Hotpoint Dishwasher Hinges

Videos!

Your Price

$16.05

Hotpoint Dishwasher Hinge Arm Link

★★★★★

9 Reviews

PartSelect Number PS259336

Manufacturer Part Number WD14X10009

The hinge link on your dishwasher connects the spring to the dishwasher door hinge. If the hinge link becomes cracked or damaged, you may not be able to shut or lock your dishwasher door properly. In this case, you will need to replace the hinge link. Pull out your dishwasher to inspect the hinge and spring, if the link is broken, it may be disconnected and on the ground already. If not, you can remove the hinge arm link by simply disconnecting it from the hinge and spring, then replacing it with the new part. The hinge arm link is a small piece of white plastic about an inch and a half long. It is sold individually, and is an OEM part from the manufacturer.

Fixes these symptoms

Door latch failure
Door won’t close
See more...

Installation Instructions

Margaret from Meridian, MS

plastic hinge arm link broke causing door to flop open

First I had to unscrew screws under the counter then pulled built in dishwasher out from under the counter, attached hing arm link to right side bracket on door, and the other end I attatched to a spring at the back of the unit. Thats it! and pushed the dishwasher back into place. All back to normal....by the way Im a 67 yr old great grandmother... Read more...

Your Price

$16.04

Hotpoint Dishwasher Door Cable

★★★★★

7 Reviews

PartSelect Number PS7320283

Manufacturer Part Number WD01X10569

This part is the replacement door hinge cable for your dishwasher. The door hinge cable connects the door spring to the door hinge, and allows the door to drop down slowly when it is opened. If you open your dishwasher and the door drops down quickly, your door hinge cable may need to be replaced. Be sure to disconnect the water and power sources from the dishwasher before you begin this repair. The door hinge cable is sold individually.

Fixes these symptoms

Door latch failure
Door won’t close
See more...

Installation Instructions

Avery from SEDALIA, CO

Cable had come off of roller

First went to U Tube to view installation instructions and location of part. It was fairly easy to replace since I had installed the unit. I was able to move the unit out enough without disconnecting any line since there was enough slack in all three connections, only shut the power off. I did use the new parts even though the older ones were not broken. The nylon pulley wheel had built up with lint causing the cable to come off. Read more...

Your Price

$16.05

Hotpoint Dishwasher Pulley Hinge

PartSelect Number PS11700873

Manufacturer Part Number WD16X21836

Your Price

$27.36

Hotpoint Dishwasher Door Cable And Eyelet

★★★★★

15 Reviews

PartSelect Number PS263918

Manufacturer Part Number WD7X14

This part is sold individually. It is recommended that both sides are changed when replacing one.

Fixes these symptoms

Door latch failure
Door won’t close
See more...

Installation Instructions

Karthik from Springfield, VA

Dishwasher door became really heavy to operate

Note: This procedure assumes replacement of both eyelet cables. It is recommended that both eyelet cables be replaced at the same time.

1. Using a Philips' head screwdriver, remove the four screws holding the lower front panel (below dishwasher door).
2. Remove the faulty eyelet cable(s) hooked into the springs at one end and the door hinges at the other.
3. Take the new eyelet cables and hook them onto the door hinge on either side. Ensure a secure fit.
4. Guide the eyelet cable around the spinwheel on one side and insert the hooks of the springs into the eyelets.
5. Pull on the springs and insert their hooks into the eyelets of the other cable, ensuring a secure fit.
6. Test the door by opening and closing it a few times to ensure the spring has tension.
7. Replace the lower front panel cover removed in step 1 with its screws. Read more...