EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

LG Washer Sensors

Popular LG Washer Sensors

Damp clothing makes contact with this dryer moisture sensor bar as it tumbles, providing an electrical signal used to monitor drying progress. The metal electrode works with the control system to adjust automatic cycle time as the load becomes drier. A damaged bar or poor electrical contact may cause the cycle to end too soon or leave clothes damp. Replacing a faulty sensor bar helps restore moisture detection, allowing the dryer controls to respond to the load and finish at the selected dryness level. This is an OEM part sourced directly from the manufacturer.
Damp clothing makes contact with this dryer moisture sensor bar as it tumbles, providing an electrical signal used to monitor drying progress. The metal electrode works with the control system to adjust automatic cycle time as the load becomes drier. A damaged bar or poor electrical contact may cause the cycle to end too soon or leave clothes damp. Replacing a faulty sensor bar helps restore moisture detection, allowing the dryer controls to respond to the load and finish at the selected dryness level. This is an OEM part sourced directly from the manufacturer.
What this part fixes:
  • Not Heating
  • Timer Not Working
Installation Instructions
Sheryl from SPRINGFIELD, MO
Dryer not heating
I followed video instruction in disassembling and set screws from each section into diferent small bowls in the order they were removed. Hardest part was some of the screws were really hard to get loose without stripping them and my control panel did not match video but I figured it out. Replacing the parts were easy and putting it back together. While it was apart I cleaned everything including fan blower wheel. Thanks for the right parts and your online video. With your help and a prayer this 62 year old woman fixed the problem and dryer runs like new.
This is a replacement sensor assembly for your washer. It may also be known as a motor rotor position sensor. The sensor assembly monitors the direction and speed of the spinning rotor and communicates this information to the electronic control board. If your washer pumps but will not spin or agitate, you may have a damaged sensor assembly. This part is sold individually, and is an OEM part sourced directly from the manufacturer. Be sure to shut off the power to your washer before you begin this repair.
This is a replacement sensor assembly for your washer. It may also be known as a motor rotor position sensor. The sensor assembly monitors the direction and speed of the spinning rotor and communicates this information to the electronic control board. If your washer pumps but will not spin or agitate, you may have a damaged sensor assembly. This part is sold individually, and is an OEM part sourced directly from the manufacturer. Be sure to shut off the power to your washer before you begin this repair.
What this part fixes:
  • Spinning Issues
  • Spins slowly
  • Will not agitate
Installation Instructions
Mark from Harrisburg, PA
LE Error Message and won't spin drum properly
I first tested the motor per the service manual. I checked the resistance between the terminals of the 3 pin connector. It's supposed to be 5-15 ohms. The motor checked out so I replaced the main electrical board. It turns out that wasn't the problem. After a brief web search I found out that the hall sensor (which is attached to the motor stator) was the likely cause of the failure. I replaced that and everything works great now. And now I have a spare main board in case that ever fails. I also want to mention that I took the time to remove the dispenser box (where the water comes in and is directed to the different cleaning products) and cleaned it with a very strong bleach solution. It got rid of the mildew and funky smell. It seems that the fabric softener caused a lot of mildew to form inside the dispenser directly above the fabric softener tray. The bleach took care of that. This is probably something that should be done routinely to keep the mildew from forming.
LG Washer Sensor Assembly
Part #EBD48922821
$103.35
In Stock
What this part fixes:
  • Spinning Issues
$38.45
In Stock
Accurate temperature feedback helps the appliance control heating throughout a cycle. This thermistor sensor changes electrical resistance as temperature changes, sending a reading to the main control board so it can manage heat as needed. A damaged or inaccurate sensor may cause incorrect temperatures, interrupted cycles, or a temperature sensing fault message. Replacing a faulty thermistor helps restore reliable feedback and normal heating control. The sensor monitors temperature at its installed location, allowing the control system to respond as conditions change during operation. This is an OEM part sourced directly from the manufacturer.
Accurate temperature feedback helps the appliance control heating throughout a cycle. This thermistor sensor changes electrical resistance as temperature changes, sending a reading to the main control board so it can manage heat as needed. A damaged or inaccurate sensor may cause incorrect temperatures, interrupted cycles, or a temperature sensing fault message. Replacing a faulty thermistor helps restore reliable feedback and normal heating control. The sensor monitors temperature at its installed location, allowing the control system to respond as conditions change during operation. This is an OEM part sourced directly from the manufacturer.
What this part fixes:
  • Cycle Not Advancing
  • Will Not Start
Installation Instructions
Luis from LEHIGH ACRES, FL
Te error
Change the thermistor
This motor rotor position sensor is designed for use in washing machines to monitor the direction and speed of the spinning rotor. By communicating this data to the electronic control board, it helps regulate the washer’s performance and ensures efficient operation. For safety, always unplug the appliance before installing the sensor.
This motor rotor position sensor is designed for use in washing machines to monitor the direction and speed of the spinning rotor. By communicating this data to the electronic control board, it helps regulate the washer’s performance and ensures efficient operation. For safety, always unplug the appliance before installing the sensor.
What this part fixes:
  • Spinning Issues
  • Will not agitate
Installation Instructions
John from JUPITER, FL
would drain but did not spin
followed instructions on video , when part was delivered I had washer fixed in about 1/2 hour, very easy to fix . Wife is happy and I saved a lot of money. Thank you partselect.com
Original Equipment Manufacturer

MAKE THIS REPAIR A GUARANTEED WIN

OVER 2 MILLION PARTS TO ENSURE VICTORY

LG Washer Sensor Assembly
Part #6501EL3001A
$159.60
In Stock
This dryer flame sensor detects heat from the igniter and burner flame, helping the gas heating system work properly. Located near the burner, it plays a role in the sequence that lights the gas and produces warm air for drying. A faulty sensor may keep the burner from lighting, leaving clothes damp even though the drum still turns. Replacing a failed sensor helps restore normal heating so warm air can flow through the drum and remove moisture from your laundry. This is an OEM part sourced directly from the manufacturer.
This dryer flame sensor detects heat from the igniter and burner flame, helping the gas heating system work properly. Located near the burner, it plays a role in the sequence that lights the gas and produces warm air for drying. A faulty sensor may keep the burner from lighting, leaving clothes damp even though the drum still turns. Replacing a failed sensor helps restore normal heating so warm air can flow through the drum and remove moisture from your laundry. This is an OEM part sourced directly from the manufacturer.
Installation Instructions
Terry from Goose Creek, SC
Gas Dryer not getting hot
I noticed the flame would start, then quit after about 15 seconds. I checked the flame detector, and found the lenze cracked. I replaced it, and it's as good as gold.

It looked like a hard job to take the drum out to get at the part. But the top was off with 3 screws, the front about 6 I think. Then the front frame, only 4 screws. I think setting the belt tentioner was the hardest thing to do.

Done in 45 minutes, both the job, then the next load of laundry.
$49.50
Special Order
$66.36
In Stock
$66.36
On Order
$44.22
Special Order