LG Washer Hinges

Your Price

$6.57

HINGE

★★★★★

11 Reviews

PartSelect Number PS7795475

Manufacturer Part Number MEF62462103

Fixes these symptoms

Lid or door won’t close
See more...

Installation Instructions

John from SAN JOSE, CA

The right side hinge that holds the washer top door broke and needed to be replaced.

Popped out the plastic "doors" that cover the metal actuators. Removed the metal actuators on both right and left sides of the door then unscrewed (3 screws each actuator) them from door frame. Slid the actuators out to enable the door to be removed. Unscrewed 2 screws on the top front of the washer which enabled me to angle the top of the washer to expose the screws that hold the plastic hinges. Unscrewed the hinges (2 screws each) and replaced both of the hinges (I figured I'd do both of them now so I don't have to do it again for another 15 years). Put everything back together and all works like new. Read more...

Videos!

Your Price

$71.65

Hinge

★★★★★

3 Reviews

PartSelect Number PS3523444

Manufacturer Part Number 4774EL2001A

Fixes these symptoms

Door won’t close
See more...

Installation Instructions

Raul from CYPRESS, CA

Dryer door hinge broke.

Followed YouTube video repair process. The only problem is that the door hinge has plastic bushings attached. A couple broke and the parts listing does not show the bushings, nor does the hinge come with them. The door is a bit loose without them. Nonetheless, the repair did the job for now. Read more...

Your Price

$4.45

HINGE

PartSelect Number PS11759966

Manufacturer Part Number 4774FA4016N

Fixes these symptoms

Lid or door won’t close
See more...

Your Price

$14.48

Locking Pin

★★★★★

2 Reviews

PartSelect Number PS3523451

Manufacturer Part Number 4774FR3118B

This is a locking pin, and it works in conjunction with your washer. The part measures to be roughly 3 inches long, and less than an inch wide. The pin is cylindrical, off-white in color, and made entirely of plastic. This part is used to hold the shock absorber on the washing machine. There is a pin used at the bottom and top of the shock absorber. This model is sold individually. If your washing machine is experiencing an above-average amount of shaking and moving this part may be the reason.

Installation Instructions

Todd from STOCKTON, KS

Bearing seal out causing bearings to get wet and very noisy

Watched a short video to figure out to remove panels. After panels were off I removed as much as I could from the inside of the machine. This was not completely necessary however for an extra half hour it made inspection, cleanup and removal of tub housing out the front of the machine much easier. Once out, I split the two halves of the outer basin and sprayed the spider shaft with penetrating oil. Using a brass drift I did have to get a bit aggressive to drive spider shaft out, then I used a heavy metal punch to hammer out the bearings. For those who may not know using brass or a soft metal will keep from damaging reusable parts. At this point it was cleanup time, with dish soap I scrubbed the two halves of the outer basin and the wash basin itself then used emery cloth on the bearing casing and spider shaft. I am a firm believer if u take the time to cleanup properly things go back together much easier. At this point I began to reassemble, replacing tub bearings and seal, the wash basin then putting the two halves of the outer basin back together. I strongly recommend replacing gasket for the halves of the outer basin, for as much as it takes to get there it is money well spent to up the chances of a leak free system. Now with the wash tub back together it was time to reset the tub and hook everything back up. I skipped a lot of steps but if a person pays attention, takes pictures if they have to, even numbers lines with a sharpie it is a very easy repair. Very easy but very time consuming. I am DIY’er, in all I spent about ten hours over two days to do this job. Thus being said I am very particular spent a lot of time cleaning, scrubbing looking at as many wear points and checking for rubbed wires. Hope this helps someone out there, definitely not a strong writer or like doing it. Oh one other thing, I ordered the shocks on the bottom side of wash tub just because I guess not thinking they were bad just thinking I could help tune it up. Was surprised to find the old ones were completely shot, was glad I ordered new ones. After repairs, noise is gone and machine is quiet again. Thank you, your website is very easy to find parts and order. Read more...

Your Price

$6.58

HINGE

★★★★★

2 Reviews

PartSelect Number PS7795474

Manufacturer Part Number MEF62462101

Your Price

$11.31

HINGE

PartSelect Number PS7321743

Manufacturer Part Number 4774EN3002A

This is a locking pin, and it works in conjunction with your washer. The part measures to be roughly 3 inches long, and less than an inch wide. The pin is cylindrical, off-white in color, and made entirely of plastic. This part is used to hold the shock absorber on the washing machine. There is a pin used at the bottom and top of the shock absorber. This model is sold individually. If your washing machine is experiencing an above-average amount of shaking and moving this part may be the reason.

Installation Instructions

Donette from Klamath Falls, OR

Noise and vibration when spinning

Used a video to explain how to do repair. Video showed about 1 1/2 hours, took probably 4 hours at least. Bearings were very difficult to remove and were in very bad shape for a 4 1/2 year old washer. We were very lucky and did not have a spider that needed to be replaced. All and all not to bad of a repair, but without the video we found it would have been a guessing game of how to do the repair. Parts all worked well and the washer is now quiet as a mouse in the spin mode. Spending $200.00 instead of a new washer was the goal and it was completed. Here's hoping to more than 4 additional years before another repair is required. Read more...