My Orders
Magic Chef Refrigerator Valves
GET YOUR OFFICIAL Magic Chef PARTS TO ENSURE VICTORY
Popular Magic Chef Refrigerator Valves
This is a dual water inlet valve for your refrigerator/freezer. The water inlet valve is a solenoid-operated switch that, when activated, releases water from the supply line into the water valve. The liquid will then be sent to the compact icemaker mold and to the water line. You will need to replace this part if you are experiencing leaking, or your appliance is not properly dispensing water or ice. This model is blue/green in color and is roughly 3 inches wide, 5 inches long, and 4 inches thick.
This is a dual water inlet valve for your refrigerator/freezer. The water inlet valve is a solenoid-operated switch that, when activated, releases water from the supply line into the water valve. The liquid will then be sent to the compact icemaker mold and to the water line. You will need to replace this part if you are experiencing leaking, or your appliance is not properly dispensing water or ice. This model is blue/green in color and is roughly 3 inches wide, 5 inches long, and 4 inches thick.
Installation Instructions
JIM from Greeley, CO
Refrigerator sat in storage in sub zero weather, water in Dual Water Inlet Valve froze, cracking valve.
This is the 2nd time I have used PartSelect, and this experience was as pleasant as the 1st. The exploded-view diagrams make parts identification very easy; and the photo of the actual part is such a great idea, it allows you to verify what you need. I also got my part (cross country, in 3 days)
Repair Procedure: Shut off water ... Read more supply. It may be easier to work if you disconnect the water supply tube, but it is not required. On the backside of the refrigerator, remove the bottom, black plastic protection panel. You will need a nut driver or battery-powered screw driver with a 3/8" socket tip on it. Next, remove the black metal panel that holds the water inlet valve in place. Remove screws with a nut driver. 1st remove the two flat-pin power connectors. (They are different sizes and color-coded, so there is no room for making a re-hookup mistake). Then proceed to remove the hoses. The hoses are pressure-lock tubing, so push the plastic disk in or down where the tube goes into the main body of the valve. Do this for all three hoses (tubes). Switch water valves and reverse the procedure. **Be certain that the tubes are pushed back in as far as they can go; if you do not re-seat the tubes, the pressure from the water going back in the valve, will blow the tubes right out the valve (ask me how I know this!). Once reassembled, turn the water back on slowly. Make sure you turn the water supply valve all the way open, it seats itself internally when you do and is less prone to drip leaks. That's it! (As a former kitchen remodeler, I find this a great DIY project).
Repair Procedure: Shut off water ... Read more supply. It may be easier to work if you disconnect the water supply tube, but it is not required. On the backside of the refrigerator, remove the bottom, black plastic protection panel. You will need a nut driver or battery-powered screw driver with a 3/8" socket tip on it. Next, remove the black metal panel that holds the water inlet valve in place. Remove screws with a nut driver. 1st remove the two flat-pin power connectors. (They are different sizes and color-coded, so there is no room for making a re-hookup mistake). Then proceed to remove the hoses. The hoses are pressure-lock tubing, so push the plastic disk in or down where the tube goes into the main body of the valve. Do this for all three hoses (tubes). Switch water valves and reverse the procedure. **Be certain that the tubes are pushed back in as far as they can go; if you do not re-seat the tubes, the pressure from the water going back in the valve, will blow the tubes right out the valve (ask me how I know this!). Once reassembled, turn the water back on slowly. Make sure you turn the water supply valve all the way open, it seats itself internally when you do and is less prone to drip leaks. That's it! (As a former kitchen remodeler, I find this a great DIY project).
Read less
This refrigerator water inlet valve is a single-outlet component that controls the flow of water from your home’s supply line to the ice maker and water dispenser. Designed for select refrigerator models, it helps ensure consistent water delivery for ice production and dispensing. If your appliance is leaking, not making ice, or the dispenser isn’t working, a faulty valve may be the cause. Replacing it can restore proper function and prevent water-related issues. Always disconnect power and water supply before installation, and confirm compatibility with your model.
This refrigerator water inlet valve is a single-outlet component that controls the flow of water from your home’s supply line to the ice maker and water dispenser. Designed for select refrigerator models, it helps ensure consistent water delivery for ice production and dispensing. If your appliance is leaking, not making ice, or the dispenser isn’t working, a faulty valve may be the cause. Replacing it can restore proper function and prevent water-related issues. Always disconnect power and water supply before installation, and confirm compatibility with your model.
Installation Instructions
Chad from Gainesville, FL
Water Valve broke and was leaking
1. Unplugged fridge.
2. Unplugged wire harness from valve.
3. Disconnected water supply from valve.
4. Removed valve from fridge chassis
5. Removed plastic tube from valve (supplies ice maker).
6. Removed old fitting from plastic tube and attached to new valve.
7. Attached new valve to fridge (only need 1 scr ... Read more ew)
8. Attached water supply to valve
9. Reattached wiring harness
10. Turned on water supply, checked for leaks
11. Powered on fridge.
12. Enjoy working ice maker.
2. Unplugged wire harness from valve.
3. Disconnected water supply from valve.
4. Removed valve from fridge chassis
5. Removed plastic tube from valve (supplies ice maker).
6. Removed old fitting from plastic tube and attached to new valve.
7. Attached new valve to fridge (only need 1 scr ... Read more ew)
8. Attached water supply to valve
9. Reattached wiring harness
10. Turned on water supply, checked for leaks
11. Powered on fridge.
12. Enjoy working ice maker.
Read less
This valve is located behind the refrigerator. It has a 1/4" compression inlet fitting. This part is a solenoid-operated switch that, when activated, releases water from the supply line to the water valve and into the compact icemaker mold.
This valve is located behind the refrigerator. It has a 1/4" compression inlet fitting. This part is a solenoid-operated switch that, when activated, releases water from the supply line to the water valve and into the compact icemaker mold.
Installation Instructions
Brian from Imperial, CA
Ice Maker had quit due to faulty valve
Repair work was very easy. Water supply was to the icemaker/water dispenser. After removing the outer fiber cover with a screwdriver, the valve was removed by unscrewing one nut. Post removal water lines were removed with a ordinary pair of scissors approximately 1/2" from where it entered the faulty valve. the two electrical connecti
... Read more
ons were then removed from the faulty valve. The water lines were then connected to the replacement water valve very easily by just inserting and applying a small amount of pressure. The electrical connections were then connected, replacement valve reattatched to the frame work (fit perfectly). After this I turned on the water and BINGO ice :) Post knowing the replacement valve worked I re-attached the fiber cover and pushed the refrigerator back in it respective location. Again this repair was very easy and the part arrived sooner than expected.
Read less
This part is a solenoid-operated switch located at the bottom of the refrigerator. When the water inlet valve is turned on, water is released from the supply line through the water valve and into the compact icemaker mold. The kit includes the mounting hardware and bracket plastic tubing fittings. The retaining nut must be cut off the plastic water line and gently pushed into the new valve. To remove, press down on the ring that the tube slides into. Refer to the installation instructions for further guidance. Please note: the manufacturer has redesigned this part and it can appear different than the original. It has a new quick connection.
This part is a solenoid-operated switch located at the bottom of the refrigerator. When the water inlet valve is turned on, water is released from the supply line through the water valve and into the compact icemaker mold. The kit includes the mounting hardware and bracket plastic tubing fittings. The retaining nut must be cut off the plastic water line and gently pushed into the new valve. To remove, press down on the ring that the tube slides into. Refer to the installation instructions for further guidance. Please note: the manufacturer has redesigned this part and it can appear different than the original. It has a new quick connection.
Installation Instructions
Kevin from Boston, MA
no water getting to ice maker
The ice maker had been slowly dying and one day just stopped making ice. No water was getting to the trays.
I read that this could be caused by a failure of the valve, even though the continuity test indicated that the solenoid was okay.
I ordered the part Friday afternoon. It was delivered Saturday. I did the repai ... Read more r in 10 minutes.
I pulled the fridge away from the wall.
I unplugged the fridge. I closed the water supply valve.
I unscrewed the two mounting screws using a flat head screwdriver.
I pulled the old valve out from refrigerator.
Using an adjustable wrench I detached the water supply from the valve. I detached the hose leading to the ice maker from the valve.
I pulled the electrical connectors from the connectors on the valve.
I attached the hoses to the new valve, attached the electrical connector, screwed the new valve in its place, opened the water supply, plugged the fridge back in, checked for leaks, and waited for a few hours.
My ice maker is working better than it has in at least two years.
I read that this could be caused by a failure of the valve, even though the continuity test indicated that the solenoid was okay.
I ordered the part Friday afternoon. It was delivered Saturday. I did the repai ... Read more r in 10 minutes.
I pulled the fridge away from the wall.
I unplugged the fridge. I closed the water supply valve.
I unscrewed the two mounting screws using a flat head screwdriver.
I pulled the old valve out from refrigerator.
Using an adjustable wrench I detached the water supply from the valve. I detached the hose leading to the ice maker from the valve.
I pulled the electrical connectors from the connectors on the valve.
I attached the hoses to the new valve, attached the electrical connector, screwed the new valve in its place, opened the water supply, plugged the fridge back in, checked for leaks, and waited for a few hours.
My ice maker is working better than it has in at least two years.
Read less
MAKE THIS REPAIR A GUARANTEED WIN
OVER 2 MILLION PARTS TO ENSURE VICTORY
This access valve is an authentic manufacturer parts kit used in appliances with a refrigerant such as the refrigerator and air conditioner. This kit includes a valve body, valve core and a valve cap. The body and cap are made of brass while the core is made from steel. If you notice that your appliance is leaking, not cooling adequately and the valve components are corroded, you should replace the access valve. As part of your general maintenance, you should also replace the valve if your appliance is more than 10 years old and the valve has never been changed. Use a valve wrench to remove the valve cap and use a core removal tool to pull out the core. Install the new valve body, core and cap and ensure they are securely fitted. Note that these parts are sold together.
This access valve is an authentic manufacturer parts kit used in appliances with a refrigerant such as the refrigerator and air conditioner. This kit includes a valve body, valve core and a valve cap. The body and cap are made of brass while the core is made from steel. If you notice that your appliance is leaking, not cooling adequately and the valve components are corroded, you should replace the access valve. As part of your general maintenance, you should also replace the valve if your appliance is more than 10 years old and the valve has never been changed. Use a valve wrench to remove the valve cap and use a core removal tool to pull out the core. Install the new valve body, core and cap and ensure they are securely fitted. Note that these parts are sold together.