Lid Strike WP358684 | Official Whirlpool Part | Fast Shipping | PartSelect
Lid Strike – Part Number: WP358684
( Grid squares measure 1x1 inch )
Lid Strike – Part Number: WP358684 Lid Strike – Part Number: WP358684 Lid Strike – Part Number: WP358684 https://partselectcom.azureedge.net/Schematics/Maytag/YQVV2IYF.gif

Lid Strike

PartSelect Number PS11741871

Manufacturer Part Number WP358684

Manufactured by Whirlpool

Product Description

Lid Strike Specifications

This part is used to activate the lid switch when the lid opens/closes.

How Buying OEM Parts Can Save You Time and Money

Troubleshooting

This part fixes the following symptoms:

Will not drain | Will Not Start | Timer will not advance | Will not agitate

This part works with the following products:

Washer, Washer Dryer Combo.

This part works with the following brands:

Whirlpool, Kenmore, KitchenAid, Roper, Estate, Maytag, Inglis, Crosley, Amana.

Part # WP358684 replaces these:

357913, 358684, AP6008731.
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
2 questions answered by our experts.
Sort by:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Part Videos

Replacing your Whirlpool Washer Lid Strike

Customer Repair Stories
Average Repair Rating: 3.3 / 5.0, 5 reviews What's this?
Sort by:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Fred from Midlothian, VA
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers, Wrench (Adjustable)
Parts Used:
WP358684, 285671
Washing Machine kept cutting off mid-cycle
I had to remove the washing machine from the laundry room (our laundry room is pretty small).

I read the do-it-yourself explanation posted by Paul From Glendale CA and followed his instructions.

1. Unplugged the Washer and disconnected the hoses, so I could slide the washer into the kitchen.

2- Unfastened the two screws in the front lower corners of the controls panel and tilted is back. Unfastened the old lid-switch wiring from the control panel.

3. Remove the clips at the two corners under the control panel. I rotated the cover forward to clear it from the back and lifted it off and set it off to the side.

4. While I had the Washer disassembled I vacuumed out all the accumulation of dust, etc.

5. Removed the lid switch and unfastened the ground wire.

6. Installed the new switch and reassembled the Washer.

7. I did not read Paul's reassembly instructions closely enough. The front flange of the cover goes UNDER the steel frame on the washer. I spent 30 minutes trying to get the cover on, then finally figured that out on my own. Once I got the flange under the frame, it took about five minutes to get the cover on, the clips in and the control panel back into positions and reassembled.

The entire process is not particularly difficult. Had I read the "UNDER the frame" part earlier, the entire repair would have taken no more than 45 minutes.

Having another person to help reinstall the cover would be helpful. The cover is not heavy but it is a little awkward to handle and having another person to help line up the back cover, etc. will make the reassembly even easier.
149 of 172 people found this instruction helpful.
Was this instruction helpful to you?
Kenneth from El Paso, TX
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Pliers, Screw drivers, Wrench (Adjustable), Wrench set
Parts Used:
WP358684, WP3355806
Machine would stop when finished rinse cycle and wouldn't spin or drain.
I replaced the Lid Switch and the unit works fine. I also cleaned up some other issues in the unit which took about half the time.
56 of 104 people found this instruction helpful.
Was this instruction helpful to you?
LARRY from LUCERNE, CA
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Parts Used:
3949247V, WP358684
shut off before finished
i knew the lid sw. must be bad and had a new one in hand, but when i remove the sw. ( near the lid ) i found the wires going back to where i could not reach. was not sure how to get at them so i repaired the sw. with tape untill i could find how to get at the wire end. after reading more in this repair area i know that i need to remove the control panel which is easy to do. next time i will read all i can on repairs in this section!!
16 of 21 people found this instruction helpful.
Was this instruction helpful to you?
Matt from Sussex, WI
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Screw drivers, Socket set
Parts Used:
3949247V, WP358684
Washer did not spin.
First I removed the two screws on the back side of the switch panel and tilted it back to expose the controls. I then pryed up the top of the washer to expose the lid switch. This was a mistake because I damaged the clips and bent the metal frame. Anyway after that I unlatched the lid switch on the top side, pulled it through the bottom, removed two screws holding the lid switch in place and replaced the switch and lid switch strike. Because I wrecked the machine top I had no alternative but to drill two holes from the top and put two screws in to hold the top down. It's ugly but it works.
The best part of all this is I received the part so fast that I was able to keep up the pace of doing laundry with no interruption. Thanks for being so reliable and quick to deliver. I already told many people about your service!
15 of 18 people found this instruction helpful.
Was this instruction helpful to you?
Anthony from PITTSTON, PA
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers, Screw drivers
Parts Used:
WP358684, 3949247V
Washer would not start, when started wouldn't stay running.
I found the problem when I leaned on the lid while it started and that pressure kept it running. By placing detergent bottles on the right side of the lid I was able to walk away. I then bought the lid switch and lid strike after seeing it is a common problem. I watched the video and followed it almost step by step. First I unplugged the washer but didn't unhook the hose (only because I didn't have to move the washer) then I unscrewed the two screws holding the control panel, flipped it over, unplugged the lid switch connector, removed the clips holding the washer body on and tilted the body far enough forward to work on it. I replaced the switch as was done in the video and put the washer back together opposite the way I took it apart.
1 person found this instruction helpful.
Was this instruction helpful to you?
Customer Reviews
Average Rating:
6 Reviews
4
out of 5
Filter By Rating:
  • 5 Stars
    3
  • 4 Stars
    2
  • 3 Stars
    0
  • 2 Stars
    0
  • 1 Stars
    1
Sort by:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Model Cross Reference

This part works with the following models:

PartSelect Number: PS11741871
Manufacturer Part Number: WP358684
Brand
Model Number
Description
Kenmore
110088732791
Washer Dryer Combo
Kenmore
1101820299
Washer Dryer Combo - WASHER DRYER LAUNDRY SYSTEM
Kenmore
11020112000
Washer
Kenmore
1102011200A
Washer
Kenmore
11020132000
Washer
Kenmore
11020132001
Washer
Kenmore
11020172000
Washer
Kenmore
11020172001
Washer
Kenmore
11020272000
Washer
Kenmore
11020272001
Washer
Kenmore
11026051690
Washer
Kenmore
11026058590
Washer - Kenmore Washing Machine Model 110.26058590 (11026058590, 110 26058590) Parts
Kenmore
11026058690
Washer
Kenmore
11026071690
Washer
Kenmore
11026071691
Washer
Kenmore
11026182029A
Washer Dryer Combo - THIN-TWIN (WASHER/DRYER)
Kenmore
11027112600
Washer
Kenmore
11027172600
Washer
Kenmore
11027172601
Washer
Kenmore
11027272600
Washer
Kenmore
1102870090
Washer
Kenmore
11029012990
Washer
Kenmore
11029032990
Washer
Kenmore
11029072990
Washer
Kenmore
1102970093
Washer
Kenmore
11042182200
Washer
Kenmore
11042182201
Washer
Kenmore
11042722200
Washer
Kenmore
11042722201
Washer
Kenmore
1104812791
Washer - Kenmore Washing Machine Model 110.4812791 (1104812791, 110 4812791) Parts