Kenmore Dryer Caps and Lids

Your Price

$20.61

Kenmore Dryer Guide Cover

★★★★★

13 Reviews

PartSelect Number PS12368455

Manufacturer Part Number 3550EL1005C

This is an OEM lint filter guide cover made for LG dryers. This is one of three pieces in the entire lint filter assembly, along with the lint filter guide and filter itself, which are both sold separately from this. This guide cover is made entirely of plastic and measures approximately 16 inches wide. If the lint filter assembly for your dryer is broken, chipped, or cracked, and ultimately cannot perform efficiently anymore, covers like this must be replaced immediately. This cover comes individually and without any accompanying parts, so be sure to check your lint filter assembly for the necessary parts before ordering.

Your Price

$40.77

Kenmore Dryer Lint Filter Guide Cover

★★★★★

21 Reviews

PartSelect Number PS3519694

Manufacturer Part Number 3550EL1006B

Located just inside the dryer door. The guide cover (or grill cover) is where the hot air circulates through the appliance. This part may crack or become damaged over time, causing clothes to get caught on it while it is in motion. Open the dryer door, remove the lint screen, and remove the screen using your screwdriver. Line up the new grill cover with the moisture sensor and the housing on either side, and it should snap into place. Once it is firmly in place, use your screwdriver to put the screws back in.

Fixes these symptoms

Marks left on clothes
See more...

Installation Instructions

mary f from BERMUDA DUNES, CA

screen and filter need to be replaced

remove filter , unscrew old screen , clean old area and screw back screen and replace filter Read more...

Your Price

$78.41

Kenmore Dryer Cover

★★★★★

3 Reviews

PartSelect Number PS8746645

Manufacturer Part Number 137554110

Discover the ultimate solution to maintaining your dryer's efficiency with this genuine OEM lint housing cover. Primarily designed for use with select Frigidaire models, this high-quality item ensures that clothing is prevented from slipping into the lint duct. Remember, while parts may appear similar in size and shape, small variations can occur, thus it's essential to verify that the component is appropriate for your model before purchase. To install this lint screen grille, ensure to unplug the dryer and don protective work gloves for your safety. Maintain the efficiency and longevity of your beloved Frigidaire appliance with this top-tier lint housing cover.

Your Price

$38.88

Kenmore Dryer Filter Cover

PartSelect Number PS3648317

Manufacturer Part Number MCK66787901

This part is the replacement lint filter cover for your dryer. It is made of gray plastic and is approximately 11-1/2 inches by 1-1/4 inches. The lint filter cover fits on top of the lint filter and protects it. The main reason you would want to replace the lint filter cover is if it is cracked or broken. This part is sold individually and is an authentic OEM part sourced directly from the manufacturer.

Fixes these symptoms

Marks left on clothes
See more...

Your Price

$13.91

Kenmore Dryer Refrigerator Plug Door Rvsbl

★★★★★

2 Reviews

PartSelect Number PS11701216

Manufacturer Part Number WR01X21159

Sold individually.

Installation Instructions

roger from rio rancho, NM

glides and top housing worn out

removed top of unit, control panel and front of dryer. Disassembled assembly and installed new housing and glides, reassembled and checked operation Read more...

Your Price

$63.04

Kenmore Dryer Guide Cover

PartSelect Number PS3519695

Manufacturer Part Number 3550EL1006D

Your Price

$70.04

Kenmore Dryer Lint Trap Cover

★★★★★

2 Reviews

PartSelect Number PS418307

Manufacturer Part Number 131622202

Screws sold separately.

Installation Instructions

Edward from Baltimore, MD

Drying too slowly

Removed access plate from back bottom left
Removed belt from motor
Needed to lift up top of dryer
Inserted flathead screwdirver in front under top to push in two metal clips holding top down
Lifted up top of dryer
Removed 2 screws holding on front of dryer
Removed front of dryer
Broke Door Switch removing front of dryer. I should have depressed the metal sides in and pulled switch through hole.
Instead, I tried to remove the leads. This broke the fragile prongs.
Started dryer (with belt removed so drum doesn't spin)
Verified ignightor came on every heating cycle
Gas turned on properly
Gas turned off after 90 seconds
Gas never came back on
Indicitive of bad coils
New coils solved the problem
Replaced door switch and lint trap cover in the process. Read more...