Refrigerator Valves

Shop By Brand

Popular Refrigerator Valves

Your Price
$67.83
  In Stock
Refrigerator Water Inlet Valve
★★★★★
★★★★★
(79)
PartSelect Number PS7784018
Manufacturer Part Number 242252702
The function of the Refrigerator Water Inlet Valve (Triple Solenoid Water-Valve, Water Valve, Water Inlet Valve, Refrigerator Water Inlet Valve Assembly) is to release water from the supply line when activated, and send it through to your water dispenser or ice maker in your refrigerator. The water inlet valve is located at the back of the refrigerator, and connects to the water supply. The valve can break from material fatigue or normal use. If your water inlet valve is malfunctioning, you could be getting a lack of water to the inside of your refrigerator. Your ice maker may not produce cubes or your water dispenser may not work. The water inlet valve must be replaced if the solenoids no longer have continuity or the valve has internal blockage. This valve measures approximately 7 inches long and 4.5 inches wide, and is constructed of plastic and metal. It comes in blue, and includes the valve and mounting bracket.
Fixes these symptoms
  • Ice maker dispenses too little ice
  • Ice maker not making ice
  • Ice maker won’t dispense ice
  • See more...
Installation Instructions
Jose from Alexandria, VA
water leaking out of refrigerator
In my specific appliance the water valve is located in the bottom right hand corner looking at it from the back. To get to it I remove the thin layer of cardboard the covers the back of the fridge. I then proceeded to disconnect the 1/4" copper tubing which is the water feed coming out of the wall. Then I removed the screws that hold the valve assembly in place. I took the water valve out and removed the electrical connections as well as the plastic tubing which feed the water dispenser and the ice maker. To install the new water valve it was just a matter of reversing steps. Read more...
Your Price
$87.26
  On Order
Water Inlet Valve
★★★★★
★★★★★
(56)
PartSelect Number PS3497634
Manufacturer Part Number W10408179
The water inlet valve (Refrigerator Water Inlet Valve Kit) provides water for the ice maker and water dispenser. This part is located at the back of the refrigerator, and connects to the water supply. If your water inlet valve is malfunctioning, you could be getting a lack of water to the inside of your refrigerator. Your ice maker may not produce cubes or your water dispenser may not work. This breakage can occur from material fatigue or normal use, and is a sign the part should be replaced soon. The water inlet valve must be replaced if the solenoids no longer have continuity or the valve has internal blockage. The part measures approximately 6.5 inches long and 3 inches wide and is constructed of plastic and metal. It comes in blue/green/red.
Fixes these symptoms
  • Ice maker dispenses too little ice
  • Ice maker not making ice
  • Ice maker won’t dispense ice
  • See more...
Installation Instructions
GLENN from ORLAND PARK, IL
was not making ice
take out ice bucket, just loosen the top 2 screws, remove the bottom screw, slide ice maker up & out, srewdriver to release wiring harness clip, reverse to put back in. was very simple. did not install water inlet kit yet. water under fridge stopped after i changed the ice maker. Read more...
Your Price
$43.20
  In Stock
Water Inlet Valve
★★★★★
★★★★★
(15)
PartSelect Number PS7784017
Manufacturer Part Number 242252603
If you notice that the ice maker in your refrigerator is leaking or is not making or dispensing ice, you may need to replace the water inlet valve. When energized, the water inlet valve releases water from the supply line into the ice mold. The water inlet valve is in the back of your refrigerator so you will need to pull the fridge out from the wall before completing this repair. To complete this job, you will need a 1/2 inch wrench, a 1/4 inch nut driver and a utility knife. If your old inlet valve has a screw-in fitting, you may need to simply cut the end of the hose to fit in the new part. Be sure to disconnect both the water and power supply from the refrigerator prior to beginning this repair.
Fixes these symptoms
  • Ice maker not making ice
  • Ice maker won’t dispense ice
  • Leaking
  • See more...
Installation Instructions
Orville from Garland, TX
Was not filling the ice tray full.
I had put in a new ice maker and it still had the problem, (I needed the Ice maker anyway) I installed the vale and while I was at it I put a five year filter on the water line that went from the value to the Ice maker, it took less than one hours, the ice is making like it did when it was new, I could not be more please at theis time. Thanks for your Interest. God bless. Read more...
Your Price
$87.14
  On Order
Dual Inlet Water Valve
★★★★★
★★★★★
(69)
PartSelect Number PS304374
Manufacturer Part Number WR57X10032
This water inlet valve (Refrigerator Water Inlet Valve Assembly) supplies water to the ice maker and the water dispenser in your refrigerator. It is located at the back of the fridge, beneath the bottom panel. It is connected directly to 2 water supplies, a wiring harness, and your inlet water tube. This part is located at the back of the fridge, beneath the bottom panel. It is connected directly to 2 water supplies, a wiring harness, and your inlet water tube. Minerals and sediments can build up over time and cause a blockage in your inlet valve. They can also cause the valve to stick open, leading to an overflow of water. If this part is malfunctioning, water flow to your appliance could be compromised. Check for small ice cubes or a lack of ice cubes/water, as this is an obvious sign the part is damaged. The water inlet valve must be replaced if the solenoids no longer have continuity or the valve has internal blockage. Test your water inlet valve with a multimeter. You can test both the water dispenser side and the ice maker side. The part measures approximately 3 inches long and 2.75 inches wide and is constructed of plastic and metal. This replacement part features 1 dual inlet water valve with quick connections. It also has 1/4 and 5/16 John Guest fittings for the outlet lines and a 1/4 compression fitting for the inlet line.
Fixes these symptoms
  • Ice maker not making ice
  • Ice maker won’t dispense ice
  • Leaking
  • See more...
Installation Instructions
ralph from bristow, VA
Refrigertor water dispenser not working BUT ice machine is working
The very first symptom here is important! The door water dispenser is not working but the ice macine is working. You may only have a frozen water tube in the door so do the following before diagnosing that your solenoid valve is bad: 1) the tube usually runs under the front of the refrigerator and usually has a quick disconnect. Undo the connection and press the dispenser. If water comes out of the tube you have a frozen or blocked tube in the door. 2) Immediately adjust the temperature in the freezer and warm the freezer compartment as much as you can without destroying the freezer contents. Wait 24 hours. This will usually unfreeze the line. Do not waste your time with a hair dryer. NOW, if this doesn't work and you are convinced you need to order and replace the solenoid, follow these steps. Assemble your tools first. I needed a good ratchet set and a screwdriver. A shop towel is helpful for spilled water. A light is handy. Pull out the refreigerator to gain access to the rear of the unit. Unplug the power and close the water valve (older homes, you may need to actually shut the house water supply). Remove the screws which hold the cover over the lower half of the refrigerator. On the left you will see the solenoid. It's always good to see that your new part matches the one you feel needs replaced. They may not match perfectly due to changing design but they should be very similar. One screw holds this part in place and access is very simple. Now simply unplug the electrical connections. In my case, one blue "blade" type connection (powering the water) and one red "blade" type connection powering the ice maker. They are not the same size and this coupled with the coloring means you will not accidently switch them. pull the tubes clear of the solenoid. This is simple and needs no explantion. Grab your new solenoid and reattach both the electrical and water lines (two, remember, ice maker and drink dispencer). Replace the single screw. Re-attach the rear, lower refrigerator cover and go to the front of the unit to check the water. You can listen carefully and hear the power engage from the new part bringing you water. Clean up, replace the refrigerator back to its place and look really tired when your wife sees that you worked "so hard"! You probably saved at least $50-$80 from a service call which can now be used to take the family to dinner after your "exhausting" 15 minute workout of removing about 10 screws and wheeling the unit in and out of place. Writing this article took longer! My 4 year old worked harder holding the flash light! Read more...
Your Price
$110.10
  On Order
Water Inlet Valve - 4 Coil
★★★★★
★★★★★
(3)
PartSelect Number PS7321353
Manufacturer Part Number 242253002
The water inlet valve supplies water to the refrigerator ice maker and water dispenser. This part works with the following brands: Frigidaire, White Westinghouse, Kelvinator, Gibson, Kenmore, Sears, Tappan, & Electrolux. Possible Repair Solution For: Leaking water, water will not dispense, ice maker does not make ice, ice maker does not dispense ice. This is an authentic water inlet valve (4 coil), which works with refrigerators.
Fixes these symptoms
  • Ice maker not making ice
  • Not dispensing water
  • See more...
Installation Instructions
Neville from LITHONIA, GA
Not making ice in both ice maker or dispensing water
To confirm my diagnosis I first replace the filter still no water flow.
Check water supply from the wall valve: ok
Remove the entire inlet valve assembly and sit it over a small bucket.
Disconnect the tubing from the bottom of the 1st selenide valve: this is the one leading to the filter.
Place cup under water dispenser and activate dispenser. No water discharge from inlet valve confirm valve is bad.
Install the new valve matching the colored tubing with the color on each inlet valve.
Re-connect the water supply place container under water dispenser and activate: There will be a large gush of air then water. Dispense aprox 1 gallon of water to confirm all the air is purged from the system. Your refrigerator is now back to dispensing water and making ice.
Good luck everyone - Neville
Read more...
Your Price
$56.49
  In Stock
Dual Inlet Water Valve
★★★★★
★★★★★
(15)
PartSelect Number PS901314
Manufacturer Part Number WR57X10051
This valve comes with 1/4" compression inlet. NOTE: This part comes with new quick connections. To install - cut retaining nuts off of existing plastic water lines and gently push them into new valve. To remove - depress ring that the tube slides into.
Fixes these symptoms
  • Ice maker not making ice
  • Ice maker won’t dispense ice
  • Leaking
  • See more...
Installation Instructions
anthony from thornton, CO
Cracked housing on the vaave
1. Turn off water supply, and electrical ( unplug it) to fridge.
2. Remove water line to valve. Watch for water to pour out of the line. Have a towel handy.
3. Remove the cardboard cover on the bottom of the fridge.
4. Remove the screws that hold the valve in place.
5. Remove the valve, be careful the waterlines are still attached.
6. Place a towel under valve to catch any water that leaks out from water lines.
7. Remove electrical lines, make sure to mark which went where. One is for the ice, and one is for the water. Make sure the power is off, there is 120 volts present at those connections.
- now my waterlines attached using a compression type fitting. The new valve I got used just a push in type of attachment. But, easy enough I just removed the pieces for the compression and the waterlines pushed right in and worked fine.
- the mounting harness for the valve was alittle different but the parts I need were in the right location and she fit in fine.
8. Attach water lines. They are different sizes so you can't get those mixed up.
9. Attach electrical lines.
- the new valve came with adaptors for my electrical connection. Just snapped them on and kept on going.
10. turn on watersupply for fridge. Plug it back in.
11. Test for leaks, and proper operation. ie. When you push the water does the water valve open?
12. Unplug fridge
13. Now is a good time to clean out any dust or dirt that has accumallated in under around your fridge.
14. reassemble, valve, then cover. move fridge back into place.
15. Plug fridge back in.
16. Take a clean glass.
17. Fill with water from the front.
18. Take full glass of water and go watch tv. You've earned it, and saved yourself probably $100.00 in labor costs. Good Job.
Read more...
Your Price
$71.14
  In Stock
Refrigerator Single Water Inlet Valve
★★★★★
★★★★★
(13)
PartSelect Number PS11740365
Manufacturer Part Number WP2315576
The single water inlet valve, also known as a water solenoid valve, is used for refrigerators. This part is a solenoid-operated switch that releases water from the supply line to the water valve and into the icemaker mold when activated. If your icemaker is making small cubes, does not dispense ice or water, or leaks, this replacement could solve the issue. The tools needed for this repair are a 1/4 inch nut driver and a utility knife. Refer to the diagram provided by the manufacturer for further instructions. As a safety precaution, remember to unplug your dryer from the power source.
Fixes these symptoms
  • Ice maker not making ice
  • Ice maker won’t dispense ice
  • Leaking
  • See more...
Installation Instructions
Robert from Abingdon, MD
No water feed to icemaker
To troubleshoot - Check water supply to valve. It f that's good - remove back plate, remove water valve reconnect inlet line, disconnect electrical connector, place valve over a pan with outlet fitting disconnected, temporarily connect 110 VAC with clipleads to water valve solenoid. No water flow means valve is not opening. To install new valve, connect outlet line, and wiring connector, then insert in cabinet and install 2 screws, reinstall back plate, connect water inlet line. Read more...
Your Price
$49.39
  In Stock
Single Outlet Valve Kit
★★★★★
★★★★★
(20)
PartSelect Number PS304375
Manufacturer Part Number WR57X10033
The water inlet valve on your refrigerator allows water to enter the ice maker and water dispenser. If your ice maker or water dispenser is not functioning properly, or you notice a leak, you may need to replace the single outlet valve. This single outlet valve has 1/4-inch compressions fittings and is intended for use with refrigerators that make crescent-shaped ice cubes. As per the manufacturer, this valve has a new quick connection. You must cut the retaining nut off your current plastic water line, and gently push it into the new valve. Be sure to disconnect the water and power sources from the refrigerator before you begin this repair.
Fixes these symptoms
  • Ice maker not making ice
  • Ice maker won’t dispense ice
  • Leaking
  • See more...
Installation Instructions
Michael from Bradenton, FL
ice maker not working properly and door seal worn
Two screws held the icemaker on. You do not even have to take them all the way out to remove the IM. Replacement of the water valve was just as easy except they (parts manufacturer) updated the flange nut with a compression fitting and it took me a minute looking at it before I realize what was going on. The door seal could not be easier, no tools just a few minutes of time Read more...
Your Price
$80.65
  In Stock
Dual Water Valve
★★★★★
★★★★★
(13)
PartSelect Number PS11743618
Manufacturer Part Number WP67005154
This part, when activated, releases water from the supply line into the ice mold. This water inlet valve is for refrigerators. Water inlet valve supplies water to the refrigerator ice maker and water dispenser. Safely store any food that could deteriorate while the power is off and unplug the refrigerator before installing this part. Wear work gloves to protect your hands.
Fixes these symptoms
  • Ice maker not making ice
  • Ice maker won’t dispense ice
  • Leaking
  • See more...
Installation Instructions
Salvador from McAllen, TX
Trickle to no water from dispenser / very little ice
Shutoff water and turn off fridge. Remove the main water hose from the fridge with pliers, then remove back bottom plate of fridge where the hose was at (about 5 screws) in order to disconnect the hoses going into the valve by pushing in on the plastic colored fastener(blue & white) while pulling on the hose at the same time. Do this for each of the hoses. Then disconnect the wires from the valve and unscrew the valve(1 screw) from the back plate. Replace with new valve which comes with brand new fasteners for the hoses so all you have to do is insert the hoses in the valve and reverse the above process to install the valve. Read more...
Your Price
$100.48
  On Order
Dual Water Inlet Valve
★★★★★
★★★★★
(13)
PartSelect Number PS11743697
Manufacturer Part Number WP67006531
This is a dual water inlet valve for your refrigerator/freezer. The water inlet valve is a solenoid-operated switch that, when activated, releases water from the supply line into the water valve. The liquid will then be sent to the compact icemaker mold and to the water line. You will need to replace this part if you are experiencing leaking, or your appliance is not properly dispensing water or ice. This model is blue/green in color and is roughly 3 inches wide, 5 inches long, and 4 inches thick.
Fixes these symptoms
  • Ice maker not making ice
  • Leaking
  • Not dispensing water
  • See more...
Installation Instructions
JIM from Greeley, CO
Refrigerator sat in storage in sub zero weather, water in Dual Water Inlet Valve froze, cracking valve.
This is the 2nd time I have used PartSelect, and this experience was as pleasant as the 1st. The exploded-view diagrams make parts identification very easy; and the photo of the actual part is such a great idea, it allows you to verify what you need. I also got my part (cross country, in 3 days)

Repair Procedure: Shut off water supply. It may be easier to work if you disconnect the water supply tube, but it is not required. On the backside of the refrigerator, remove the bottom, black plastic protection panel. You will need a nut driver or battery-powered screw driver with a 3/8" socket tip on it. Next, remove the black metal panel that holds the water inlet valve in place. Remove screws with a nut driver. 1st remove the two flat-pin power connectors. (They are different sizes and color-coded, so there is no room for making a re-hookup mistake). Then proceed to remove the hoses. The hoses are pressure-lock tubing, so push the plastic disk in or down where the tube goes into the main body of the valve. Do this for all three hoses (tubes). Switch water valves and reverse the procedure. **Be certain that the tubes are pushed back in as far as they can go; if you do not re-seat the tubes, the pressure from the water going back in the valve, will blow the tubes right out the valve (ask me how I know this!). Once reassembled, turn the water back on slowly. Make sure you turn the water supply valve all the way open, it seats itself internally when you do and is less prone to drip leaks. That's it! (As a former kitchen remodeler, I find this a great DIY project).
Read more...

Brands