LG Washer Motors
Popular LG Washer Motors
Your Price
$74.04
In Stock
LG Washer Washing Machine Drain Pump
PartSelect Number PS3579318
Manufacturer Part Number 4681EA2001T
The drain pump and motor assembly may also be known as the washer drain pump and is a part for your washer. The drain pump helps expel water from the washing machine. The drain pump is activated after the spin cycle speed is maintained for a specific period of time. To make this installation you will need a Phillips screwdriver, a small flat-blade screwdriver, a pair of needle-nose pliers, and a pair of slip-joint pliers. Note that the pump casing is not included. This medium-difficulty repair may vary, but can generally be started by disconnecting power, then removing the top of the washer by taking out the four back screws and two small brackets. Then, remove the front panel by taking out the two screws and eight tabs that should be taken from the top. Moving down the front of the washer, remove the door, latch, tub gasket, and drain cover. Disconnect the drain hoses and clip from under the drain assembly, and install new assembly from there. Reassemble parts in direct reverse order -- taking photos during disassembly and keeping parts clearly organized can help here. Despite the number of steps, you will only need a standard Phillips screwdriver to complete this repair.
Fixes these symptoms
- Draining Issues
- Engine runs but does not pump water
- Leaking
- See more...
Installation Instructions
Jorge from Apple Valley, CA
Washing maching wouldn't drain
Removed the top of the washer by removing the 4 back screws and 2 small brackets. Then I removed the front panel, this was actually the hardest part, 2 screws and 8 tabs that you pop out carefully from the top of the panel. I only disconnected the power button and was able to rest the panel on top of the washer. The rest of the washer came apart quickly just moving down the front of the washer and removing the door, latch, tub gasket, drain cover. Removing the pump was just a mater of disconnecting the drain hoses, and one clip under the drain assembly. 3 screws attach the drain to assembly to the pump and only 2 wires that are clearly marked. Reassembly is just going back through in reverse order of disassenbly. The best thing about this is that it all comes apart with a standard phillips screwdriver.
Read more...
Your Price
$183.24
In Stock
LG Washer Rotor Assembly
PartSelect Number PS3522944
Manufacturer Part Number 4413ER1003B
This rotor assembly is a manufacturer-approved replacement part for your washing machine. The rotor is an important part to rotate the tub during the wash cycle. It can need replacing if the magnets or splines become damaged. Unplug the washer before beginning this repair. To complete this repair, you will need a Phillips screwdriver, a 17mm socket wrench, and thread-locking fluid.
Fixes these symptoms
- Spins slowly
- Will not agitate
- See more...
Your Price
$311.16
In Stock
LG Washer Drive Motor
PartSelect Number PS3523290
Manufacturer Part Number 4681EL1008A
This motor works with the belt to drive your dryer's drum.
Installation Instructions
Kevin from MASHPEE, MA
I would turn on the dryer it would run for about 10-20 seconds and then shutoff, and could smell something burning
There’s all sorts of videos on it I watched. It was actually very simple
Read more...
LG Washer Rotor Assembly
PartSelect Number PS3522943
Manufacturer Part Number 4413ER1003A
Installation Instructions
Phillip W. from MILTON, IA
Wouldn't spin
Removed metal cover Removed bolt, removed rotor replaced rotor replaced bolt
Read more...
LG Washer Rotor Assembly
PartSelect Number PS3532774
Manufacturer Part Number AHL72914401
Installation Instructions
Denise from LAKE PLACID, NY
LE code appeared
From my research, I thought I needed to replace the Hall Sensor (also known as the Rotor Positioning Sensor). The Part Select site informed me that I might need to also replace the Rotor Assembly. The site said that I could not order just the Hall Sensor - I needed to order the Washer Motor Stator which would include the Hall Sensor. When I received the order, I found that the Motor Stator did not include the Hall Sensor. I found that I could order a part that matched the Hall Sensor I removed from my machine. I then ordered that part. I installed just the new Hall Sensor - the machine worked. I have returned the unused parts.
Read more...