Kenmore Dryer Hardware

Kenmore Appliance Parts
Shop By Part Type

Popular Kenmore Dryer Hardware

Your Price
$13.44
  In Stock
Roller Support Tri-Ring
★★★★★
★★★★★
(5)
PartSelect Number PS11755850
Manufacturer Part Number WPW10512946
If you notice that your dryer is noisy or will not tumble, you may need to replace the tri ring. This part is triangular, and is less than an inch in size. Tri rings can be found both on the idler pulley shaft, or on the rear drum roller shaft. In either case, you will need to remove the front panel of the dryer and the drum to access the part for repair. Once you have accessed the damaged tri ring, you will simply need to slip it off and replace it with the new one. This part is sold individually. Be sure to disconnect the power source from the dryer before you begin this repair.
Fixes these symptoms
Installation Instructions
John from Tucson, AZ
worn out part
The repair was fairly easy. The most timely part of the repair was removing the twelve screws from the back panel to expose the repair. Read more...
Your Price
$40.60
  In Stock
Igniter Kit
★★★★★
★★★★★
(25)
PartSelect Number PS334180
Manufacturer Part Number 279311
If your dryer will not heat, takes too long to dry, or does not provide enough heat, you might want to replace your igniter kit. This silicone carbide igniter with ceramic holder kit includes the 3-inch flat igniter, bracket, 4-inch wire leads, and the plug. The kit can replace both round and flat igniters and is used for many gas clothes dryers. Be sure to disconnect the power source from your dryer before you do this repair. The igniter is located within the burner assembly, so you will require tools to complete the repair. You will need a putty knife, a small flat blade screwdriver, a 5/16 nut driver, and a 5/16 socket with a ratchet.
Fixes these symptoms
  • No heat or not enough heat
  • Takes too long to dry
  • Will Not Start
  • See more...
Installation Instructions
TEODY from MILPITAS, CA
No Heat. Dryer keeps running but no heat to dry clothes.
Repair was very easy. We are in the internet age so I use it all the time to get info on how to repair any thing in the house including cars. This time it was my dryer. I typed up 'Kitchen Aid dryer has not heat'and pressed searched and PartSelect came up. Typed in the model number and looked up the comments on No Heat. They had pretty cool site that shows videos on how to repair this things too. Came to conlclusion that the THERMAL FUSE was the main problem. Ordered it and as well as the Igniter assy just to make sure and as well as save on the shipping just in case. Ordered on Sunday night and the shipped the next day. It arrived on Tuesday. Unfortunately had a little problem on the shipment. Called PartSelect and they are so awesome they shipped me new parts asap at no extra charge. Awesome Awesome! Parts came in Thursday and first installed the Thermal Fuse and BAAAM! problem solved. Did not need the igniter assembly. Now I have an extra part in storage.
To replace the Thermal fuse.
1. Disconnect Dryer from power outlet. Remove the bolts on the back panel with a 1/4" socket. I used power drill because it is much faster.
2. Locate the Thermal Fuse. Disconnect wires and remove the bolt. Slide it up and pull. Install the new one and reconnect the wires. Replace the panel and plug the dryer.

That solved my problem. It should solve yours too. The whole process was less than five minutes.
Read more...
Your Price
$12.34
  In Stock
Screw
★★★★★
★★★★★
(3)
PartSelect Number PS11757021
Manufacturer Part Number WPW10661886
This mounting screw is a genuine OEM replacement part for the door handle in your refrigerator. If you are having trouble shutting the refrigerator door, or opening it, replacing this screw can help solve the issue. Replacing this part is easy and requires minimal disassembly of the refrigerator end cap handle. Your will need a screwdriver to complete this repair.
Installation Instructions
Mike from WILMINGTON, NC
stud screws for handles
easy Read more...
Your Price
$7.76
  In Stock
Cover Screw
PartSelect Number PS11740701
Manufacturer Part Number WP308685
Sold individually.
Installation Instructions
Peter from WRENTHAM, MA
Kenmore 80 Series Washer - Agitator Stopped Working
First I screamed at the ceiling, because I have a three year old and an infant, and the washing machine was dead. Then I went to youtube. It seemed like the "agitator dogs" were the issue.

In this spirit of any repair, I replaced them, and it was not the issue. I don't know what I expected.

Ceiling. YouTube. Pacing.

Then I figured it was this part - the motor coupling. I unplugged the machine and took out the drain tube. I leaned the machine back and propped it up with an empty detergent bottle, because those were abundant. Ratchet off a few bolts and the motor comes out. The coupling was indeed broken. The new one slips right in - I tapped it a few times with a mallet for good measure / vengeance. Ratcheted the bolts back on and tipped it back up.

Pros: Washer works now.
Cons: Everest-esque laundry pile to address.

But hey, it worked! I am no handyman and it wasn't too bad at all. Half hour tops.
Read more...
Your Price
$14.17
  In Stock
Screw
PartSelect Number PS417463
Manufacturer Part Number 131302800
This is a replacement screw for your washer or dryer. The screw is approximately half an inch in length and is a Phillips-head screw. It screws in from the outside of the drum, into the vane/baffle. The main reason you would replace this screw is if the old screw is missing or damaged. This part is sold individually and is an OEM part sourced directly from the manufacturer.
Installation Instructions
Edward from Baltimore, MD
Drying too slowly
Removed access plate from back bottom left
Removed belt from motor
Needed to lift up top of dryer
Inserted flathead screwdirver in front under top to push in two metal clips holding top down
Lifted up top of dryer
Removed 2 screws holding on front of dryer
Removed front of dryer
Broke Door Switch removing front of dryer. I should have depressed the metal sides in and pulled switch through hole.
Instead, I tried to remove the leads. This broke the fragile prongs.
Started dryer (with belt removed so drum doesn't spin)
Verified ignightor came on every heating cycle
Gas turned on properly
Gas turned off after 90 seconds
Gas never came back on
Indicitive of bad coils
New coils solved the problem
Replaced door switch and lint trap cover in the process.
Read more...
Your Price
$7.76
  In Stock
Screw - 10-16 x 1
★★★★★
★★★★★
(2)
PartSelect Number PS11741409
Manufacturer Part Number WP3387230
This screw is sold individually.
Installation Instructions
Wendy from BRAINTREE, MA
Freezer handle came loose on one side
Discovered that the seating in the handle was stripped on one side so removed the old handle (toughest part of the repair). Based on a previously asked/answered question, the PartSelect website provided an accurate list of the required parts (and corresponding part numbers) so I had everything I needed. Installing the new handle was very straightforward and quick. Read more...
Your Price
$15.69
  In Stock
Single Front Panel Cip
★★★★★
★★★★★
(2)
PartSelect Number PS11731288
Manufacturer Part Number W10854425
This part is the replacement single front panel clip for your dryer. It is made of metal and is approximately 2 inches long and ¾ inch wide. The front panel retainer clip is what holds the front panel on to the dryer. If the clip is damaged or missing, or if the front panel appears loose, you may need to replace the clip. This part is sold individually and is an authentic OEM part.
Fixes these symptoms
Installation Instructions
Sean from BAR NUNN, WY
Belt was slipping, and having a hard time spinning the drum
First off, start by turning of the breaker to the dryer and confirming the power has been turned off. Next, remove the lint screen and two screws holding the lint screen housing to the lid. Remove the two side moldings on the control panel and the two screws holding doun the enclosure. Slide the control enclosure forward and lift up . Take a picture of the wiring for later reference and carefully unplug the wires and set the enclosure aside. Next, remove the two screws holding the rear lid retaining clips. Gently pry up on the front of the lid to realese hold doun clips, swing the lid up and remove it from the rear clips, set the lid aside. Remove the two screws on corners of front cover located near the top, unplug the door switch. Remove the front cover by lifting straight up, set aside. Now remove the belt from the motor by realeasing the tensioner and remove it from the drum. You can now remove the drum through the front. Now is a good time to check the condition of your drum rollers, clean them as needed or replace them. Clean the roller shafts and apply a quality grease. "Clean the roller groove on the drum" this is what makes the drum sound bumpy! Remove the rear seal and replace it as per the instructions that come with the seal. The glue dries quickly, so have the seal fully in place and apply glue to small areas replacing the seal fully before moving on. You can now reinstall the drum being careful not to damage the seal. Place the drum on the rollers, reach inside and work the seal into place. You can now replace the belt and work in reverse with the casings! It took me longer to type these instructions than it did to make this repair! Enjoy your like new machine! Read more...
Your Price
$7.76
  In Stock
Thrust Washer
★★★★★
★★★★★
(2)
PartSelect Number PS11740482
Manufacturer Part Number WP233520
This genuine OEM washer has a 3/4 inch outside diameter. This thrust washer can be used on most makes and models of dryers. A complete list of compatible dryers is available below. The washer is found on dryers around the drum support rollers and idler pulleys, and helps prevent the rollers and pulleys from bumping up against the brackets they are installed on. Your thrust washer could be defective if you notice your dryer wont tumble, rotate, or turn; or there is a load squealing or whining noise when the dryer tumbles. The repair is a relatively easy job. You will require a putty knife, 5/16 inch nut driver, and E-Ring pliers. Remember to disconnect the power to your dryer before you begin the repair.
Fixes these symptoms
  • Burning smell
  • Noisy
  • Pumps but will not spin
  • See more...
Installation Instructions
Chris from Hopedale, MA
Drum not centered , clothes getting stuck in dryer
The first thing I did was to unplug the dryer from the wall. Then I removed the bottom two screws and slid the bottom cover off so i could see all the way to the back, I tipped the dryer back against the wall and searched for the problem with a flashlight. I noticed that one of the guide wheels that held the drum in place was sheared off. I took the new drum support roller out and carefully slid it over the shaft, I had to jiggle it around for a bit, but then it finally was seated correctly. I replaced the washer and then the clip using a pair of needle nose pliers and a regular screw driver and then turned the dryer by hand to see if the wheel came off. After confirming that it worked, I put the cover back on, and plugged it in and tested it. Read more...
Your Price
$7.76
  In Stock
Screw, 8/18 x 3/8
★★★★★
★★★★★
(2)
PartSelect Number PS11746840
Manufacturer Part Number WP90767
This screw is sold individually.
Installation Instructions
Alexander from Lakeland, FL
Broken Dryer Knob
First let me just say that Partselect.com is now one my stored favorites in my web browser. I came home from a business trip and saw a pair of pliers on the dryer. I thought that was odd until my wife informed me that the knob on the dryer had broken. So she was using the pliers to select the cycle. Somehow she knew where the missing pointer was actually pointing. Since the dryer was over 5 years old I saw this as an opportunity to upgrade both appliances. Not with my frugal wife. A search of the Internet popped up partselect. I ordered Wednesday morning and the parts where on my doorstep late Thursday. Trust me I was very surprised. Everything worked perfectly. Two thumbs up!!! Read more...
Your Price
$14.69
  In Stock
SCREW
PartSelect Number PS417085
Manufacturer Part Number 131168200
Sold individually.
Installation Instructions
Glenn from Fort Worth, TX
Dryer squealed loudly
First, I removed the top panel which is held on at the front by pressure clips. Second, I removed the entire front panel which entailed removing 2 screws and 2 wire couplings. Third, I removed the 3 screws on the inside center of the drum which turned out to be unnecessary. Fourth, I slid the drum forward in order to access the rear bearing. Lastly, I replaced the entire bearing assembly including the shaft, bracket, bearing, grounding ball and clip. Again, probably not needed but I had ordered the parts in advance in preparation for the worst. Read more...

Related Parts