My Orders
Frigidaire Refrigerator Hinges
GET YOUR OFFICIAL Frigidaire PARTS TO ENSURE VICTORY
Popular Frigidaire Refrigerator Hinges
This mullion hinge pin is a genuine OEM replacement part, measuring 1.5 inches by 1.25 inches by 0.85 inches. It is specially designed to secure the mullion in refrigerators, allowing it to pivot and ensure smooth door movement. The mullion acts as a barrier between the refrigerator and freezer to maintain the desired temperatures for each section. A damaged or loose hinge pin will result in temperature fluctuations, frost buildup along the door edges, and difficulties opening and closing the door. Therefore, it is important that you replace the pin as soon as it is no longer functioning. Note that your appliance may require two hinge pins, one near the top of the mullion and one near the bottom. Remove the mullion cover, detach the hinge pin, and install a the new one into the hinge assembly. Place the cover back on and verify that the hinge assembly is working by carefully opening and closing the refrigerator doors to check that they are moving smoothly. Each sold individually.
This mullion hinge pin is a genuine OEM replacement part, measuring 1.5 inches by 1.25 inches by 0.85 inches. It is specially designed to secure the mullion in refrigerators, allowing it to pivot and ensure smooth door movement. The mullion acts as a barrier between the refrigerator and freezer to maintain the desired temperatures for each section. A damaged or loose hinge pin will result in temperature fluctuations, frost buildup along the door edges, and difficulties opening and closing the door. Therefore, it is important that you replace the pin as soon as it is no longer functioning. Note that your appliance may require two hinge pins, one near the top of the mullion and one near the bottom. Remove the mullion cover, detach the hinge pin, and install a the new one into the hinge assembly. Place the cover back on and verify that the hinge assembly is working by carefully opening and closing the refrigerator doors to check that they are moving smoothly. Each sold individually.
Installation Instructions
Bernard from NEW WINDSOR, NY
1 Broken plastic mullion hinge. Mullion was not operating correctly.
Removed screw on Mullion so that the replacement hinge can slide onto the small plastic bracket on the door. Slid the mullion on the hinges and screwed in muliion (1 screw).
Designed to support proper door alignment and sealing, this hinge mullion flipper closes the gap between refrigerator doors, helping to maintain optimal cooling performance. It plays a key role in reducing energy loss and keeping food fresh by preventing warm air from entering the fridge. This part fits select models and installs between the doors—please verify compatibility before purchase.
Designed to support proper door alignment and sealing, this hinge mullion flipper closes the gap between refrigerator doors, helping to maintain optimal cooling performance. It plays a key role in reducing energy loss and keeping food fresh by preventing warm air from entering the fridge. This part fits select models and installs between the doors—please verify compatibility before purchase.
This refrigerator door hinge bearing is a durable black plastic component designed to fit into the bottom of the door, providing a smooth pivot point for the hinge pin. It plays a critical role in ensuring effortless door movement, reducing friction, and maintaining proper alignment. Positioned at the lower hinge area, it helps eliminate stiffness, noise, and misalignment that can interfere with door operation. Over time, wear may result in symptoms such as squeaking, clicking, or difficulty opening and closing the door. Replacing this bearing restores smooth functionality and helps prevent issues like door sweating or inefficient sealing.
This refrigerator door hinge bearing is a durable black plastic component designed to fit into the bottom of the door, providing a smooth pivot point for the hinge pin. It plays a critical role in ensuring effortless door movement, reducing friction, and maintaining proper alignment. Positioned at the lower hinge area, it helps eliminate stiffness, noise, and misalignment that can interfere with door operation. Over time, wear may result in symptoms such as squeaking, clicking, or difficulty opening and closing the door. Replacing this bearing restores smooth functionality and helps prevent issues like door sweating or inefficient sealing.
Installation Instructions
Charles from Cypress, TX
Door was making a popping sound when opened and closed
Unscrewd the top hinge cove and removed two bolts from the hinge, lifted door off of the bottom hinge and laid the whole door on the floor using a beach towel to protect it from scratches. Unbolted the bottom hinge plate, replaced it with the new one. Then pulled out the old hinge bearing and replaced with a new one. Installed the door ba
... Read more
ck on the bottom hinge while the magnet on the door strip held it place and rebolted the the upper hinge and reinstalled the hinge cover. All done in less than 10 minutes. No more popping sounds when I open and close the door!
Read less
This is a replacement hinge bearing for your refrigerator. The hinge bearing is found on the door hinge, and reduces friction when the door opens and closes. If the bearing is damaged, you may not be able to open or close the door properly, and in this case, it will need to be replaced. It is made of white plastic and is approximately 2 inches long and 1 inch in diameter. This part is sold individually and is a genuine OEM part.
This is a replacement hinge bearing for your refrigerator. The hinge bearing is found on the door hinge, and reduces friction when the door opens and closes. If the bearing is damaged, you may not be able to open or close the door properly, and in this case, it will need to be replaced. It is made of white plastic and is approximately 2 inches long and 1 inch in diameter. This part is sold individually and is a genuine OEM part.
Installation Instructions
amy from SOMERVILLE, MA
Door sagging, creating a gap to let in condensation
You tube is my best friend for DIY repair. I supported the door with wood blocks, removed the bottom bracket and was able to slide the refrigerator door down and out without removing the freezer door. Replaced both hinge bearings and door stop and washer on bottom hinge and slid the door back into place. Door is very light when empty. Fas
... Read more
t and easy, door opens and closes smoothly and no problem with condensation anymore.
Read less
This part is sold individually.
This part is sold individually.
Installation Instructions
Wesley from PRINCESS ANNE, MD
Door would not open all the way
Removed items from door. Put down blanket on floor. Remove top hinge cover. Removed small bolts. Open and lift door off bottom hinge. Put on blanket on side and remover screw holding upper closure. Installed new closure. Removed bottom closure and installed new closure. Reinstalled door and closed to frame. Reinstalled top hinge and bolts
... Read more
adjusted door and tighten bolts. Reinstalled top hinge cover. For indicator light. Unplug unit and removed screws for kick plate. Removed light holder and removed terminals. Removed light and install in reverse order.
Read less
MAKE THIS REPAIR A GUARANTEED WIN
OVER 2 MILLION PARTS TO ENSURE VICTORY
Sold individually. This cam is located at the bottom of the fridge/freezer door.
Sold individually. This cam is located at the bottom of the fridge/freezer door.
Installation Instructions
Charles from Cypress, TX
Door was making a popping sound when opened and closed
Unscrewd the top hinge cove and removed two bolts from the hinge, lifted door off of the bottom hinge and laid the whole door on the floor using a beach towel to protect it from scratches. Unbolted the bottom hinge plate, replaced it with the new one. Then pulled out the old hinge bearing and replaced with a new one. Installed the door ba
... Read more
ck on the bottom hinge while the magnet on the door strip held it place and rebolted the the upper hinge and reinstalled the hinge cover. All done in less than 10 minutes. No more popping sounds when I open and close the door!
Read less
This door hinge bushing, or hinge bearing, is a genuine OEM replacement part for your refrigerator. The hinge bearing helps the refrigerator door stay on track when opening and closing, ensuring it is flush with the cabinet when closed. You will need a screwdriver and a ratchet in order to complete this repair.
This door hinge bushing, or hinge bearing, is a genuine OEM replacement part for your refrigerator. The hinge bearing helps the refrigerator door stay on track when opening and closing, ensuring it is flush with the cabinet when closed. You will need a screwdriver and a ratchet in order to complete this repair.
Installation Instructions
Edward from Andover, CT
Refrigerator door was not sealing correctly.
Remove screws from lower hinge and carefully remove the door. In my case it was the lower bearing, flip door upside down being careful to remove anything which might fall off first. I removed the door stop and then pulled the broken bearing out with pliers. Then I pushed the new one in and reassembled it.
Sold individually.
Sold individually.
Installation Instructions
Wesley from PRINCESS ANNE, MD
Door would not open all the way
Removed items from door. Put down blanket on floor. Remove top hinge cover. Removed small bolts. Open and lift door off bottom hinge. Put on blanket on side and remover screw holding upper closure. Installed new closure. Removed bottom closure and installed new closure. Reinstalled door and closed to frame. Reinstalled top hinge and bolts
... Read more
adjusted door and tighten bolts. Reinstalled top hinge cover. For indicator light. Unplug unit and removed screws for kick plate. Removed light holder and removed terminals. Removed light and install in reverse order.
Read less
This hinge bearing supports smooth door movement while maintaining proper alignment. Reduced friction helps prevent wear and ensures easy opening and closing. Replacing a worn bearing restores smooth and stable door operation.
This hinge bearing supports smooth door movement while maintaining proper alignment. Reduced friction helps prevent wear and ensures easy opening and closing. Replacing a worn bearing restores smooth and stable door operation.
This door?closing cam helps guide the refrigerator door into a secure shut position, ensuring a tight and consistent seal each time. It reduces strain on hinges by supporting smooth movement, preventing slamming or misalignment. A worn cam can cause popping sounds or difficulty keeping the door closed. Replacing it restores effortless operation and helps maintain the appliance?s energy efficiency.
This door?closing cam helps guide the refrigerator door into a secure shut position, ensuring a tight and consistent seal each time. It reduces strain on hinges by supporting smooth movement, preventing slamming or misalignment. A worn cam can cause popping sounds or difficulty keeping the door closed. Replacing it restores effortless operation and helps maintain the appliance?s energy efficiency.