Hotpoint Dishwasher Spray Arms

Hotpoint Appliance Parts
Shop By Part Type

Popular Hotpoint Dishwasher Spray Arms

Your Price
$27.51
  In Stock
Lower Spray Arm Base
★★★★★
★★★★★
(9)
PartSelect Number PS1765974
Manufacturer Part Number WD12X10244
This part fits just under the fine filter assembly and supports the lower spray arm.
Fixes these symptoms
  • Not cleaning dishes properly
  • Not draining
  • See more...
Installation Instructions
Larry from Fort Worth, TX
Telescopic sprayer assembly in the Spray Arm Weld broke top element popped out
First off on this model, if one of the telescopic spray arm weld assembly comes out it is NOT repairable you have to replace the whole part.
The assembly on my model number was simple you do NOT have to PRY anything out...(I broke the base spray arm trying to shove a screw driver into the Spray arm weld.(You could try this but chances are the plastic will break and I recommend replacing both parts why not???.)
There are two bolts on the sump protector basket that has to be removed first. They are 1/4 inch.
Once that cover is free there is a bolt (also 1/4 inch) on the base spray arm it is easy to see but hard to get to I used a very thin open ended wrench
1/3 turn at a time till I could get the socket on it.
Next there is a rubber gromet like thingy that just pulls loose remove it also.
Next take the spanner wrench (I used one with a rubber belt) wrap around base spray arm and turn counter clockwise it just unscrews.

reassembly is simple but this is GE so I inspected the sump and found one medal impeller and one black screw at the bottom!!!!!
The impeller is threaded and just screws onto the shaft (look at the diagrams on this web site to see placement.)
Throw the screw away it does nothing except if left there jacks up the impeller I am guessing it fell out of some factory workers pocket.
If after you put all the parts back in and the washer does not drain check your reassembly if you don't line the parts up just right the unit will not drain.
Don't forget the rubber grommet (not sure what it does but it's easy to replace after all is assembled) also there is a metal washer that is inbetween the base spray arm and the spray arm weld put it back before you click those two parts together it protect the plastic from wearing it is a bearing!!
If you found this site you are doing really good This site had all the diagrams I was looking for I love you guys you so rock!!! I wish the diagrams were bigger but they were adequate. GE 's site was no help and I doubt I will ever buy another one from them.
Good luck just remember look at the parts diagrams before attempting the repair.
Read more...
Your Price
$34.77
  In Stock
Lower Spray Arm
★★★★★
★★★★★
(9)
PartSelect Number PS1765984
Manufacturer Part Number WD22X10055
This is a replacement lower wash arm assembly for your dishwasher. The lower spray arm is mounted to the bottom of your dishwasher tub and will rotate and spray water during the wash cycle. The spray arm has small holes that spray the water, and these can become clogged with debris and hard water buildup inside your dishwasher. The spray arm can also become jammed if silverware falls into the main tub during the cycle. These problems can cause the spray arm to malfunction, which will result in your dishes coming out of the dishwasher unclean. This part is made of white plastic and is sold individually.
Fixes these symptoms
Installation Instructions
Larry from Fort Worth, TX
Telescopic sprayer assembly in the Spray Arm Weld broke top element popped out
First off on this model, if one of the telescopic spray arm weld assembly comes out it is NOT repairable you have to replace the whole part.
The assembly on my model number was simple you do NOT have to PRY anything out...(I broke the base spray arm trying to shove a screw driver into the Spray arm weld.(You could try this but chances are the plastic will break and I recommend replacing both parts why not???.)
There are two bolts on the sump protector basket that has to be removed first. They are 1/4 inch.
Once that cover is free there is a bolt (also 1/4 inch) on the base spray arm it is easy to see but hard to get to I used a very thin open ended wrench
1/3 turn at a time till I could get the socket on it.
Next there is a rubber gromet like thingy that just pulls loose remove it also.
Next take the spanner wrench (I used one with a rubber belt) wrap around base spray arm and turn counter clockwise it just unscrews.

reassembly is simple but this is GE so I inspected the sump and found one medal impeller and one black screw at the bottom!!!!!
The impeller is threaded and just screws onto the shaft (look at the diagrams on this web site to see placement.)
Throw the screw away it does nothing except if left there jacks up the impeller I am guessing it fell out of some factory workers pocket.
If after you put all the parts back in and the washer does not drain check your reassembly if you don't line the parts up just right the unit will not drain.
Don't forget the rubber grommet (not sure what it does but it's easy to replace after all is assembled) also there is a metal washer that is inbetween the base spray arm and the spray arm weld put it back before you click those two parts together it protect the plastic from wearing it is a bearing!!
If you found this site you are doing really good This site had all the diagrams I was looking for I love you guys you so rock!!! I wish the diagrams were bigger but they were adequate. GE 's site was no help and I doubt I will ever buy another one from them.
Good luck just remember look at the parts diagrams before attempting the repair.
Read more...
Your Price
$101.44
  In Stock
Lower Spray Arm - Gray
★★★★★
★★★★★
(13)
PartSelect Number PS1020205
Manufacturer Part Number WD22X10047
The lower spray arm is mounted to the bottom of your dishwasher tub, and it rotates and sprays water to clean the dishes in the lower dish rack. This spray arm is made of gray plastic, and is approximately 20 inches in width. The lower spray arm will not spin if it has become clogged with debris and hard water deposits from your dishwasher, if it has become jammed by silverware, causing it to melt, or if the bottom of the spray arm has become disconnected from the bottom of the tub. If the spray arm encounters any of these issues, it will need to be replaced. To replace the spray arm, remove the lower dish rack and simply unscrew the old arm. Screw the new spray arm in until it locks into place.
Fixes these symptoms
Installation Instructions
Ric from Henderson, NV
Diswasher wasn't cleaning the dishs because the spray arms were clogged with calcium deposits.
Replacement of the arms is very simple, the bottom arm pulls out after turning it counter clockwise, no tool needed. The upper arms need the use of a nut driver or simlar tool to remove the hex screws holding them to the water supply tubes. The hardest part of the repair will be removing the top dish tray. This requires twisting the door slide end retainers outward to remove them and then the dish tray will slide out allowing easy removal of the arm. The top arm is mounted the body of unit.
This problem would not have occurred if there was an inline filter on the cold side to filter out calcium (whole house filter). Another way to have corrected this without the purchase of parts would be to run the dishwasher on the rinse cycle 3 or 4 times using 1 cup of lime away on each rinse and also by removing the arms and soaking the arms in a 50/50 solution of water and lime away for 24 hours. This will break down the calicum and enable the arms to be cleaned using a garden hose. New parts however save time and labor in cleaning the arms, however the main drain and supply lines to the arms still need the rinsing prior to replacing the new parts.
Read more...
Your Price
$11.20
  In Stock
Fine Filter Hub Nut
★★★★★
★★★★★
(1)
PartSelect Number PS259078
Manufacturer Part Number WD12X10061
This is the replacement fine filter hub nut for your dishwasher. It is made of white plastic and is approximately 3 inches in diameter. The fine filter hub nut is also known as the lower spray arm hub nut, and it connects the lower spray arm to the hub. If the hub nut breaks, it can cause the spray arm to wobble during operation and this can result in a strange noise. To replace this part, first remove the spray arm by turning it counter clockwise, then do the same with the hub nut. Install the new hub nut by turning it counter clockwise, then replace the lower spray arm. This part is sold individually and is an OEM part from the manufacturer.
Fixes these symptoms
  • Leaking
  • Noisy
  • Not cleaning dishes properly
  • See more...
Installation Instructions
Christopher from St Augustine, FL
Rate chewed drain hose up.
Removed screws that held dishwasher under cabinet...pulled out DW...removed old part...replaced with new....easier than falling off a stump. Read more...
Your Price
$17.17
  In Stock
Middle Spray Arm
★★★★★
★★★★★
(3)
PartSelect Number PS1015640
Manufacturer Part Number WD22X10046
Your dishwasher’s middle spray arm is connected to the top dish rack, and moves the water around to clean the dishes. If your dishwasher is noisy, or it is not cleaning the dishes properly, you may need to replace the middle spray arm. You should also replace the part if the holes on the spray arm are clogged, or the arm itself is cracked or broken. To replace the middle spray arm, simply unscrew the old spray arm and screw in the new one. This part is sold individually and is made of white plastic. It is approximately 20 inches in width.
Fixes these symptoms
Installation Instructions
Ric from Henderson, NV
Diswasher wasn't cleaning the dishs because the spray arms were clogged with calcium deposits.
Replacement of the arms is very simple, the bottom arm pulls out after turning it counter clockwise, no tool needed. The upper arms need the use of a nut driver or simlar tool to remove the hex screws holding them to the water supply tubes. The hardest part of the repair will be removing the top dish tray. This requires twisting the door slide end retainers outward to remove them and then the dish tray will slide out allowing easy removal of the arm. The top arm is mounted the body of unit.
This problem would not have occurred if there was an inline filter on the cold side to filter out calcium (whole house filter). Another way to have corrected this without the purchase of parts would be to run the dishwasher on the rinse cycle 3 or 4 times using 1 cup of lime away on each rinse and also by removing the arms and soaking the arms in a 50/50 solution of water and lime away for 24 hours. This will break down the calicum and enable the arms to be cleaned using a garden hose. New parts however save time and labor in cleaning the arms, however the main drain and supply lines to the arms still need the rinsing prior to replacing the new parts.
Read more...
Your Price
$6.30
  In Stock
SCR B-16 HXW 1/2 Stainless Steel
★★★★★
★★★★★
(1)
PartSelect Number PS2370492
Manufacturer Part Number WD02X10169
Fixes these symptoms
Installation Instructions
Jim from O BRIEN, FL
Middle spray arm not turning
One of the rack slide end caps broke so only one end cap kept the rack from falling out. The video guide worked for me to remove the remaining end cap allowing the rack to come out. I then replaced the middle arm conduit carrier as it no longer had a tight fit. I then replaced the middle spray arm bearing and reinstalled the rack and the rack slide end caps using the video supplied online by this site . Ran dishwasher and verified middle spray arm was turning. Read more...
Your Price
$46.78
  In Stock
Lower Spray Arm with Tower
★★★★★
★★★★★
(7)
PartSelect Number PS260603
Manufacturer Part Number WD22X154
This part comes with a three section power tower spray nozzle.
Fixes these symptoms
Installation Instructions
Paul from Tiger, GA
Lower spray arm cracked reducing it's effectiveness
The new arm was slightly different then the old arm. The problem was how to remove the old arm. Decidef to use an adjustable wrench much like a spanner wrench. A strap rench could also be used. Once the old unit was removed, the new lower spray arm screwed right in place. The entire process from PartSelect was easy and took less that a week including a weekend. Will definately use them again. Read more...
Your Price
$21.26
  In Stock
Pump To Wash Arm Rubber Connector
★★★★★
★★★★★
(3)
PartSelect Number PS259558
Manufacturer Part Number WD18X214
This connector has female threads.
Fixes these symptoms
Installation Instructions
Skott from Mason, OH
Dishwasher leaking at rubber connector - pump wash arm
First removed dishwaser from under counter so I could get to rubber connecter. It is located in center under dishwasher. I first needed to unscrew with wrench rubber connection at pump and and then the complete piece unscewed by hand from pump wash arm. I then just had to screw new rubber connector back on to bottom of dishwasher and re-attached at the pump. It was very easy to replace the rubber connector. I also replaced the dishwasher sump housing because it was made of same rubbber material and feared it was deteriorating also. I had to unscrew with wrench at pump as well and it just popped out from inside dishwasher after unscrewing screen inside dishwaser. Popped new piece in and screwed screen back on and reconnected underneath dishwasher back to pump. The rack roller wheel just popped right on. FYI: The wheel is actually 1.75 inches in diameter not 2 inches. I was worried it might be too big if it where 2 inches but it was the same size as the other wheels which was 1.75 inches. The hardest part of this job was getting the dishwasher in and out from under the counter. The good news is that most of these parts are standard and the replacement parts fit perfect. Read more...
Your Price
$42.26
  In Stock
Lower Spray Arm and Support Assembly
★★★★★
★★★★★
(3)
PartSelect Number PS260529
Manufacturer Part Number WD22X10008
This part comes with the telescopic tower.
Fixes these symptoms
Installation Instructions
sheila from dyersburg, TN
spray arm was cracked and the top part kept spraying off
just unscrewed it from the dishwasher with my hand and put the new one back on the same way Read more...
Lower Spray Arm Bearing
PartSelect Number PS258123
Manufacturer Part Number WD01X10107
This part is a replacement lower spray arm bearing for your dishwasher. It is made of gray plastic and is approximately ½ inch in diameter. The spray arm bearing reduces friction and allows the spray arm to rotate during the operating cycle. If the spray arm is not rotating or cleaning dishes properly, or the dishwasher is noisy during operation, you may need to replace the spray arm bearing. This is a bearing for the middle spray arm, which is mounted to the bottom of the upper dish rack. The bearing is made of metal and is approximately one inch in diameter. This part is sold individually and is an OEM part.
Fixes these symptoms
Installation Instructions
Ashraf from Merrick, NY
Leak from the bottom center
The connector pump had a pinhole leak at the seam (new part did not have seams). Also replaced the sump inlet which looked worn and the impeller.

Lay dishwasher on it's back to access the bottom. Loosen all clamps. Remove both U shaped holders on the sump inlet. Remove screws holding the drain motor. Pull out the pump motor and sump inlet. Connector pump can be unscrewed from the bottom.

Replace parts and reassemble. It isn't that bad once you start disassembly, especially for anyone somewhat handy.
Read more...

Related Parts