Crosley Range Valves

Crosley Appliance Parts
Shop By Part Type

Popular Crosley Range Valves

Your Price
$39.22
  In Stock
LP Conversion Kit
★★★★★
★★★★★
(1)
PartSelect Number PS3633782
Manufacturer Part Number GRLP4
The LP conversion kit is used in ranges
Installation Instructions
James from KENSINGTON, OH
BAD LIGHT SOCKET
Repaired under warranty Read more...
Your Price
$38.32
  In Stock
Natural Gas to Liquid Propane Conversion Kit
★★★★★
★★★★★
(7)
PartSelect Number PS2351422
Manufacturer Part Number GRLP3
This kit is used to convert your appliance to liquid propane.
Installation Instructions
Denny from Bishop, CA
Bought a new gas oven that did not come with a propane conversion kit.
I followed the simple instructions that were included in the kit. I started by replacing the 5 orifices on the top burners. The orifices are well labeled with numbers and colors. Next, I tightened the broiler burner orifice and the oven burner orifice with a 1/2 inch wrench. I had to tighten them pretty good to get the flame down where it is supposed to be. Then, I checked for leaks and I was then ready to cook. Read more...
Your Price
$19.41
  In Stock
Left Front Orifice - 9.5K
★★★★★
★★★★★
(2)
PartSelect Number PS2332664
Manufacturer Part Number 316527500
Your Price
$40.44
  In Stock
Pilot with Thermocouple
★★★★★
★★★★★
(8)
PartSelect Number PS11750349
Manufacturer Part Number WPW10206112
The pilot stays lit all the time and, when the oven is turned on, the flame gets bigger and surrounds the thermocouple. When the thermocouple senses the required heat, the safety valve opens to let the gas flow to the oven burner tube where the pilot flame ignites the gas.
Fixes these symptoms
  • Gas igniter glows, but will not light
  • Little to no heat when baking
  • Will Not Start
  • See more...
Installation Instructions
Peter J from Brooklyn, NY
Pilot Light Won't Stay Lit
First I removed the oven door by pulling straight up off of the hinges in the open postion. Next remove oven racks,then use 1/4 nutdriver to remove back screws on inside oven bottom plate. Next remove gold nut on silver tube @ pilot connection,then remove 1/4 nuts that hold pilot assembly. Next open top of stove and remove small gold nut "with the thin wire from pilot"attached to the back left of oven control knob. Snake that nut and wire from the top of the stove down to the oven and removethe whole pilot assembly. To install carefully unroll the new pilot assembly starting from the oven "there are two round holes you need to snake the tube into"and up behind the back & into the stove top. Make your connection@ the oven assembly. Next attach the assembly with the 1/4 screws that you removed,then make your connection"gold screw silver tube" now push in your oven control knob to alllow gas to flow to the pilot tube and check for leaks with a water @ soap solution. No bubbles no leaks. Light your pilot . . . . You must hold in the oven knob. Put back in oven plate,,,, 1/4 screws,,,,racks close the stove top ,put door back on hinges and your done. . . . . Hope I helped,. . Pete Read more...
Your Price
$15.11
  In Stock
Right Rear Orifice
★★★★★
★★★★★
(1)
PartSelect Number PS2349573
Manufacturer Part Number 316527504
Your Price
$22.29
  Special Order
Medium Burner - 9.5K
★★★★★
★★★★★
(2)
PartSelect Number PS439737
Manufacturer Part Number 316212400
The surface burner head is used for ranges and ovens, and is located on the cooktop, where the flames go up. The surface burner spreads the gas through holes to create an even flame throughout the entire cooking area. If your surface burner is damaged it can affect the distribution of gas, or the flames may not come up correctly. If this is the case, replace this part. The measurements of the surface burner are: 6.25 inches in length, 5.13 inches in width, 8 inches in height, and 0.4 pounds in weight. Allow your cooktop to cool before installing this part. Refer to the manual provided by the manufacturer for further repair instructions.
Your Price
$56.88
  In Stock
Front Burner
★★★★★
★★★★★
(4)
PartSelect Number PS11770472
Manufacturer Part Number 5304506427
This is a front burner assembly for the stovetop on your range. It delivers the gas to the main cooking area by dividing it through the slots or holes in order to create an evenly burning flame. Take note that this is a front burner assembly. If you are looking to replace your rear burner assembly, see that in the related parts section. This model is roughly 8 inches long, 4 inches wide, and 4 inches thick.
Installation Instructions
PATRICIA from OPA-LOCKA, FL
One of the two front burners was broken and the second was leaking gas.
Unplug the old ones and the new ones snapped into place. Read more...
Your Price
$52.46
  Special Order
Front Burner Igniter/Orifice Assembly
★★★★★
★★★★★
(3)
PartSelect Number PS2332312
Manufacturer Part Number 316237805
This igniter and orifice assembly is a legitimate OEM replacement part for your gas stove, and includes the igniter, orifice assembly, and gas tube. This part may need replacing if the igniter fails or the tube is leaking gas. It is a very easy repair. Remove the grates and burners from the range. Unscrew the existing assemblies and pry off the cooktop. Locate the assembly you are replacing and undo the nut holding it in place. Pull out the igniter wire by hand, and install the new one, replacing the rest of the parts in reverse order.
Fixes these symptoms
  • Element will not heat
  • Gas igniter glows, but will not light
  • Will Not Start
  • See more...
Installation Instructions
Steve from NORTH PEKIN, IL
the new burners had no threads for the screws
had to use a tap and cut new threads. Also had to remove the top of the range, and the metal cover under the top. Read more...
Surface Burner Cap - Black - Small 5K
★★★★★
★★★★★
(6)
PartSelect Number PS2581737
Manufacturer Part Number 316261704
Sold individually. This part helps the flame to spread for even heat. Also protects your burner head from spills.
Surface Burner Cap - Black
PartSelect Number PS2581740
Manufacturer Part Number 316261804
Sold individually. This part helps the flame to spread for even heat. Also protects your burner head from spills. The surface burner cap is located on the top of the burner head and is used in ranges and ovens. The burner cap helps spread out the burner flame for even heating, and protects the burner head from cooking spills. Without the cap you can have a burning gas torch. If your cap is missing or is discolored, replacing this part can solve the issue. This part comes in the color black. Remember to unplug your range from the power source and allow surface to cool before installing this part. Refer to the manual provided by the manufacturer for further installation instructions.

Related Parts