Hotpoint Dishwasher Parts

Hotpoint Appliance Parts
Shop By Appliance Type Shop By Part Type

Popular Hotpoint Dishwasher Parts

Your Price 1.29
  In Stock
RACK SLIDE END CAP
★★★★★
★★★★★
(47)
PartSelect Number PS2370502
Manufacturer Part Number WD12X10304
The rack slide end cap is the part that attaches to the rails of your upper dish rack and prevents the dishrack from sliding too far out. If you find the dish rack is causing the door to not close properly, it may be due to the part being worn out or damaged. All you need to complete this repair is a small flat blade screw driver. Simply pop out the cap and snap the new one into place. If the rear cap needs to be replaced you will need to remove both front caps and slide the rack completely off for full access.
Fixes these symptoms
  • Door latch failure
  • Door won’t close
  • Not cleaning dishes properly
  • See more...
Installation Instructions
Joseph from Haymarket, VA
Worn/broken plastic parts were causing misery
Order arrived two days after being placed. Super easy to remove the old, worn, broken plastic parts and replace with new. Everything popped right on just as shown in the diagram. Our happiness with our dishwasher has increased 100%. BTW, thanks to the very helpful, friendly and knowledgeable staff at PartSelect.com -- next job, replace the ice maker in the freezer! Read more...
Your Price 27.76
  In Stock
Lower Rack Wheel Kit - 8 Pack
★★★★★
★★★★★
(97)
PartSelect Number PS11726733
Manufacturer Part Number WD35X21038
This lower rack wheel kit includes 8 wheels and 8 axles that allow the lower dishwasher rack to slide in and out smoothly. If your dishwasher door will not close, is noisy when operating, or the dishes are not cleaning properly, you might need to replace one or more of the wheels. Each wheel and axle are made of plastic, and fit into one another so they can be clipped on to the lower dishwasher rack. Many of our customers found this repair to be quick and easy, and the only tool you should need to complete the repair is a pair of pliers.
Fixes these symptoms
Installation Instructions
Mark from Huntingdon Valley, PA
Lower rack wheel was melted
Unsnapped clip,and moved it 90 degrees. Slip wheel and clip off. Installed clip on new wheel. replaced new wheel. The wheel did not come with a new clip and was not suggested on the parts list. The existing clip was still OK but if it was not, I would have had to order a clip and wait. All in all, a good experience. Read more...
Your Price 18.18
  In Stock
Upper Roller and Axle - Kit of 4
★★★★★
★★★★★
(55)
PartSelect Number PS3486910
Manufacturer Part Number WD12X10327
The dishwasher roller assembly attaches to the upper dishrack. It allows the dishrack to slide out easily. If the upper rack keeps falling off the track in dishwasher, the door will not close, the door makes noises, and/or dishes are not cleaning properly, it is best to replace it for more security. A flat-blade screwdriver is the only tool needed for this installation. Slide open the upper dishwasher rack and remove the retaining tabs from both ends of the rack and slide it out. Locate the older roll assembly, remove it, and replace the rollers. Remember to put back the tabs on each side before sliding it back in. Make sure the dishwasher is turned off before starting this repair.
Fixes these symptoms
  • Door latch failure
  • Door won’t close
  • Noisy
  • See more...
Installation Instructions
Carl from Fairfield, TX
The rollers on the upper rack broke
There are eight guides that hold the rack rails in place. Use a Phillips screwdriver to remove the top two guides on each side in order to remove the rack from the dishwasher. The plastic axles on the rack and the rollers snap on. Use the hammer and punch to bend the metal clip on one end of the rail. Remove the plastic end piece then slide the rollers out. Place two new rollers in the rail and put the plastic end piece on. Use the hammer and punch to bend the metal clip back into place. Snap the rails on the rack and set the rack on the guides in the dishwasher. Replace the top guide using the screwdriver, you will have to twist the rails in order get them in between the
guides.
Read more...
Your Price 12.57
  In Stock
Corner Tub Baffle - Lower Left
★★★★★
★★★★★
(15)
PartSelect Number PS263964
Manufacturer Part Number WD8X228
The corner tub baffle may also be known as the door baffle and is a part used on your dishwasher. The left and right side baffle on your dishwasher should be installed and replaced at the same time. This specific part is for the lower left side of your appliance, the right-side is sold separately. The function of the tub corner baffle is to prevent water from leaking through your dishwasher door. The function of this specific one is to stop water from leaking through the bottom left hand side of your dishwasher door. You will not need any tools to make this installation.
Fixes these symptoms
  • Leaking
  • Not cleaning dishes properly
  • Not draining
  • See more...
Installation Instructions
Kenneth from Goleta, CA
Dishwasher leaking at door seal.
Removed door seal and corner baffles by hand (no tools required). Replaced same parts with minor tweaking to get proper alignment of new seal. Strongly recommended: remove dishwasher trays in order to get head and shoulders inside for proper view of seal placement. Read more...
Your Price 12.03
  In Stock
Corner Tub Baffle - Lower Right
★★★★★
★★★★★
(12)
PartSelect Number PS263963
Manufacturer Part Number WD8X227
This baffle fits the lower right hand corner of some dishwashers. It is black rubber and has a matching left hand lower corner baffle. It is recommended that you replace and install both left and right at the same time. It will become evident that this part needs to be replaced if you are experiencing leaking or lack of draining. This is a very easy repair that requires no tools. Open the dishwasher door and simply use your hands to remove the baffle found in the lower right hand side of the dishwasher. Clean out any dirt and insert your new one into place.
Fixes these symptoms
  • Leaking
  • Not cleaning dishes properly
  • Not draining
  • See more...
Installation Instructions
Kenneth from Goleta, CA
Dishwasher leaking at door seal.
Removed door seal and corner baffles by hand (no tools required). Replaced same parts with minor tweaking to get proper alignment of new seal. Strongly recommended: remove dishwasher trays in order to get head and shoulders inside for proper view of seal placement. Read more...
Your Price 17.93
  In Stock
Silverware Basket
★★★★★
★★★★★
(17)
PartSelect Number PS261346
Manufacturer Part Number WD28X265
The silverware basket, used for dishwashers, is in the bottom of the dishrack. The basket is used to hold eating utensils such as spoons, forks, and knives. If the basket is worn out or broken, you should replace it with this part. No tools are required as it is an easy replacement. If you need further guidance refer to the instructions provided by the manufacturer. For safety precautions make sure to unplug the dishwasher and wear gloves.
Fixes these symptoms
Installation Instructions
Joseph from Elmendorf, TX
Basket was lost
Opened package from Parts Select.
Removed Silverware basket from package.
Opened Dishwasher.
Inserted Silverware Basket in rack.
Closed Dishwasher.
Discarded shipping package.
Told wife I fixed Dishwasher.
Sat down & had a beer.
Read more...
Your Price 152.08
  In Stock
Dishwasher Lower Dish rack with Wheels
★★★★★
★★★★★
(53)
PartSelect Number PS3486947
Manufacturer Part Number WD28X10284
Fixes these symptoms
Installation Instructions
michael from Bloomington, IN
lower dishrack rusted
replaced rack, no repairs required Read more...
Your Price 22.10
  In Stock
Drain Valve Shaft Seal
★★★★★
★★★★★
(10)
PartSelect Number PS263930
Manufacturer Part Number WD8X181
The drain valve shaft seal is a part for your dishwasher drain pump valve. This seal creates a watertight closure around the flapper valve shaft. This part can be accessed through the access panel at the front for a built-in. For a portable dishwasher, consider disconnecting and unplugging the taps and lay on a blanket to access the bottom of the machine. This will need to be replaced if you notice leaking coming from the pump. This part measures approximately 3/8 inches in diameter and is black in color. This is a genuine OEM part that comes right from the manufacturer.
Fixes these symptoms
Installation Instructions
Joseph from Livermore, CA
Water leak from gate (diverter) valve shaft
This was a fairly simple repair. After disconnecting power to the dishwasher and removing the panel below the door, first had to remove a retainer C clip from the gate valve shaft. Then disconnected the linkage from the gate valve solenoid, removed two return springs and slid the gate valve contol arm off the shaft. Then removed the solenoid bracket that was fastened to the housing by 2 screws. This allowed access to the push on nut on the valve shaft. Removed the old push on nut which exposed the leaking seal. Removed the bad seal, then moistened and carefully slid on and seated the new drain valve shaft seal. Affixed new push on nut. Reinstalled the above mentioned parts that were removed. Problem solved - no more leak. Total cost $18.81 for factory GE parts plus $6.95 shipping. Thank you PartSelect. Read more...
Your Price 13.78
  In Stock
Interlock Switch
★★★★★
★★★★★
(14)
PartSelect Number PS1481922
Manufacturer Part Number WD21X10261
The interlock switch may also be referred to as a belt switch. This part is a simple on/off mechanism that prohibits the appliance from operating when the door is open. This is a part for your dryer. The interlock switch senses the door is shut and the dryer can begin. This part might need to be replaced if your dryer is not starting or is in process while the door is open. The black rectangular part of the switch is approximately 2 inches long and a 1/2-inch wide with two gold plates on either end. This is a genuine OEM part that is sourced right from the manufacturer.
Fixes these symptoms
  • Door latch failure
  • Shuts off too soon
  • Will Not Start
  • See more...
Installation Instructions
Steven from EPHRATA, WA
interlock switch was bad. Prevents the dishwasher form running as it "thinks" the door is still open.
Opened door, removed screw holding down metal plate that presses against interlock switch when door is closed. Removed plastic cover thingy that is over interlock switches. Removed the interlock switch by pressing the plastic lock thingy away from switch. Pulled the wires off each end of the interlock switch. Removed new interlock switch from plastic bag and reversed above procedure. Done, shut door and the dishwasher works. Read more...
Your Price 5.83
  In Stock
Upper Track Roller Kit
★★★★★
★★★★★
(2)
PartSelect Number PS259157
Manufacturer Part Number WD12X332
The track roller on your dishwasher allows the tracks that hold the upper dish rack to slide in and out effectively. If you notice that your upper dish rack is struggling to slide in and out, you may need to purchase a new track roller kit to replace the damaged one. This kit comes with the roller, one screw, and a washer for easy assembly. The roller is approximately 1-1/4 inches in diameter and the screw is approximately 1-1/2 inches in length. To complete this repair, you will need to remove the upper dish rack, as well as the rail.
Installation Instructions
Dave from Littleton, CO
Parts were old and worn out
The repair was easy. A couple turns of a screwdriver was all that was necessary to remove the rollers and slide assembly. The I simple installed the new rollers. Slid the slide into place between the rollers and then added the back caps to the slide. Replaced the rack rollers on the top basket and then slid it into position between the new slides. Once in place, I attached the end caps to the front of the slide. Simple and quick. Read more...

Appliance Type

Related Parts

Popular Hotpoint Dishwasher Models

Below are the most popular Hotpoint Dishwasher models we have. Enter your model number in the search box to find your model.