My Orders
Inglis Washer Valves
GET YOUR OFFICIAL Inglis PARTS TO ENSURE VICTORY
Popular Inglis Washer Valves
The water inlet valve on your washing machine is used to fill the tub with cold, warm, or hot water for the wash and rinse cycles. This part could have either a blue or green-colored valve body. There are two ports for water to enter and this valve is compatible with a half-inch ID hose. It has two 3/4-11x1/2 NHT hose threads. You may have a faulty valve if your washer is leaking, has no hot or cold water, will not stop filling with water, will not fill with water, fills and drains at the same time, or is noisy. To confirm that the valve is faulty, unplug the washer when the symptom occurs. If the washer continues to fill, then the inlet valve is defective.
The water inlet valve on your washing machine is used to fill the tub with cold, warm, or hot water for the wash and rinse cycles. This part could have either a blue or green-colored valve body. There are two ports for water to enter and this valve is compatible with a half-inch ID hose. It has two 3/4-11x1/2 NHT hose threads. You may have a faulty valve if your washer is leaking, has no hot or cold water, will not stop filling with water, will not fill with water, fills and drains at the same time, or is noisy. To confirm that the valve is faulty, unplug the washer when the symptom occurs. If the washer continues to fill, then the inlet valve is defective.
Installation Instructions
Don from Wyoming, MN
Washer stopped at rinse cycle
Removed the top and back panels. Replaced
compoments and reassembled.
Test run machine. Ran like new!
compoments and reassembled.
Test run machine. Ran like new!
This water inlet valve is for washers.
The water inlet valve controls the water flow into the washer.
Unplug the washer and shut off the water supply before installing this part. Wear work gloves to protect your hands.
This water inlet valve is for washers.
The water inlet valve controls the water flow into the washer.
Unplug the washer and shut off the water supply before installing this part. Wear work gloves to protect your hands.
Installation Instructions
Patricia from MURPHYSBORO, IL
Water would not fill the washer except for 4 inches.
Once we put in the new Water Inlet Valve, the auto sensor works now and I can wash any size load
This part is used to help control and balance the water temperature flowing in to the washer tub.
This part is used to help control and balance the water temperature flowing in to the washer tub.
Installation Instructions
Barb from Blackriver Falls, WI
fill valve bad
took back off then removed valve replaced with new one works good
This is an inlet valve for various washing machines. Inlet valves are responsible for opening and closing as needed, to allow water to enter the washer during the washing cycle. This inlet valve features a hot and cold-water valve, as well as the necessary wire harness to easily plug it in. Since inlet valves are an electrically controlled solenoid valve, they can fail either due to electrical failure such a short, or after long, extended use. If your inlet valve fails, your washer will likely relay an error code, or it simply will not wash your clothes due to the lack of water, and the valves will need to be replaced. Replacing this valve will require a screwdriver and/or socket wrench, and some disassembly of your washer will be necessary. This inlet valve is an individually sold OEM part and does not come with any accessories or other parts.
This is an inlet valve for various washing machines. Inlet valves are responsible for opening and closing as needed, to allow water to enter the washer during the washing cycle. This inlet valve features a hot and cold-water valve, as well as the necessary wire harness to easily plug it in. Since inlet valves are an electrically controlled solenoid valve, they can fail either due to electrical failure such a short, or after long, extended use. If your inlet valve fails, your washer will likely relay an error code, or it simply will not wash your clothes due to the lack of water, and the valves will need to be replaced. Replacing this valve will require a screwdriver and/or socket wrench, and some disassembly of your washer will be necessary. This inlet valve is an individually sold OEM part and does not come with any accessories or other parts.
Installation Instructions
melinda from HARROGATE, TN
Water would not stop flowing.
*be sure to turn water off, unplug machine, and unscrew the water hoses from the rear of the washer.
1. Removed screws from the back of the washer, just the top part where the controls are.
2. Removed the panel.
3. Use a putty knife or screw driver to pop off the top panel.
4. Remove the screws from the inlet valve.< ... Read more br />5. Unplug the wires connecting the inlet valve to the washer.
6. Lift out the old inlet valve.
7. Replace with the new inlet valve.
8. Plug the new wires into the washer.
9. Replace the screws in the inlet valve.
10. Replace the top.
11. Replace the rear panel and screws.
12. Reconnect the water hoses, careful not to mix the hot and cold.
13. Plug the machine back in and you're finished!
1. Removed screws from the back of the washer, just the top part where the controls are.
2. Removed the panel.
3. Use a putty knife or screw driver to pop off the top panel.
4. Remove the screws from the inlet valve.< ... Read more br />5. Unplug the wires connecting the inlet valve to the washer.
6. Lift out the old inlet valve.
7. Replace with the new inlet valve.
8. Plug the new wires into the washer.
9. Replace the screws in the inlet valve.
10. Replace the top.
11. Replace the rear panel and screws.
12. Reconnect the water hoses, careful not to mix the hot and cold.
13. Plug the machine back in and you're finished!
Read less
This water inlet valve is a key component in top-load washing machines, responsible for regulating the flow of hot and cold water into the appliance. It electronically opens and closes to deliver the correct amount of water, balances temperature for each cycle, and helps maintain proper water levels. Constructed from durable, high-quality materials, the valve is designed to withstand frequent use and prevent issues such as overfilling, insufficient water flow, or leaks. Replacing a faulty valve can resolve symptoms like the washer not filling, continuous water flow, uneven temperature control, or water leakage from the rear of the unit, restoring efficient and safe operation.
This water inlet valve is a key component in top-load washing machines, responsible for regulating the flow of hot and cold water into the appliance. It electronically opens and closes to deliver the correct amount of water, balances temperature for each cycle, and helps maintain proper water levels. Constructed from durable, high-quality materials, the valve is designed to withstand frequent use and prevent issues such as overfilling, insufficient water flow, or leaks. Replacing a faulty valve can resolve symptoms like the washer not filling, continuous water flow, uneven temperature control, or water leakage from the rear of the unit, restoring efficient and safe operation.
Installation Instructions
Armand from WESTPORT, MA
Water inlet nozzle was stripped and leak
Remove the front panel and back panel unplug the part unscrewed the part and replace it with the new one
MAKE THIS REPAIR A GUARANTEED WIN
OVER 2 MILLION PARTS TO ENSURE VICTORY
This is a water inlet valve for models of Whirlpool washing machines. The water inlet valve is designed to regulate and control the water entering the appliance depending on the cycle, using an electrical device called a solenoid. This water inlet valve features two inlets, one for hot water and one for cold, as well as a wire harness to power and control the electric solenoid of each. If your washer is having issues with filling, the inlet valve is likely bad or potentially worn out and in need of replacement. Replacing this valve will require a screwdriver, wrench, and pliers. This water inlet valve is an OEM part from Whirlpool and is sold individually.
This is a water inlet valve for models of Whirlpool washing machines. The water inlet valve is designed to regulate and control the water entering the appliance depending on the cycle, using an electrical device called a solenoid. This water inlet valve features two inlets, one for hot water and one for cold, as well as a wire harness to power and control the electric solenoid of each. If your washer is having issues with filling, the inlet valve is likely bad or potentially worn out and in need of replacement. Replacing this valve will require a screwdriver, wrench, and pliers. This water inlet valve is an OEM part from Whirlpool and is sold individually.
Installation Instructions
John from SAINT JOSEPH, MI
Leaking water inlet valve assembly
Remove upper rear panel with drill driver and 1/4" nut driver bit. using the angle bit holder and torx bit remove the two screws holding the assembly in place. Slide out the old assembly and disconnect the wiring harness at the machine. Slide new assembly in place. While holding it down start both screws by hand, then use the driver/an
... Read more
gle holder to tighten screws. Reattach the wiring harness and rear plate(s).
Read less
$56.33
In Stock
This water inlet valve attaches the water lines to the back of your appliance. The attaching solenoids on the valve open and close according to the desired temperature, or amount of water needed.
This water inlet valve attaches the water lines to the back of your appliance. The attaching solenoids on the valve open and close according to the desired temperature, or amount of water needed.
Installation Instructions
Pat from Hilliard, FL
Post drip from water inlet
To replace the inlet solenoid valve/thermistor assembly:
Unplug the washer.
Turn the water off and unscrew the hoses from the inlet.
Unsnap the end caps from the top control panel.
Remove the exposed screws from each end of the panel (#2 Phillips).
Pull the panel out of the way and pop out the two retain ... Read more ing clips that hold the back of the machine to the cabinet. They are located under the control panel.
Remove the mounting screw from the valve assembly (1/4-inch driver).
Pull the back away from the cabinet far enough to remove the valve, but don't let the wires get cut.
Disconnect the wires. To unplug the solenoid connectors, lift the long tab with a screwdriver.
Disconnect the water outlet hose.
Connect the wires and hose to the new valve assembly. The red connector goes to the hot water valve. The thermistor wires (the two individual connectors) can be connected to either terminal. It does not matter if they are reversed.
Put the valve back in place and install the screw.
Hook up and turn the water on.
Plug in the machine and test the valve.
Unplug the power and reinstall the back and the control panel. The back-to-cabinet clips can be snapped back in place easily.
Unplug the washer.
Turn the water off and unscrew the hoses from the inlet.
Unsnap the end caps from the top control panel.
Remove the exposed screws from each end of the panel (#2 Phillips).
Pull the panel out of the way and pop out the two retain ... Read more ing clips that hold the back of the machine to the cabinet. They are located under the control panel.
Remove the mounting screw from the valve assembly (1/4-inch driver).
Pull the back away from the cabinet far enough to remove the valve, but don't let the wires get cut.
Disconnect the wires. To unplug the solenoid connectors, lift the long tab with a screwdriver.
Disconnect the water outlet hose.
Connect the wires and hose to the new valve assembly. The red connector goes to the hot water valve. The thermistor wires (the two individual connectors) can be connected to either terminal. It does not matter if they are reversed.
Put the valve back in place and install the screw.
Hook up and turn the water on.
Plug in the machine and test the valve.
Unplug the power and reinstall the back and the control panel. The back-to-cabinet clips can be snapped back in place easily.
Read less
Water inlet valve controls the water flow into the washer.
Fits some washers in the following series: Kenmore 110; Whirlpool CHW, WFW and YWFW; Maytag CHW, MHN, MHP, MHWE, MHWZ and YMHWE; Amana NFW and YNFW; and Inglis IFW and YIFW.
Also fits some laundry centers in these series: Whirlpool CET and CGT; and Maytag MLE and MLG.
Water inlet valve controls the water flow into the washer.
Fits some washers in the following series: Kenmore 110; Whirlpool CHW, WFW and YWFW; Maytag CHW, MHN, MHP, MHWE, MHWZ and YMHWE; Amana NFW and YNFW; and Inglis IFW and YIFW.
Also fits some laundry centers in these series: Whirlpool CET and CGT; and Maytag MLE and MLG.
What this part fixes:
- Does not dispense fabric softener or detergent
- Leaking
- No hot or cold water
Installation Instructions
Laura from ENGLEWOOD, CO
Washer would fill extremely slowly when on cold water wash resulting in long fill(LF) error code.
The washing machine would only run on the hot water cycle. When trying to use the warm or cold setting, the water would dribble into the drum and result in an LF error code(long fill). I watched a brief video on replacing the water inlet valve which made it really easy to repair. I first turned off the water, disconnected the hoses from t
... Read more
he machine, and opened the top to access the valves. I then disconnected the wires from the valve, removed the water tubes, swapped out the valves and put everything back together. I am not experienced in repair but this was a very easy fix! We decided to replace the single hot water valve and the dual cold water valve since it's an older machine and it works like new again!
Read less
Your dishwasher's performance can make or break your daily kitchen routine. That's when our GE Bypass Drain Connector comes in handy. Essential for every GE dishwasher, this piece is responsible for channeling water from the pump efficiently to the sump collection chamber during the drain cycle. Without this critical connector, your dishwasher may not perform optimally. So, to maintain a smoothly-functioning dishwasher, you should consider giving it regular check-ups and replace this part if needed. And always remember to disconnect your dishwasher from power and wear work gloves before you start working on it for your safety. Why choose our GE Bypass Drain Connector? Because it embodies the trusted quality of GE parts known for reliability, precision, and efficiency. With this in your dishwasher, you're one step closer to bringing back its peak performance?washing dishes like it's brand new again. Choose the GE Bypass Drain Connector. Help your appliance work at its best and bring ease back into your kitchen routine.
Your dishwasher's performance can make or break your daily kitchen routine. That's when our GE Bypass Drain Connector comes in handy. Essential for every GE dishwasher, this piece is responsible for channeling water from the pump efficiently to the sump collection chamber during the drain cycle. Without this critical connector, your dishwasher may not perform optimally. So, to maintain a smoothly-functioning dishwasher, you should consider giving it regular check-ups and replace this part if needed. And always remember to disconnect your dishwasher from power and wear work gloves before you start working on it for your safety. Why choose our GE Bypass Drain Connector? Because it embodies the trusted quality of GE parts known for reliability, precision, and efficiency. With this in your dishwasher, you're one step closer to bringing back its peak performance?washing dishes like it's brand new again. Choose the GE Bypass Drain Connector. Help your appliance work at its best and bring ease back into your kitchen routine.
Installation Instructions
Laura from ENGLEWOOD, CO
Washer would fill extremely slowly when on cold water wash resulting in long fill(LF) error code.
The washing machine would only run on the hot water cycle. When trying to use the warm or cold setting, the water would dribble into the drum and result in an LF error code(long fill). I watched a brief video on replacing the water inlet valve which made it really easy to repair. I first turned off the water, disconnected the hoses from t
... Read more
he machine, and opened the top to access the valves. I then disconnected the wires from the valve, removed the water tubes, swapped out the valves and put everything back together. I am not experienced in repair but this was a very easy fix! We decided to replace the single hot water valve and the dual cold water valve since it's an older machine and it works like new again!
Read less
Discover the reliable and sturdy Water Inlet Valve with Vacuum Break from Whirlpool. This is a genuine OEM component designed to enhance the functionality of select Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, Inglis, and Magic Chef models. Serving as a crucial element for washers, this water inlet valve accurately controls the water flow into your appliance. For safeguarding your appliance's longevity, ensure your model's compatibility with this part prior to ordering as variations in size and shape may occur. Remember to unplug your washer and stop the water supply before initiating the installation of this part. For added precautions, it is advised to wear protective gloves. Keep your machine running at its best with this vital Whirlpool part.
Discover the reliable and sturdy Water Inlet Valve with Vacuum Break from Whirlpool. This is a genuine OEM component designed to enhance the functionality of select Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, Inglis, and Magic Chef models. Serving as a crucial element for washers, this water inlet valve accurately controls the water flow into your appliance. For safeguarding your appliance's longevity, ensure your model's compatibility with this part prior to ordering as variations in size and shape may occur. Remember to unplug your washer and stop the water supply before initiating the installation of this part. For added precautions, it is advised to wear protective gloves. Keep your machine running at its best with this vital Whirlpool part.
Installation Instructions
Robert from GEORGETOWN, KY
Cold water constantly dripping into the washer
Removed the two screws that secured the control panel to top of washer. Removed panel by pulling if forward and rotateing it upward. Removed the two clips that secure the back panel to the washer body. Rotated body forward. Disconnected plug from water inlet valve remove valve and replace with new one. Reverse the process of disassembly.