Crosley Range Hinges

Your Price

$76.14

Door Hinge - Left or Right Side

★★★★★

2 Reviews

PartSelect Number PS2088468

Manufacturer Part Number 74011142

Sold individually.

Fixes these symptoms

Door won’t close
See more...

Installation Instructions

Patrick from MORAGA, CA

Two digits on the touch pad didn't work "9" & "0". Went to utube and they said hinges go bad causing heat to leak affecting touch pad

Pull range out 6 inches. Open door to 45 degrees and pull up to remove door. Remove both side plates, two screws each side. Remove both hinges by loosening two small bolts on the front of range that connect to the hinges. Place new hinges in place. Bolt hinges using bolts you removed, replace side panels. Slide door on hinges and push back range. Read more...

Your Price

$72.90

HINGE

PartSelect Number PS2378959

Manufacturer Part Number 316575909

Installation Instructions

Alan from WAPPINGERS FL, NY

Unable to close oven door; door hinge needed to be replaced

Remove oven door and place on soft surface
Remove 2 Door Handle Screws
Remove 4 Inner and Outer Door Panel Screws
Remove Door Hinge Screws and remove door hinge
Install new hinge by aligning with holes and secure with screws
Re-join inner and outer door panels
Replace door handle
Replace bottom screws Read more...

Videos!

Your Price

$89.62

Door Hinge - Left or Right Side

★★★★★

6 Reviews

PartSelect Number PS11744424

Manufacturer Part Number WP74011141

This hinge can be used for either the left or the right side of the oven door. Sold individually.

Fixes these symptoms

Door won’t close
See more...

Installation Instructions

Lar from Cary, NC

Oven Door hinge broke

0. Throw oven circuit breaker 1. Open oven door and slide/lift door off of hinge posts 2. Remove oven drawer 3. Slide oven out from between cabinets and turn so that the back is accessible. 4. remove Phillips screws holding the cover-rear and side panel to the stove. Note which screws have pan heads and which are hex head. 5. remove stove elements and pans 6. Raise stove Top Assembly and release ceramic element sockets from their clips. 7. Push the supports for the Top Assembly fornt and back to release them from their sockets so that the Top Assembly can be lifted to near vertical. 8. Remove the hex head screw holding the Control Panel End Cap to the side panel. (Steps 5-7 might be avoided if you have a small socket wrench that can get to this screw without removing the elements.) 9. Remove the other screws holding the top of the side panel to the "Box Burner" pan that sits under the Top Assembly. 10. Pull side panel slightly away from the oven and lift it to disconnect it from the posts that hold the side panel to the front of the oven. 11. Remove the two screws on the front of the oven that hold the hing mechanism. 12. tilt and remove the hinge. 13. Open the replacement hinge so that it can fit through the hinge opening in the front of the oven. 14. Reassemble. Read more...

Videos!

Your Price

$94.54

Door Hinge - Left or Right Side

★★★★★

3 Reviews

PartSelect Number PS11744423

Manufacturer Part Number WP74011140

Each hinge is sold seperately.

Fixes these symptoms

Door won’t close
See more...

Installation Instructions

James from Elmont, NY

broken door hinge

unplug unit remove rear panel screws lift up stove top remove top two screws remove panel remove two hinge screws remove replace hinge and follow in reverse order Read more...

Your Price

$76.24

HINGE

PartSelect Number PS7784117

Manufacturer Part Number 316575911

Your Price

$56.04

Door Hinge

PartSelect Number PS2364193

Manufacturer Part Number 316566206

Sold individually.

Your Price

$79.21

Door Hinge - Left or Right side

PartSelect Number PS11744838

Manufacturer Part Number WP8053807

Use for painted door only. Sold individually.

Fixes these symptoms

Door won’t close
See more...

Installation Instructions

Earle from Taylorsville, UT

Both hinges were bent, probably from dropping the door, or leaning on it when it was in the down position.

1st; I opened the door, 2nd; removed the keepers that prevent the door from coming unhinged. 3rd; placed 2 short screws in the holes in the hinges. 4th; raised the door until it stopped. 5th; lifted the door upward and slid the hinges out of the slots in the range. 6th; laid the door face up on a microwave stand. With a handle on the outside, and hinges sticking out of the inside, it was inpossible to lay the door flat on a larger surface, and get around it. 7th; removed 2 screws from the inside top, and the 8 screws from the very bottom. 8th; removed the bottom rail, and the handle assembly. From there everything was stacked pieces. Picked the glass front up, and carefully set it safely aside. Picked each piece up and cleaned it, and started the re-assembly. The hardest part of the process was getting the fiberglass rope around the inside glass, to stay in place during the initial re-assembly. From there, the assembly was just the reverse order. the process was about 1 hour and 20 minutes, due to lack instructions and practice, plus cleaning, finding screws, and tools, Instructions may have been on line, but I didn't find them. The new hinges came with pins in place, and should have come with an extra set to lock the old hinges. Read more...