My Orders
KitchenAid Cooktop Parts
GET YOUR OFFICIAL KitchenAid PARTS TO ENSURE VICTORY
Popular KitchenAid Cooktop Parts
If your element will not heat, there could be an issue with your drip bowl. This chrome drip bowl is 8 inches in diameter, and fits most electric ranges. Before you replace the drip bowl, make sure the element is turned off and cool to the touch. Installation is easy, just remove the element, replace the current drip bowl, and replace the element. Make sure the small hole on the bowl lines up with the element socket. The manufacturer has substituted this part, it now has a hole in the center, and no longer has a solid bottom. For a step by step guide, click the video below.
If your element will not heat, there could be an issue with your drip bowl. This chrome drip bowl is 8 inches in diameter, and fits most electric ranges. Before you replace the drip bowl, make sure the element is turned off and cool to the touch. Installation is easy, just remove the element, replace the current drip bowl, and replace the element. Make sure the small hole on the bowl lines up with the element socket. The manufacturer has substituted this part, it now has a hole in the center, and no longer has a solid bottom. For a step by step guide, click the video below.
Installation Instructions
Michael from Kings Park, NY
Drip bowls were rusty and rotting through
I simply removed the elements and replaced the drip bowls with new ones. Put the elements back in and my stove looks %1000 better!
This part is located beneath the element and catches any spills.
This part is located beneath the element and catches any spills.
Installation Instructions
Michael from Kings Park, NY
Drip bowls were rusty and rotting through
I simply removed the elements and replaced the drip bowls with new ones. Put the elements back in and my stove looks %1000 better!
This chrome OEM control knob measures 1 1/2" in diameter. It easily attaches onto the D-shaped shaft in order to allow controls to be used. Refer to your model number and user manual to ensure this part is correct for you. This part is sold individually. We recommend replacing all control knobs for your unit at the same time, as they wear at a consistent rate to one another. This very easy repair should only take a few moments to complete; just slide the old knob off the shaft and the new one on.
This chrome OEM control knob measures 1 1/2" in diameter. It easily attaches onto the D-shaped shaft in order to allow controls to be used. Refer to your model number and user manual to ensure this part is correct for you. This part is sold individually. We recommend replacing all control knobs for your unit at the same time, as they wear at a consistent rate to one another. This very easy repair should only take a few moments to complete; just slide the old knob off the shaft and the new one on.
Installation Instructions
Denise from Los Angeles, CA
The knob broke during my housekeepers last kitchen clean up.
Opened the package and put the new knob on my fan for my stove top.
The surface burner plug-in block kit features a newer-style terminal block. This kit is designed for use with ranges and cooktops. This terminal block is how the coil element on your stove connects to the inner wiring of your appliance. Without this connection your burner element would not get the electrical current it needs to heat up. When your element will not heat at all, or if it is not heating properly it is likely an issue with the terminal block. You need to remove the element to replace this part. While you have the element out, inspect the element and the terminal for any corrosion, arcing, or discoloration. If you notice any damage to the element or the terminals we recommend you replace this part as well. This kit includes two metal brackets, two pre-crimped high-temperature wire leads, two ceramic wire nuts, two heat-shrinking insulators, and a mounting screw. Before you begin this repair, make sure you have unplugged your appliance.
The surface burner plug-in block kit features a newer-style terminal block. This kit is designed for use with ranges and cooktops. This terminal block is how the coil element on your stove connects to the inner wiring of your appliance. Without this connection your burner element would not get the electrical current it needs to heat up. When your element will not heat at all, or if it is not heating properly it is likely an issue with the terminal block. You need to remove the element to replace this part. While you have the element out, inspect the element and the terminal for any corrosion, arcing, or discoloration. If you notice any damage to the element or the terminals we recommend you replace this part as well. This kit includes two metal brackets, two pre-crimped high-temperature wire leads, two ceramic wire nuts, two heat-shrinking insulators, and a mounting screw. Before you begin this repair, make sure you have unplugged your appliance.
Installation Instructions
Jon from Oakley, CA
Surface elements quit working
Drilled out old and broken hold down clips, installed new ones(4). Cut old wires attached to surface plug in block, striped wires, and attached new plugin kit(4), warmed up heat shrink with a hair dryer, put in new drip bowels, the stove is like new.
I ordered the parts on line early one morning, the next day they were at my door an ... Read more d installed that day, everything that I ordered was there, and fit properly.
Way to go Part Select.com
Jon
I ordered the parts on line early one morning, the next day they were at my door an ... Read more d installed that day, everything that I ordered was there, and fit properly.
Way to go Part Select.com
Jon
Read less
The surface burner or element on your range provides the heat that you cook with. If your element will not heat, you may need to replace the surface burner. This surface burner is 8 inches in diameter and 2600 watts. The burner element is made of metal and has two prongs that connect it to the range. The manufacturer recommends you replace the burner receptacle at the same time that you replace the surface burner. Many of our customers have rated this repair as very easy. To complete the repair simply lift the old burner up and out, and replace it with the new one. Be sure to disconnect power to the range before beginning this repair.
The surface burner or element on your range provides the heat that you cook with. If your element will not heat, you may need to replace the surface burner. This surface burner is 8 inches in diameter and 2600 watts. The burner element is made of metal and has two prongs that connect it to the range. The manufacturer recommends you replace the burner receptacle at the same time that you replace the surface burner. Many of our customers have rated this repair as very easy. To complete the repair simply lift the old burner up and out, and replace it with the new one. Be sure to disconnect power to the range before beginning this repair.
Installation Instructions
Jonathan from Lilburn, GA
8 inch burner wouldn't come on. Wires shorted out
One screw holds the block onto the stove top. Had to clean out fitting for phillips screwdriver or screw would have stripped because it was old with lots of buildup. Even cleaned out, this screw required great force with phillips screwdriver to keep from stripping. Caution! If you strip it, you'll have to drill it out! The rest was a snap
... Read more
. Cut the old wires leading to the old block (not too close to where wires disappear into back of stove, though!). Strip insulation off both wires and attach with the connectors that came in the kit. Then push the wires into the block, and finally, attach the block back to the stove top (new screw is supplied). Restore power and everything should be fine. One problem: Roper/Whirlpool built their appliance in such a way that when the connector block shorts out, it usually takes the infinite switch with it. So I ended up having to go back and purchase that switch as well (which just so happens to cost twice to three times as much!). If you put it all back together and it still doesn't work, that's probably what happened, so go ahead and remove the knob panel and check that switch (it's right behind the control knobs on the front). You will probably find a burned connector at the back top left or the switch. Don't forget to write down which wire goes where (or just take a picture of it).
Read less
MAKE THIS REPAIR A GUARANTEED WIN
OVER 2 MILLION PARTS TO ENSURE VICTORY
This is a dual surface element for compatible ranges. If the surface heating element for your range is currently not turning on or has issues heating up or maintaining a heat level, it will need to be replaced. This surface heating element features two burners, one smaller involving an inner 1400W element, and one larger burner involving both the inner and outer ones (3000W). Replacing this dual surface element will require a screwdriver or drill, as well as wire cutters and needle-nose pliers. This surface element is sold as an individual OEM part, so you may need to consider how many heating elements you need before ordering.
This is a dual surface element for compatible ranges. If the surface heating element for your range is currently not turning on or has issues heating up or maintaining a heat level, it will need to be replaced. This surface heating element features two burners, one smaller involving an inner 1400W element, and one larger burner involving both the inner and outer ones (3000W). Replacing this dual surface element will require a screwdriver or drill, as well as wire cutters and needle-nose pliers. This surface element is sold as an individual OEM part, so you may need to consider how many heating elements you need before ordering.
Installation Instructions
MELISSA from CHAPLIN, CT
lost two burners
repair was very easy 20 mins and it was done
Also known as grate feet.
Also known as grate feet.
Installation Instructions
Christine from JOHNSTOWN, CO
Too Small
Your website says these are the replacement rubber tips for the grates on the range. They arrive and they are too small and fall out. I spoke to the "chat" on your website. I am informed they do not sell the rubber tips separately. You have to purchase a new set of grates for $294. Ridiculous. Why sells rubber tips for grates that d
... Read more
on't fit the existing grates. I wasted $24 in purchasing the grates which included $9.99 shipping and $5.40 shipping to return the item.
Read less
This stainless burner knob is used in ranges and ovens. The knob allows you to adjust the heat of the surface burner on your range. This knob accepts a D-shaped shaft. If your touchpad does not respond, the knob does not rotate, gets stuck, or the gas igniter glows but does not light, changing out this part can solve your problem. No tools are needed for this easy replacement. Make sure to unplug your range from the power source before installing. Refer to the manual provided by the manufacturer for further guidance.
This stainless burner knob is used in ranges and ovens. The knob allows you to adjust the heat of the surface burner on your range. This knob accepts a D-shaped shaft. If your touchpad does not respond, the knob does not rotate, gets stuck, or the gas igniter glows but does not light, changing out this part can solve your problem. No tools are needed for this easy replacement. Make sure to unplug your range from the power source before installing. Refer to the manual provided by the manufacturer for further guidance.
What this part fixes:
- Gas igniter glows, but will not light
- Touchpad does not respond
- Will Not Start
Installation Instructions
Michael from South Lake Tahoe, CA
BURNER KNOBS MELTED, Burned out electrode
R&R OLD knobs easy .R&R BURNER W/ ELECTRODE, UNSCREW LIFT OFF, UNPLUG SEECTRODE Reverse procedure easy
$28.42
In Stock
The standard y-frame surface burner provides heat to your range. If you notice that your element will not heat, you may need to replace your surface burner. This product is 6 inches in diameter, and 1500W. The manufacturer suggests replacing the receptacle at the same time that you replace the surface burner. Many of our customers have rated this repair as very easy, and you will not need any tools. To complete the repair, simply lift out the old burner and replace it with the new one. Check that the burners are turned off before you begin this repair.
The standard y-frame surface burner provides heat to your range. If you notice that your element will not heat, you may need to replace your surface burner. This product is 6 inches in diameter, and 1500W. The manufacturer suggests replacing the receptacle at the same time that you replace the surface burner. Many of our customers have rated this repair as very easy, and you will not need any tools. To complete the repair, simply lift out the old burner and replace it with the new one. Check that the burners are turned off before you begin this repair.
Installation Instructions
Laurie from Tequesta, FL
Burner element broke and drip bowls needed to be replaced.
I went to the local discount mart and bought drip bowls. The ones available at that store did not fit, so I decided to buy directly from the stove's manufacturer distributor.
The drip pans were simple to replace, as was the new burner element. My old one had broke and was still working, but I decided to replace it when I ordere ... Read more d the drip pans.
Everything was easy to install and it looks like a brand new new stove top! I saved a lot of money doing it myself.
The drip pans were simple to replace, as was the new burner element. My old one had broke and was still working, but I decided to replace it when I ordere ... Read more d the drip pans.
Everything was easy to install and it looks like a brand new new stove top! I saved a lot of money doing it myself.
Read less
Sold individually.
Sold individually.
Installation Instructions
Terry from Rockwall, TX
Surface Element Out
Took 2 screws under front edge of smooth top. Unscrewed ground wire from back of smooth top unit. Unplugged 2 wire bundles, from back. Took bad element out , put in new one. Put back together. About 10 min's tops. Easy peasy.