EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

Frigidaire Refrigerator Valves

Popular Frigidaire Refrigerator Valves

This refrigerator water inlet valve assembly controls water flow to the ice maker and door dispenser. Its three electric coils open and close separate water paths, sending water where it is needed. A leaking or blocked valve may cause weak dispenser flow, small ice cubes, slow ice production, or water pooling behind the refrigerator. Replacing a faulty assembly helps restore steady water flow and stops unwanted filling between uses. Unplug the refrigerator and shut off the water supply before replacing the valve. This is an OEM part sourced directly from the manufacturer.
This refrigerator water inlet valve assembly controls water flow to the ice maker and door dispenser. Its three electric coils open and close separate water paths, sending water where it is needed. A leaking or blocked valve may cause weak dispenser flow, small ice cubes, slow ice production, or water pooling behind the refrigerator. Replacing a faulty assembly helps restore steady water flow and stops unwanted filling between uses. Unplug the refrigerator and shut off the water supply before replacing the valve. This is an OEM part sourced directly from the manufacturer.
What this part fixes:
  • Ice maker dispenses too little ice
  • Ice maker not making ice
  • Ice maker won’t dispense ice
Installation Instructions
Jose from Alexandria, VA
water leaking out of refrigerator
In my specific appliance the water valve is located in the bottom right hand corner looking at it from the back. To get to it I remove the thin layer of cardboard the covers the back of the fridge. I then proceeded to disconnect the 1/4" copper tubing which is the water feed coming out of the wall. Then I removed the screws that hold the valve assembly in place. I took the water valve out and removed the electrical connections as well as the plastic tubing which feed the water dispenser and the ice maker. To install the new water valve it was just a matter of reversing steps.
This water inlet valve is usually located behind the lower kickplate panel in either the right or left corner of the dishwasher. The attaching solenoids on the valve open and close according to the desired amount of water needed. The water inlet valve on your dishwasher supplies water to the dishwasher. If your dishwasher is leaking because it has overflowed, the water inlet valve may be the cause. If your dishwasher continues to fill above the heating element, try opening the door latch to see if it stops filling. If it continues to fill, you have a defective inlet valve that will need to be replaced.
This water inlet valve is usually located behind the lower kickplate panel in either the right or left corner of the dishwasher. The attaching solenoids on the valve open and close according to the desired amount of water needed. The water inlet valve on your dishwasher supplies water to the dishwasher. If your dishwasher is leaking because it has overflowed, the water inlet valve may be the cause. If your dishwasher continues to fill above the heating element, try opening the door latch to see if it stops filling. If it continues to fill, you have a defective inlet valve that will need to be replaced.
What this part fixes:
  • Leaking
  • Noisy
  • Not cleaning dishes properly
Installation Instructions
CHRIS from ROANOKE, VA
Water leaking from Inlet Valve
Remove the bottom cover plate. Disconnect the water inlet and black rubber hose. Remove 2 mounting screws. Pull out electrical connector. Reverse order. Be sure to get the brass inlet connector really tight so it won't leak. I did the final tightning after the part is mounted. Not a bad repair at all. The only problem was that it leaked in the first place and messed up my subfloor and laminate flooring.
This refrigerator water inlet valve controls the flow of household water into the ice maker or water dispenser. It opens when water is needed and closes to stop the flow. A worn or damaged valve may cause slow filling, reduced ice production, dripping, or leaks near the back of the refrigerator. Replacing a faulty valve helps restore proper water flow and keeps the supply shut off between uses. Unplug the refrigerator and turn off the water supply before starting the repair. This is an OEM part sourced directly from the manufacturer.
This refrigerator water inlet valve controls the flow of household water into the ice maker or water dispenser. It opens when water is needed and closes to stop the flow. A worn or damaged valve may cause slow filling, reduced ice production, dripping, or leaks near the back of the refrigerator. Replacing a faulty valve helps restore proper water flow and keeps the supply shut off between uses. Unplug the refrigerator and turn off the water supply before starting the repair. This is an OEM part sourced directly from the manufacturer.
What this part fixes:
  • Ice maker not making ice
  • Ice maker won’t dispense ice
  • Leaking
Installation Instructions
Orville from Garland, TX
Was not filling the ice tray full.
I had put in a new ice maker and it still had the problem, (I needed the Ice maker anyway) I installed the vale and while I was at it I put a five year filter on the water line that went from the value to the Ice maker, it took less than one hours, the ice is making like it did when it was new, I could not be more please at theis time. Thanks for your Interest. God bless.
This refrigerator water inlet valve assembly controls water flow to the dispenser and ice maker through four electrically operated solenoids. It opens the required water passages when filling or dispensing is requested, then closes them to stop the flow. A cracked housing or faulty valve may cause leaks, slow dispensing, poor ice maker filling, or unwanted dripping into the ice tray. Replacing a failed assembly helps restore controlled water delivery and reliable shutoff, supporting normal ice production and everyday use of the water dispenser. This is an OEM part sourced directly from the manufacturer.
This refrigerator water inlet valve assembly controls water flow to the dispenser and ice maker through four electrically operated solenoids. It opens the required water passages when filling or dispensing is requested, then closes them to stop the flow. A cracked housing or faulty valve may cause leaks, slow dispensing, poor ice maker filling, or unwanted dripping into the ice tray. Replacing a failed assembly helps restore controlled water delivery and reliable shutoff, supporting normal ice production and everyday use of the water dispenser. This is an OEM part sourced directly from the manufacturer.
What this part fixes:
  • Ice maker not making ice
  • Ice maker won’t dispense ice
  • Leaking
Installation Instructions
Neville from LITHONIA, GA
Not making ice in both ice maker or dispensing water
To confirm my diagnosis I first replace the filter still no water flow.
Check water supply from the wall valve: ok
Remove the entire inlet valve assembly and sit it over a small bucket.
Disconnect the tubing from the bottom of the 1st selenide valve: this is the one leading to the filter.
Place cup under water dispenser and activate dispenser. No water discharge from inlet valve confirm valve is bad.
Install the new valve matching the colored tubing with the color on each inlet valve.
Re-connect the water supply place container under water dispenser and activate: There will be a large gush of air then water. Dispense aprox 1 gallon of water to confirm all the air is purged from the system. Your refrigerator is now back to dispensing water and making ice.
Good luck everyone - Neville
This valve has a 1/4" compression inlet.
This valve has a 1/4" compression inlet.
What this part fixes:
  • Ice maker not making ice
  • Leaking
  • Not dispensing water
Installation Instructions
Billy from Newport News, VA
no water for ice-maker or cold water
Unplugged refrig and shut off water supply. Removed cardboard backing on back of refrig. Then removed water lines and power plug from old water valve. Removed screws holding water valve on refrig chassis. Attached water lines and power plug to new water valve. Then repeated the above steps in reverse order. Took a max of 30 mins to install the water valve and worked properly when plugged in refrig and turned water supply on.
Original Equipment Manufacturer

MAKE THIS REPAIR A GUARANTEED WIN

OVER 2 MILLION PARTS TO ENSURE VICTORY

$99.39
In Stock
Water to the refrigerators dispenser and ice maker is controlled by this OEM inlet valve. Confirm fit against your refrigerators model number before buying.
Water to the refrigerators dispenser and ice maker is controlled by this OEM inlet valve. Confirm fit against your refrigerators model number before buying.
$106.06
In Stock
No water from the dispenser or ice maker may point to a faulty inlet valve. This OEM dual inlet valve controls water flow to both. Confirm it is compatible with your refrigerator model, and check that water pressure is at least 20 psi for the valve to shut off properly.
No water from the dispenser or ice maker may point to a faulty inlet valve. This OEM dual inlet valve controls water flow to both. Confirm it is compatible with your refrigerator model, and check that water pressure is at least 20 psi for the valve to shut off properly.
$66.99
In Stock
This dual water inlet valve is typically located in the back of the refrigerator. It comes with the mounting bracket.
This dual water inlet valve is typically located in the back of the refrigerator. It comes with the mounting bracket.
What this part fixes:
  • Ice maker not making ice
  • Leaking
  • Not dispensing water
Installation Instructions
robert from Edmonds, WA
water dispensor inoperative
the system has two dual valves. 1 for water, 1 for ice maker. valve 1 feeds valve 2 via water filter. Voltage to operate both valves was present when water dispensor switch was activated. Both valves are on bottom backside of fridge in opposite corners. Problem was valve plunger was stuck. Tip: valves come apart without removing the entire assmbly. the coil or plunger can be replaced. The nice thing is water lines feeding the valves don't need to be removed if valve problem is one of the aforementioned parts.
Of course make sure water supply to fridge is shut off!
The water inlet valve is a solenoid-operated switch and when it is energized by electrical power, water is released from the supply line through the water valve and into the compact icemaker mold or the water dispenser.
The water inlet valve is a solenoid-operated switch and when it is energized by electrical power, water is released from the supply line through the water valve and into the compact icemaker mold or the water dispenser.
What this part fixes:
  • Ice maker not making ice
  • Ice maker won’t dispense ice
  • Leaking
Installation Instructions
Robert from Sacramento, CA
The Ice maker just stopped making ice
Kenmore Refrigerator

Turned off the water in the house because no dedicated valve to the refrigerator. Turned on the kitchen sink water to bleed off the water pressure.

Pulled refrigerator from wall and vacuumed up all the dust bunnies and cherrios for a clean work area.

Unplugged refrigerator.
... Read more >Removed 4 screws that held on the rear cardboard panel.

Used 1/2" box end wrench to remove the water supply line form the valve and drained excess water into a bucket. Removed 2 more standard head screws from valve mounting bracket and pulled the valve unit out.

Detached the ice maker and water dispenser feed lines.

Labeled the 2 electric terminals (one purple and one green) and then disconnected them from the valve.

Installed new valve- had to cut a little piece off of water dispenser line from the valve because the new valve mounted without a nut on the end of it. (after market valve initially sent to me was incorrect due to web site error - but later got the correct one)

The after market valve has a different color on the solenoids (like an electric gate that allows water to go through on command). Despite the different color, the electric harness will only match up one way because the terminals are larger on one side.

The installation was fast and easy, however my icemaker is still not working.

I am guessing there is something wrong with the electrical somewhere else but replacing the valve probably fixes this problem most of the time
$128.91
In Stock
Uneven cooling or a refrigerator that is not cooling may point to a refrigerant-flow issue in the sealed system. This OEM step valve regulates refrigerant flow, and its assembly includes a filter drier to help control moisture. Check fit against your refrigerator model. Sealed-system repair requires refrigerant recovery and recharge.
Uneven cooling or a refrigerator that is not cooling may point to a refrigerant-flow issue in the sealed system. This OEM step valve regulates refrigerant flow, and its assembly includes a filter drier to help control moisture. Check fit against your refrigerator model. Sealed-system repair requires refrigerant recovery and recharge.

More Frigidaire Refrigerator Parts

People often need to fix these common parts