS TO ENSURE VICTORY
Popular Frigidaire Washer Parts
This is a door latch, also known as a door strike, for some models of washing machine. This part secures to the door of the washer and secures the door when it is shut, to ensure the inside drum of the washer does not leak. If your washer does not start properly and/or shut all the way, this latch is likely causing the issues you are experiencing and needs to be replaced. This latch is made of a brushed metal material and features two holes to secure it with screws. To replace this latch, simply unthread the screws of the old latch to remove it, and secure the new latch with the existing screws. This latch is not sold with any other parts or accessories, so any securing screws are sold separately.
This is a door latch, also known as a door strike, for some models of washing machine. This part secures to the door of the washer and secures the door when it is shut, to ensure the inside drum of the washer does not leak. If your washer does not start properly and/or shut all the way, this latch is likely causing the issues you are experiencing and needs to be replaced. This latch is made of a brushed metal material and features two holes to secure it with screws. To replace this latch, simply unthread the screws of the old latch to remove it, and secure the new latch with the existing screws. This latch is not sold with any other parts or accessories, so any securing screws are sold separately.
Installation Instructions
Kim from LAFAYETTE, CA
latch broke, door wouldn't shut, washer wouldn't run - no fun
I googled the problem, read the recommendation found the part and read that it was an easy fix. Took the broken part off the door and noticed the broke off piece was in the latch on the machine. Ordered the two parts, paid the $30 2-day delivery. Parts arrived and the machine was up and runnning in under 5 minutes
This is a door striker, it is gray in color and is a part found on your washer. The purpose of the striker is to keep your washer door closed for usage. This piece will attach to your appliance lid and will activate the door switch when your lid is closed. The most common reasons for needing to replace this part are if your lid will not consistently open or close, and your washer will not consistently start. The only tool you will need to complete this installation is a Phillips screwdriver.
This is a door striker, it is gray in color and is a part found on your washer. The purpose of the striker is to keep your washer door closed for usage. This piece will attach to your appliance lid and will activate the door switch when your lid is closed. The most common reasons for needing to replace this part are if your lid will not consistently open or close, and your washer will not consistently start. The only tool you will need to complete this installation is a Phillips screwdriver.
Installation Instructions
Joy from Columbia, MO
Broken Door Catch
This was one of the simpliest repairs I have ever done taking less than 5 minutes to complete. On the inner door I removed the two screws that hold the plastic catch in place. I then removed the broken catch and put the new catch in place. Finally I replaced the two screws that hold the catch in place and it was done.
This door lock assembly is an essential component for ensuring the safe and efficient operation of your washing machine. Designed to prevent the door from opening during the wash and spin cycles, this lock assembly enhances both safety and performance. It is a genuine OEM part compatible with select Frigidaire, Electrolux, White Westinghouse, and Tappan washing machines. The durable construction ensures reliable functionality, safeguarding against accidental openings that could disrupt your machine’s operation. If your washer door fails to lock properly, replacing this part can restore optimal performance. Before purchasing, confirm compatibility by checking your model number, as parts may vary in size and shape. Always disconnect the washer from its power source and wear protective gloves during installation to ensure safety.
This door lock assembly is an essential component for ensuring the safe and efficient operation of your washing machine. Designed to prevent the door from opening during the wash and spin cycles, this lock assembly enhances both safety and performance. It is a genuine OEM part compatible with select Frigidaire, Electrolux, White Westinghouse, and Tappan washing machines. The durable construction ensures reliable functionality, safeguarding against accidental openings that could disrupt your machine’s operation. If your washer door fails to lock properly, replacing this part can restore optimal performance. Before purchasing, confirm compatibility by checking your model number, as parts may vary in size and shape. Always disconnect the washer from its power source and wear protective gloves during installation to ensure safety.
Installation Instructions
Kim from LAFAYETTE, CA
latch broke, door wouldn't shut, washer wouldn't run - no fun
I googled the problem, read the recommendation found the part and read that it was an easy fix. Took the broken part off the door and noticed the broke off piece was in the latch on the machine. Ordered the two parts, paid the $30 2-day delivery. Parts arrived and the machine was up and runnning in under 5 minutes
$83.55
In Stock
This door lock and switch assembly is manufactured to lock the door on your front load washer to prevent it from opening while it is running. You may need to replace the door lock and switch if the door does not open or lock. Your washer will not start if the door does not lock. This part is also known as a washing machine door lock assembly. As per the manufacturer, some models require a new wire harness and a door strike for this door lock assembly to work on the appliance. The original style lock would require the door lock kit.
This door lock and switch assembly is manufactured to lock the door on your front load washer to prevent it from opening while it is running. You may need to replace the door lock and switch if the door does not open or lock. Your washer will not start if the door does not lock. This part is also known as a washing machine door lock assembly. As per the manufacturer, some models require a new wire harness and a door strike for this door lock assembly to work on the appliance. The original style lock would require the door lock kit.
Installation Instructions
DOUG from KING FERRY, NY
Door on washer wouldn't lock or start
1. Unplug unit.
2. Unscrew 2 nuts holding top in place in rear of unit using phillips head screwdriver.
3.Slide top back and remove.
4. Open door of washer and unscrew 2 screws holding in door lock unit.
5.Pull out unit from the top and install new unit reconnecting the 3 wire connections.
2. Unscrew 2 nuts holding top in place in rear of unit using phillips head screwdriver.
3.Slide top back and remove.
4. Open door of washer and unscrew 2 screws holding in door lock unit.
5.Pull out unit from the top and install new unit reconnecting the 3 wire connections.
This shock absorber kit is an authentic OEM part that is sourced directly from the manufacturer. The kit includes two dual-stage shock absorbers, one spare shock mounting pin, and four locking nuts. These shock absorbers keep your front-load washer from shaking vigorously by absorbing and reducing vibrations from the wash and spin cycles of your appliance. This kit comes with two shock absorbers because it is recommended to replace both at the same time, as they wear at the same rate. To access your washer shock absorbers, simply remove the lower access panel after disconnecting the power to the appliance.
This shock absorber kit is an authentic OEM part that is sourced directly from the manufacturer. The kit includes two dual-stage shock absorbers, one spare shock mounting pin, and four locking nuts. These shock absorbers keep your front-load washer from shaking vigorously by absorbing and reducing vibrations from the wash and spin cycles of your appliance. This kit comes with two shock absorbers because it is recommended to replace both at the same time, as they wear at the same rate. To access your washer shock absorbers, simply remove the lower access panel after disconnecting the power to the appliance.
Installation Instructions
Douglas from Medical Lake, WA
Both vibration shock absorbers broken
removed 2 screws and removed top access cover. removed 2 screws and removed front access cover. removed 4 retaining pins (one with nammer and punch because it was stuck) connected lower ends of new shocks with plastic pins, extended each shock to slip fit and connected upper ends to wash tub mounts. Reinstalled panels. I wish I could sa
... Read more
y that it all went well from there but......when the shocks broke, apparently the hit the motor took was enough to cause an electronic failure of the speed cycle control chip. Now Im waiting for that part.
Read less
MAKE THIS REPAIR A GUARANTEED WIN
OVER 2 MILLION PARTS TO ENSURE VICTORY
This rubber V-style drive belt slips on the motor pulley to bring the basket to the required speed. If you notice a burning rubber smell or grinding noises coming from your washer, your washer does not start, drain, spin properly (will not spin/spins slowly/will not agitate properly), or if your washer shakes or moves during the cycle; check your drive belt for signs of wear and tear. Replace the drive belt if you notice that the belt looks damaged. This OEM part is approximately 35 inches in length, and sold individually.
This rubber V-style drive belt slips on the motor pulley to bring the basket to the required speed. If you notice a burning rubber smell or grinding noises coming from your washer, your washer does not start, drain, spin properly (will not spin/spins slowly/will not agitate properly), or if your washer shakes or moves during the cycle; check your drive belt for signs of wear and tear. Replace the drive belt if you notice that the belt looks damaged. This OEM part is approximately 35 inches in length, and sold individually.
Installation Instructions
rodney from fairfield bay, AR
replace broken drive belt
carefully pry up on front washer top to release plastic keeper pins,remove 2 phillips screws from beneath lower front washer panel,slightly lift upward on panel to release.remove old broken belt,push new belt beneath large tub pulley,put belt on small motor pulley,push back belt tension /idler arm,start belt on large tub pulley,turn tub p
... Read more
ulley by hand to run belt on,release tension on idler arm.replace front panel and lower top.WALAAH!!!! you are done.
Read less
This is a bellow, though it may also be known as a door boot seal, and it is a part for your washing machine. The function of the bellow is to prevent leaks by forming a seal in between the wash tub and the door of the washing machine. The boot gasket measures to be almost 21 inches by 21 inches and is gray in color. Take caution, as this part is prone to tearing if the washer is frequently overloaded. To complete this repair, you will need a Phillips screwdriver, a number two square bit, and a pair of needle-nose pliers.
This is a bellow, though it may also be known as a door boot seal, and it is a part for your washing machine. The function of the bellow is to prevent leaks by forming a seal in between the wash tub and the door of the washing machine. The boot gasket measures to be almost 21 inches by 21 inches and is gray in color. Take caution, as this part is prone to tearing if the washer is frequently overloaded. To complete this repair, you will need a Phillips screwdriver, a number two square bit, and a pair of needle-nose pliers.
Installation Instructions
Michelle from Loves Park, IL
Original bellow had 2 largish holes in the upper left quadrant; random leaking.
Bought new part. #1 Lesson learned: Always inspect the actual part number of the ordered/received part. Verify with number marked on the item somewhere. We did not do this and turned out we reinstalled a slightly smaller bellow (wrong part number received in shipment). We were able to fully install it but it was minutely not laying perfec
... Read more
tly around the diameter. So minor we did not notice. We did have great difficulty installing though. Anyway, after 1st test run, bellow already had developed a small hole in bottom right quadrant from rubbing on the drum. Left a bunch of gray powdery debris on the drum too. We did not realize error until that point. Took bellow off again to verify part number on it. It was wrong. That explained why the door was so very tight to close and difficult to open. Other than all that, use the video to do the install. It was free to view and easy to follow.
Read less
This OEM water inlet valve assembly with flow meter fits select Frigidaire, Electrolux, White Westinghouse, and Tappan washers. It regulates water flow for efficient operation and energy savings. Unplug the washer and shut off the water supply before installing. Refer to your owner’s manual for model-specific guidance. Verify compatibility before ordering.
This OEM water inlet valve assembly with flow meter fits select Frigidaire, Electrolux, White Westinghouse, and Tappan washers. It regulates water flow for efficient operation and energy savings. Unplug the washer and shut off the water supply before installing. Refer to your owner’s manual for model-specific guidance. Verify compatibility before ordering.
This is a 120 volt, 60 hertz drain pump that is manufactured to remove water from the tub of your washer once your clothes are washed. This part is the pump and motor assembly, which includes a red flapper to prevent drain backflow. You will need to remove the front panel of your washer to access the drain pump. The tools you will need for the repair are a Phillips screw driver, a putty knife, a pair of slip joint pliers, and a 5/16 nut driver. Be sure to disconnect the water supply from your washer before doing the repair. The metal edges on the appliance are sharp, so use work gloves to safely complete the repair.
This is a 120 volt, 60 hertz drain pump that is manufactured to remove water from the tub of your washer once your clothes are washed. This part is the pump and motor assembly, which includes a red flapper to prevent drain backflow. You will need to remove the front panel of your washer to access the drain pump. The tools you will need for the repair are a Phillips screw driver, a putty knife, a pair of slip joint pliers, and a 5/16 nut driver. Be sure to disconnect the water supply from your washer before doing the repair. The metal edges on the appliance are sharp, so use work gloves to safely complete the repair.
Installation Instructions
kenneth from willard, OH
would't spin all water out or rinse out clothes
uplugged washer took front off washer 2 screws pryed up top pump was mounted with 2 screws and 2 wires took off found change in pump and the fins to pump worn off ordered part off line the wait for part was longer than the amount of time to fix problem and cost of part saved me about $25-35 if I was to buy local worth wait save money and
... Read more
fix problem washes like new spins and drains all water from tub.
Read less
Installation Instructions
Jeff from MCCORDSVILLE, IN
Original Drawer Assembly bottom broke apart leaking water down the front of washer.
Very simple, removed Drawer Assembly from unit. Removed detergent bowl and front cover. Installed front cover and detergent bowl on replacement Drawer Assembly. Returned installed replacement Drawer Assembly on unit.