Inglis Washer Latches

Inglis Appliance Parts
Shop By Part Type

Popular Inglis Washer Latches

Your Price
$46.17
  In Stock
Lid Latch Assembly
★★★★★
★★★★★
(28)
PartSelect Number PS3497627
Manufacturer Part Number W10404050
The point of the lid switch is for the tub to stop spinning when the washer lid is opened. It is a safety precaution just in case someone decides to stick their hand inside the washer while the tub is spinning.
Fixes these symptoms
  • Lid or door will not open
  • Lid or door won’t close
  • Pumps but will not spin
  • See more...
Installation Instructions
William from Wakefield, RI
Defective lid latch - Cabrio Washer
The instructions that came with the part were worthless. Essentially, unplug, put in new part, plug it back in. I spent a considerable amount of time on the internet and finally found a video showing how to open the top. Unlike other models, it is held down by clamps in the back rather than clips in the front. Once finding this information the installation was simple. Remove the clamps and the back of the console, slide the top forward and lift, remove and replace the lock and reassemble. You don't even have to remove the hoses. Read more...
Your Price
$9.91
  In Stock
Door Strike/Hook
★★★★★
★★★★★
(11)
PartSelect Number PS11746261
Manufacturer Part Number WP8540221
Used to help make the door stay closed. Sold individually.
Fixes these symptoms
  • Door won’t close
  • Leaking
  • Lid or door will not open
  • See more...
Installation Instructions
david from st petersburg, FL
the strike hook was broken
replacing the hook was simple 2 torx screws. the latch assembly seemed ok I could hear it trying to latch the hook so i just replace the broken hook. Read more...
Your Price
$108.01
  In Stock
Door Lock Latch
★★★★★
★★★★★
(17)
PartSelect Number PS11745016
Manufacturer Part Number WP8182634
This part is used on front load washers and includes the interlock switch assembly.
Fixes these symptoms
  • Door latch failure
  • Lid or door will not open
  • Lid or door won’t close
  • See more...
Installation Instructions
James from Vilonia, AR
front load washer latch replacement
1. remove the three screws from the top backside of the top panel
2. push the top panel to the rear 1/8 to 1/4 inch
3. lift/rotate top panel from rear to front, set aside.
4. remove the three wire connectors from latch.
5. use #15 Torx to remove the three screws from the latch.
6. remove and replace part using top opening.
7. reverse order to finish.
Read more...
Your Price
$31.96
  In Stock
Door Lever
★★★★★
★★★★★
(11)
PartSelect Number PS11741552
Manufacturer Part Number WP34001260
Also known as a door strike.
Fixes these symptoms
  • Lid or door will not open
  • Lid or door won’t close
  • Will Not Start
  • See more...
Installation Instructions
Leon from North Platte, NE
door latch split
replaced door latch but door would not close had to remove latch assembly and reset the latch in the latch assembly. To reset latch in latch assembly you remove the black plastic only on latch assembly then press the spring down with thumb move the black plastic catch back to the latch position. when you remove the black plastic there is four metal switchs and one spring that you have to pay attention too so remove very carefully. Read more...
Your Price
$29.87
  In Stock
Lid Latch Strike
★★★★★
★★★★★
(6)
PartSelect Number PS11750882
Manufacturer Part Number WPW10240513
This part is the replacement lid latch or latch assembly for your top-load washer. The lid latch holds your washer door closed, and allows the washer to run its cycle. If the lid latch is damaged, your washer door may not close properly and you may not be able to run your washer. The latch is found under the lid and can be screwed out and replaced. You will need a Phillips-head screwdriver for this repair. This part is sold individually and is and OEM part from the manufacturer.
Fixes these symptoms
  • Lid or door will not open
  • Lid or door won’t close
  • Pumps but will not spin
  • See more...
Installation Instructions
John from Hale Center, Texas, TX
lid would not lock, washer would not run...
Removed old striker ( 2 Phillips head screws ) replaced with new striker with the 2 screws and was done, easy fix... Read more...
Your Price
$19.34
  In Stock
STRIKE
★★★★★
★★★★★
(5)
PartSelect Number PS11726338
Manufacturer Part Number W10837741
Fixes these symptoms
Installation Instructions
Anna from TAWAS CITY, MI
Lid strike broke
Removed old one (2 screws) slid in place and screwed in. Read more...
Your Price
$129.71
  In Stock
Door Lock Latch
★★★★★
★★★★★
(3)
PartSelect Number PS11751211
Manufacturer Part Number WPW10253483
This part ensures that your door stays locked while the machine is running.
Fixes these symptoms
  • Lid or door will not open
  • Lid or door won’t close
  • Will Not Start
  • See more...
Installation Instructions
Carlton from Greer, SC
Door latch module was defective
This model is a front-loading washer. The spring loaded retainer for the front of the boot must be removed, then the boot can moved to the side exposing the module. Remove the two screws holding the model, pull the model out, remove the three electrical plugs, then reverse this procedure to install new module. Read more...
Your Price
$5.67
  In Stock
Lid Strike
★★★★★
★★★★★
(6)
PartSelect Number PS11741871
Manufacturer Part Number WP358684
This part is used to activate the lid switch when the lid opens/closes.
Fixes these symptoms
  • Pumps but will not spin
  • Timer will not advance
  • Will not agitate
  • See more...
Installation Instructions
Fred from Midlothian, VA
Washing Machine kept cutting off mid-cycle
I had to remove the washing machine from the laundry room (our laundry room is pretty small).

I read the do-it-yourself explanation posted by Paul From Glendale CA and followed his instructions.

1. Unplugged the Washer and disconnected the hoses, so I could slide the washer into the kitchen.

2- Unfastened the two screws in the front lower corners of the controls panel and tilted is back. Unfastened the old lid-switch wiring from the control panel.

3. Remove the clips at the two corners under the control panel. I rotated the cover forward to clear it from the back and lifted it off and set it off to the side.

4. While I had the Washer disassembled I vacuumed out all the accumulation of dust, etc.

5. Removed the lid switch and unfastened the ground wire.

6. Installed the new switch and reassembled the Washer.

7. I did not read Paul's reassembly instructions closely enough. The front flange of the cover goes UNDER the steel frame on the washer. I spent 30 minutes trying to get the cover on, then finally figured that out on my own. Once I got the flange under the frame, it took about five minutes to get the cover on, the clips in and the control panel back into positions and reassembled.

The entire process is not particularly difficult. Had I read the "UNDER the frame" part earlier, the entire repair would have taken no more than 45 minutes.

Having another person to help reinstall the cover would be helpful. The cover is not heavy but it is a little awkward to handle and having another person to help line up the back cover, etc. will make the reassembly even easier.
Read more...
Your Price
$5.67
  In Stock
Bezel
★★★★★
★★★★★
(1)
PartSelect Number PS11754116
Manufacturer Part Number WPW10392041
Fixes these symptoms

Related Parts