Hotpoint Dishwasher Hardware

Hotpoint Appliance Parts
Shop By Part Type

Popular Hotpoint Dishwasher Hardware

Your Price
$6.24
  In Stock
Push On Nut
★★★★★
★★★★★
(5)
PartSelect Number PS298353
Manufacturer Part Number WR2X7054
This push on nut is for your dishwasher or refrigerator. As the name suggests, it pushes into place, rather than being screwed in. It is approximately half an inch in diameter and is made of stainless steel.
Installation Instructions
Joseph from Livermore, CA
Water leak from gate (diverter) valve shaft
This was a fairly simple repair. After disconnecting power to the dishwasher and removing the panel below the door, first had to remove a retainer C clip from the gate valve shaft. Then disconnected the linkage from the gate valve solenoid, removed two return springs and slid the gate valve contol arm off the shaft. Then removed the solenoid bracket that was fastened to the housing by 2 screws. This allowed access to the push on nut on the valve shaft. Removed the old push on nut which exposed the leaking seal. Removed the bad seal, then moistened and carefully slid on and seated the new drain valve shaft seal. Affixed new push on nut. Reinstalled the above mentioned parts that were removed. Problem solved - no more leak. Total cost $18.81 for factory GE parts plus $6.95 shipping. Thank you PartSelect. Read more...
Your Price
$6.24
  In Stock
Screw 8-16 hxw 1/2 Stainless Steel
★★★★★
★★★★★
(2)
PartSelect Number PS258461
Manufacturer Part Number WD02X10067
Sold Individually.
Fixes these symptoms
Installation Instructions
Farhan from EL DORADO HLS, CA
Spray arm fell off and melted due to screw loss
1. Unscrew the nozzle part from the dish rack and pull it down from the clip side. 2. Replace the new nozzle by inserting the plain side in first and clip it in. 3. Tighten the screw. 4. Insert the spray arm hole in the nozzle and tighten the screw with washer. 5. Start washing dishes Read more...
Your Price
$6.24
  In Stock
SCR 8-18 AB TR 7/8S
PartSelect Number PS958858
Manufacturer Part Number WD02X10106
Installation Instructions
Lawrence from Smithtown, NY
Tray rollers had broken off.
Replaced the original roller connectors with newly designed connectors. Works much better. Read more...
Your Price
$6.24
  In Stock
Screw - 8-18 B HXW .480 S
PartSelect Number PS2337849
Manufacturer Part Number WD02X10160
This is a genuine hex head screw replacement, designed for use with dishwashers. Most of this type of screw is used to hold the kickplate in place on the bottom of your appliance. This screw is sold individually, therefore you'll need to order the quantity you require. It measures 8-18 x .480.
Your Price
$42.26
  In Stock
Lower Spray Arm and Support Assembly
★★★★★
★★★★★
(4)
PartSelect Number PS260529
Manufacturer Part Number WD22X10008
This part comes with the telescopic tower.
Fixes these symptoms
Installation Instructions
sheila from dyersburg, TN
spray arm was cracked and the top part kept spraying off
just unscrewed it from the dishwasher with my hand and put the new one back on the same way Read more...
Your Price
$6.24
  In Stock
Screw
★★★★★
★★★★★
(1)
PartSelect Number PS283515
Manufacturer Part Number WR01X10065
Size: 10-32 GXTT FLP .595 Sold individually.
Your Price
$9.70
  In Stock
Shoulder Screw
★★★★★
★★★★★
(2)
PartSelect Number PS1483099
Manufacturer Part Number WR01X10623
This is a self-tapping sheet metal screw and is used in conjunction with multiple appliances in your household. This part is size eight and has 18 threads to the inch. The AB in the name indicates that it is a self-tapping screw with sharp points and fine threads. This part has a hexagonal head with built in washer, but is often referred to as simply a hex head. This screw is 9/16 inches in length. This piece is sold individually.
Your Price
$12.09
  In Stock
Hose Clamp Kit
★★★★★
★★★★★
(2)
PartSelect Number PS270806
Manufacturer Part Number WH1X2036
This is a water hose clamp kit for a variety of appliances including dishwashers and washers. This is a genuine replacement part. The kit includes two hose clamps. The smaller of the two is 1 inch in diameter while the larger one is 2 inches in diameter. The hose clamps secure the end of the water hose in place to prevent the hose from leaking. If you notice leaking from the hose of your appliance, you may need to replace this kit. Protect your hands with work gloves during this repair to avoid injury.
Fixes these symptoms
Installation Instructions
Richard from Garden City, NY
washer had heavy wet clothes left after spin cycle
The trick is to pull the front cover off by using a putty knife .slide it under the cover at both front corners.it will click on each corner.then pull front cover off .lift off the bottom catch hooks.look for the pump on the bottom right side.unplug the wite connector .take 2-5/16 bolts out holding the bracket.then grab a pliers .squeeze the hose clamps and pull the 2 hoses off.assemble new pump. Read more...
Your Price
$6.24
  In Stock
SCR 8-32 HXP 1/4 S
PartSelect Number PS2322292
Manufacturer Part Number WD02X10162
Your Price
$6.24
  In Stock
Screw
PartSelect Number PS261484
Manufacturer Part Number WD2X425
10-12 x 1/2 inch - Sold individually.

Related Parts