Crosley Range Thermostats

Crosley Appliance Parts
Shop By Part Type

Popular Crosley Range Thermostats

Your Price
$32.84
  In Stock
Oven Probe
★★★★★
★★★★★
(29)
PartSelect Number PS1528542
Manufacturer Part Number 316490000
This genuine OEM oven probe is also known as an oven temperature sensor or range probe. This part is manufactured for a range, stove, or oven to detect the temperature within the oven cavity. The probe allows the oven to maintain the set temperature by sensing the temperature and sending the information to the ovens motherboard. You may need to replace this part if oven is not heating or is heating unevenly. Be sure to disconnect power to oven before replacing, as it is an electrical part. Tools needed are 1/4 inch nut driver and needle nose pliers.
Fixes these symptoms
  • Element will not heat
  • Little to no heat when baking
  • Oven is too hot
  • See more...
Installation Instructions
Tim from ASHAWAY, RI
oven did not heat up
Replaced the probe because that's what this site recommended.The oven still does not heat up. Read more...
Your Price
$21.98
  In Stock
Oven Temperature Sensor
★★★★★
★★★★★
(12)
PartSelect Number PS12724046
Manufacturer Part Number 316217008
Note: Connector could be different than original. If so cut & splice wires together with porcelain wire nuts.
Fixes these symptoms
  • Element will not heat
  • Gas igniter glows, but will not light
  • Little to no heat when baking
  • See more...
Installation Instructions
MaryLou from Monroe, NC
Range would not come on
Turned off power, took back off stove removed old probe.
I had to splice wires since new probe ends did not match up.
the instructions were to splice the wires. I had the breaker off for about 3 hours. this is not in the instructions, but being a widow, I had to ask a few people why it would not come on after I connected the wires.
After waiting, I turned the breaker on and my range came back on.
Read more...
Your Price
$46.16
  In Stock
Long Oven Sensor
★★★★★
★★★★★
(15)
PartSelect Number PS1570174
Manufacturer Part Number 12001656
This long oven sensor is also commonly known as a temperature sensor. It is designed for use with ovens and ranges. It is similar to a thermostat; it measures and regulates the internal temperature of your oven cavity. There is an adapter at one end, a probe at the other, and they are connected by an insulated wire. The probe is approximately 7 inches long. You can test the sensor with a multi-meter for functionality. You need to check the model-specific manual to determine what the proper resistance is for your specific appliance. This oven sensor comes with two wire harness adapters and a set of instructions.
Fixes these symptoms
  • Door won’t open after self cleaning cycle
  • Element will not heat
  • Little to no heat when baking
  • See more...
Installation Instructions
David from Westford, MA
Oven not holding 350 F, when cooling the coils did not reheat
Removed the oven door by opening slightly, then pic door up to remove. Remove 2 screws holding oven sensor in place, gently pull on sensor to remove, had to remove about 8 inches to get at plastic connector. Unplug connector, had to use an adapter cable supplied with the PartSelect kit to install new sensor, push cable back into opening, reinstall 2 screws. The oven works fine! Note that due to thermal lag the temperature overshoots to 370 degrees and undershoots to 340 degrees, this appears to be normal oven operation. Putting door back in place was easy. Read more...
Your Price
$89.53
  In Stock
Oven Sensor
★★★★★
★★★★★
(17)
PartSelect Number PS11749737
Manufacturer Part Number WPW10181986
This oven temperature sensor, for ranges, works together with the oven control board to measure and regulate the oven temperature. The sensor detects the temperature in the oven cavity. If the following symptoms occur, replacing the temperature sensor could be the solution: Little or no heat when baking, oven not heating evenly, oven will not start, and/or oven is overheating. Often, if the sensor is defective, the oven temperature will fluctuate and be inaccurate by more than 50 degrees. The tool needed for this replacement is a #2 square head screwdriver or a #2 Philips screwdriver. Remember to unplug the range before installing the part.
Fixes these symptoms
  • Element will not heat
  • Little to no heat when baking
  • Little to no heat when broiling
  • See more...
Installation Instructions
Ruth from Oregon, IL
temperature not accurate after 3 1/2 years of happy usage
Opened up the back of the stove. Unpluged the sensor. Replaced the sensor. Replace the back of the stove.

The sensor that has been replaced is not what is expected. After reading all of the instructions for adjusting the temperatures, the only temp that stays steady is when we first turn on the oven to 350 degrees. That stays steady but when I turn it to 400 it slowly goes up to 425 degrees.
Read more...
Your Price
$39.57
  In Stock
Oven Temperature Sensor
★★★★★
★★★★★
(4)
PartSelect Number PS1528543
Manufacturer Part Number 316490001
The temperature sensor detects the temperature within the oven cavity. If there is a limited amount of heat, it is not heating evenly, or the oven will not start, this might indicate that your temperature sensor requires a replacement. If you are working with your oven this part is found on the right side when facing the back of the oven. This part is can be found in a range, wall oven, and microwave-oven. You will need to remove the panel located on the back of the oven, unplug the sensor, remove the screw, and pull the sensor out. The new one slides into place.
Fixes these symptoms
  • Element will not heat
  • Little to no heat when baking
  • Oven is too hot
  • See more...
Installation Instructions
Russell from Lake Havasu, AZ
Above 400 beeper went off & code numbers came up on read out
Cut off power at fuse panel. pulled stove out from wall went behind stove removed back panels in area of sensor that I could see from the front side, inside oven. Located sensor from rear & unpluged senser from wiring bundle reached inside oven & removed screws from sensor. Pulled sensor out & threaded wire through hole. Took old & new sensors to bench in shop. Plug on new not the same as old. Had to change plug Cut and stripped wires. Wire is very small, need to use a good stripper. Twisted wire together & soldered connection, used shrink wrap to insulate wire. Took part inside and reinstalled in reverse order. Used 1/4 inch nutdriver on total job start to finish. Read more...
Your Price
$69.85
  In Stock
Oven Thermostat - 125V 60Hz
PartSelect Number PS2339203
Manufacturer Part Number 316032411
This part establishes and maintains the internal temperature of the oven cavity.
Fixes these symptoms
  • Gas igniter glows, but will not light
  • Little to no heat when baking
  • Oven is too hot
  • See more...
Installation Instructions
Thomas from Pinehurst, MA
Oven would heat up in the off position.
Oven thermostat was bad comes with copper tube, to register the oven temp. Un pluged the wire to the electronic pilot. Removed the face plate, six screws, feed the copper tube thru the oven and stove top. Unscrewed the thermostat, install the new thermostat fed the tube back thru snaped it in place, connected the wires and everything was fine. Oven is now working fine.. Read more...
Your Price
$159.58
  In Stock
Oven Thermostat
★★★★★
★★★★★
(1)
PartSelect Number PS899636
Manufacturer Part Number 316215900
Your Price
$176.09
  In Stock
Thermostat
PartSelect Number PS899637
Manufacturer Part Number 316215901
This part establishes and maintains the internal temperature of the oven cavity.
Your Price
$193.61
  In Stock
Oven Thermostat
PartSelect Number PS442276
Manufacturer Part Number 318059310
This part establishes and maintains the internal temperature of the oven cavity.
Your Price
$154.83
  In Stock
Oven Thermostat
PartSelect Number PS11744075
Manufacturer Part Number WP74005019
This part establishes and maintains the internal temperature of the oven cavity.
Fixes these symptoms
Installation Instructions
Cindy from Uniontown, AR
oven woulfd not shut off when temp reached
very to install thermostat and probe...took about 30 mins. with the old therm exposed i just disconnected the wires one at a time reconnecting onto new therm one at a time...works great now. Read more...

Related Parts