My Orders
Washer Valves
MAKE THIS REPAIR A GUARANTEED WIN
OVER 2 MILLION PARTS TO ENSURE VICTORY
Shop By Brand
View More
Popular Washer Valves
This is an inlet valve for your washing machine. The inlet valve is an electrically controlled valve with a solenoid that opens and closes as needed, during the water filling cycle of the washing machine. This inlet valve features two inlets, one for hot and one for cold water, and three push-on valves that connect within your washing machine. If your washer is having issues filling or is leaking water from the area of the inlet valve, it needs to be replaced immediately. Replacing this valve will require a screwdriver and a wrench to replace. This inlet valve is an OEM part and is sold individually.
This is an inlet valve for your washing machine. The inlet valve is an electrically controlled valve with a solenoid that opens and closes as needed, during the water filling cycle of the washing machine. This inlet valve features two inlets, one for hot and one for cold water, and three push-on valves that connect within your washing machine. If your washer is having issues filling or is leaking water from the area of the inlet valve, it needs to be replaced immediately. Replacing this valve will require a screwdriver and a wrench to replace. This inlet valve is an OEM part and is sold individually.
Installation Instructions
Marian from GREYBULL, WY
Faulty fill valve
Did troubleshooting after code LF showed on indicator window. Did troubleshooting; checked hoses for obstructions and small filters on inlets. All good. Ordered new fill valve. Came in a few days, good service.
Removed control panel top by removing screws on back of control panel, then by pushing putty knife under each side to rele ... Read more ase spring clips. Carefully lifted cover and set onto lid. Photographed fill valve at left side as you are standing in front of machine. Removed screws with small ratchet. Carefully removed wires via clips. Lifted out valve.
Attached wires to new, set back into its place, replaced screws, tightened but not too tight so as to break part. Replaced control panel, pushing downward to engage spring clips, then replace screws on back.
Re attached hoses, ensuring they were on the correct sides, plugged machine into power, ran through cycle and VIOLA!! Worked perfectly!! After a couple weeks, still working perfectly! Was VERY happy it was only fill valve and not mother board as the cost was a fraction.
I found trouble shooting videos to be very helpful. Your service quite good.
Removed control panel top by removing screws on back of control panel, then by pushing putty knife under each side to rele ... Read more ase spring clips. Carefully lifted cover and set onto lid. Photographed fill valve at left side as you are standing in front of machine. Removed screws with small ratchet. Carefully removed wires via clips. Lifted out valve.
Attached wires to new, set back into its place, replaced screws, tightened but not too tight so as to break part. Replaced control panel, pushing downward to engage spring clips, then replace screws on back.
Re attached hoses, ensuring they were on the correct sides, plugged machine into power, ran through cycle and VIOLA!! Worked perfectly!! After a couple weeks, still working perfectly! Was VERY happy it was only fill valve and not mother board as the cost was a fraction.
I found trouble shooting videos to be very helpful. Your service quite good.
Read less
The hot water inlet valve on your washing machine controls the water flow into the washer. This inlet valve has a standard hose fitting inlet and one water outlet. The water inlet valve opens to allow water to enter the washing machine. If the water inlet valve is defective, the washer may leak, fill slowly, or not fill at all. To test your valve, unplug the washer when the symptom occurs. If the washer continues to fill, then your inlet valve is defective. This part is approximately 3 inches long x 3 inches wide.
The hot water inlet valve on your washing machine controls the water flow into the washer. This inlet valve has a standard hose fitting inlet and one water outlet. The water inlet valve opens to allow water to enter the washing machine. If the water inlet valve is defective, the washer may leak, fill slowly, or not fill at all. To test your valve, unplug the washer when the symptom occurs. If the washer continues to fill, then your inlet valve is defective. This part is approximately 3 inches long x 3 inches wide.
Installation Instructions
Khanh from CHICAGO, IL
Water continued to fill into the drum slowly after the load was done.
Watched a you tube video and followed the instructions. Even had my 11 and 13 yo old help and do most of the work. Very easy to fix both hot and cold inlet at the same time. Didn't know which one was causing the problem so I decided to replace both.
This is an authentic LG water inlet valve for a top-load washer. It is designed to control the flow of water into the washer. If your washer is filling slowly, making loud noises, overflowing, or stopping in the middle of a cycle, you may need to replace the water inlet valve. Be sure to disconnect the power and water supply before you begin this repair.
This is an authentic LG water inlet valve for a top-load washer. It is designed to control the flow of water into the washer. If your washer is filling slowly, making loud noises, overflowing, or stopping in the middle of a cycle, you may need to replace the water inlet valve. Be sure to disconnect the power and water supply before you begin this repair.
Installation Instructions
Flora from MIAMI, FL
Water continued leaking into washer after the end of cycle through the water inlet valve.
Did the repair Myself. Saved $ 400.00 in the process.
The cold water inlet valve on your washing machine dispenses the cold water and bleach into the washer in the prewash cycle. This inlet valve has a standard hose fitting inlet and 2 water outlets facing 45 degrees to the left. The water inlet valve opens to allow water to enter the washing machine. If the water inlet valve is defective, the washer may leak, fill slowly, or not fill at all. To test your valve, unplug the washer when the symptom occurs. If the washer continues to fill, then your inlet valve is defective. This part is approximately 4 inches long x 3 inches wide.
The cold water inlet valve on your washing machine dispenses the cold water and bleach into the washer in the prewash cycle. This inlet valve has a standard hose fitting inlet and 2 water outlets facing 45 degrees to the left. The water inlet valve opens to allow water to enter the washing machine. If the water inlet valve is defective, the washer may leak, fill slowly, or not fill at all. To test your valve, unplug the washer when the symptom occurs. If the washer continues to fill, then your inlet valve is defective. This part is approximately 4 inches long x 3 inches wide.
What this part fixes:
- Does not dispense fabric softener or detergent
- Leaking
- No hot or cold water
Installation Instructions
John from Northport, NY
Inlet valve leak
Followed directions on the video and went like a charm. Very impressed with service and video
The water inlet valve on your washing machine is used to fill the tub with cold, warm, or hot water for the wash and rinse cycles. This part could have either a blue or green-colored valve body. There are two ports for water to enter and this valve is compatible with a half-inch ID hose. It has two 3/4-11x1/2 NHT hose threads. You may have a faulty valve if your washer is leaking, has no hot or cold water, will not stop filling with water, will not fill with water, fills and drains at the same time, or is noisy. To confirm that the valve is faulty, unplug the washer when the symptom occurs. If the washer continues to fill, then the inlet valve is defective.
The water inlet valve on your washing machine is used to fill the tub with cold, warm, or hot water for the wash and rinse cycles. This part could have either a blue or green-colored valve body. There are two ports for water to enter and this valve is compatible with a half-inch ID hose. It has two 3/4-11x1/2 NHT hose threads. You may have a faulty valve if your washer is leaking, has no hot or cold water, will not stop filling with water, will not fill with water, fills and drains at the same time, or is noisy. To confirm that the valve is faulty, unplug the washer when the symptom occurs. If the washer continues to fill, then the inlet valve is defective.
Installation Instructions
Don from Wyoming, MN
Washer stopped at rinse cycle
Removed the top and back panels. Replaced
compoments and reassembled.
Test run machine. Ran like new!
compoments and reassembled.
Test run machine. Ran like new!
MAKE THIS REPAIR A GUARANTEED WIN
OVER 2 MILLION PARTS TO ENSURE VICTORY
This water inlet valve is for washers.
The water inlet valve controls the water flow into the washer.
Unplug the washer and shut off the water supply before installing this part. Wear work gloves to protect your hands.
This water inlet valve is for washers.
The water inlet valve controls the water flow into the washer.
Unplug the washer and shut off the water supply before installing this part. Wear work gloves to protect your hands.
Installation Instructions
Patricia from MURPHYSBORO, IL
Water would not fill the washer except for 4 inches.
Once we put in the new Water Inlet Valve, the auto sensor works now and I can wash any size load
This water inlet valve assembly controls the flow of hot and cold water into your washing machine, ensuring each cycle uses the correct amount of water. If your washer isn’t filling properly, is leaking, or continues to fill even when turned off, the valve may be faulty and require replacement. The part is housed in durable gray plastic and does not include a gasket. Installation may require basic tools and should be done with the power and water supply disconnected.
This water inlet valve assembly controls the flow of hot and cold water into your washing machine, ensuring each cycle uses the correct amount of water. If your washer isn’t filling properly, is leaking, or continues to fill even when turned off, the valve may be faulty and require replacement. The part is housed in durable gray plastic and does not include a gasket. Installation may require basic tools and should be done with the power and water supply disconnected.
Installation Instructions
George from CLARKSVILLE, TN
Cold water dripping inside of washer from inlet valve
Turn off hot and cold water supply valves feeding washer.
Disconnect both water hoses from washing machine.
Remove two screws (one on each side) from upper silver colored metal plate on back of washer to allow access to (blue) water inlet valve.
Slightly lift the bottom portion of metal plate and slide to release hooks for ... Read more easy removal.
Pull back and tilt forward plastic control panel to get it out of your way.
Disconnect two electrical connections (one on each side) of water inlet valve. One of these came off easily but the other one was stubborn and I had to force it off with a screw driver. If there is an easier way I don't know what it is.
Remove two screws from water inlet valve. (one on each side)
Gently pull up on stainless steel water temperature sensor located in the middle of the water inlet control valve. It has a black wire connected to it so be careful.
Once you have disconnect the sensor you can remove the water inlet valve.
If you look closely you will see a small blue O-ring in the hole where you removed the water temp sensor from the water inlet valve.
The new valve DOES NOT come with a replacement O-ring so you
will have to re-use the old one. I used a small jeweler's screwdriver to get the old out of the hole.
Don't forget to install the O-ring or your washer WILL leak!
Put everything back together in reverse order.
Check hose connections for leaks.
Hope this helps somebody. Wish I had known about the O-ring. It would have saved me a headache.
Disconnect both water hoses from washing machine.
Remove two screws (one on each side) from upper silver colored metal plate on back of washer to allow access to (blue) water inlet valve.
Slightly lift the bottom portion of metal plate and slide to release hooks for ... Read more easy removal.
Pull back and tilt forward plastic control panel to get it out of your way.
Disconnect two electrical connections (one on each side) of water inlet valve. One of these came off easily but the other one was stubborn and I had to force it off with a screw driver. If there is an easier way I don't know what it is.
Remove two screws from water inlet valve. (one on each side)
Gently pull up on stainless steel water temperature sensor located in the middle of the water inlet control valve. It has a black wire connected to it so be careful.
Once you have disconnect the sensor you can remove the water inlet valve.
If you look closely you will see a small blue O-ring in the hole where you removed the water temp sensor from the water inlet valve.
The new valve DOES NOT come with a replacement O-ring so you
will have to re-use the old one. I used a small jeweler's screwdriver to get the old out of the hole.
Don't forget to install the O-ring or your washer WILL leak!
Put everything back together in reverse order.
Check hose connections for leaks.
Hope this helps somebody. Wish I had known about the O-ring. It would have saved me a headache.
Read less
This part is used to help control and balance the water temperature flowing in to the washer tub.
This part is used to help control and balance the water temperature flowing in to the washer tub.
Installation Instructions
Barb from Blackriver Falls, WI
fill valve bad
took back off then removed valve replaced with new one works good
This is a water inlet valve made for washing machines. This part is used to control the flow of water into the fill hose of the washing machine, to allow the washer to fill up with water. If your washing machine is not filling up with water properly, or if you are noticing leaks underneath your washing machine, the inlet valve has likely failed and you will likely need to replace it. This OEM inlet valve features two different inlets for hot and cold water but does not come with any other parts or accessories for installation. To replace this water inlet valve, you will need tools such as a screwdriver or wrench to gain access to it and remove it.
This is a water inlet valve made for washing machines. This part is used to control the flow of water into the fill hose of the washing machine, to allow the washer to fill up with water. If your washing machine is not filling up with water properly, or if you are noticing leaks underneath your washing machine, the inlet valve has likely failed and you will likely need to replace it. This OEM inlet valve features two different inlets for hot and cold water but does not come with any other parts or accessories for installation. To replace this water inlet valve, you will need tools such as a screwdriver or wrench to gain access to it and remove it.
Installation Instructions
Brian from VESTAL, NY
Water was dripping while the machine wasn’t running
Removed two screws that held the control panel from the back with a power drill. Pop the control panel loose with a screwdriver from the top of the machine with the quick disconnects. After turning both the hot and cold water off I remove the hoses with pliers removed two screws with the power drill that hold the water inlet valve in plac
... Read more
e disconnected the wire harness plug And removed water inlet valve swap, the original harness to the new water inlet valve and follow the steps backwards to finish
Read less
This OEM water inlet valve assembly with flow meter fits select Frigidaire, Electrolux, White Westinghouse, and Tappan washers. It regulates water flow for efficient operation and energy savings. Unplug the washer and shut off the water supply before installing. Refer to your owner’s manual for model-specific guidance. Verify compatibility before ordering.
This OEM water inlet valve assembly with flow meter fits select Frigidaire, Electrolux, White Westinghouse, and Tappan washers. It regulates water flow for efficient operation and energy savings. Unplug the washer and shut off the water supply before installing. Refer to your owner’s manual for model-specific guidance. Verify compatibility before ordering.