3146 - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Washer was stopping during the spin cycle and making a grinding noise.
2 of 2 people
found this instruction helpful.
-
Mike from MANOR, TX
- Really Easy
- Less than 15 mins
-
Screw drivers
Our Samsung HE washer started making a grinding noise and stopping at the end of the rinse/spin cycle. I had replaced the clutch and seal 2 years ago and it sounded like it was going out again, however we were not getting the gunk inside the tub like before (seal) and the machine was throwing the tE error code when it stopped which it di
... Read more
d not do last time. According to the manual this meant a thermistor error and the solution was "Call for Service". The machine is 9 years old and way out of warranty so....uh No! I ordered the new thermistor for $15 plus shipping to correct the tE code before looking to replace the clutch again or get a new machine. The new thermistor arrived, leaned the machine on its back, unplug one connector, remove two screws and pull the old one out of it's hole, push the new one in, replace two screws and the connector and GO! Problem fixed! No tE code, no stopping, no grinding noise. As best I can tell, the old thermistor was faulting during the spin cycle and the machine went into emergency stop mode which made the grinding noise. It was not the clutch or bearing at all. Most of the repair time was moving the machine out and disconnecting lines so I could lean it onto its back. Note: If your machine is stopping before draining, it will have water inside the tub which will drain out of the hole where the thermistor goes when you pull the old one out. It has an o-ring to seal it, so just expect a little water to come out and be ready to catch all the water or put the new one in quickly.
Read less
Was this helpful?
Thank you for voting!
The base assembly was broken because it’s plastic.
2 of 2 people
found this instruction helpful.
-
James from ST MARIES, ID
- Really Easy
- Less than 15 mins
-
Screw drivers
The base assembly was easy to repair tip the washer on its side and took the screws out the bottom and two wires and a sensor off the old base assembly that was broken and replaced it the the way I took it off easy install. And they got great costumer service as well will be back for other parts.
Was this helpful?
Thank you for voting!
broken shelf end caps- right side of 2 shelves.
2 of 2 people
found this instruction helpful.
-
William from PRESQUE ISLE, ME
- Really Easy
- Less than 15 mins
After watching video I took off end shelf caps. It took close to 10 mins to replace them.
Was this helpful?
Thank you for voting!
lights blown out
6 of 14 people
found this instruction helpful.
-
Gerald from WINTERVILLE, GA
- Very Easy
- Less than 15 mins
replaced lights in refrigirator and freezer
Was this helpful?
Thank you for voting!
light wouldn't come out of socket
3 of 5 people
found this instruction helpful.
-
Joyce from Tacoma, WA
- Really Easy
- Less than 15 mins
It just unpluged and the new one plugged in. Simple. The part was reasonable and arrived very quickly. It sure is nice to have a light in the frig again.
Was this helpful?
Thank you for voting!
freezer stoped freezing
2 of 2 people
found this instruction helpful.
-
paul from ENDICOTT, NY
- Very Easy
- 15 - 30 mins
-
Pliers, Screw drivers
my freezer quit freezing, it would freeze for one day, thaw the next, so I went online, found PARTS SELECT, LOOKED UP MY MODEL #, come to find out it needed three parts to keep my freezer to freeze, first part was a thermistor a small PART took me longer to remove all the covers, and shelving, PULLED THE
... Read more
OLD OUT, CUT THE WIERS TO SIZE, AND REINSTALLED, IT WELL! THAT WASN'T ENOUGH THE FREEZER STILL DIDN'T FREEZE IT THOUT IT WAS A COOL WORMING OVEN, HAD TO INSTALL THE THERMISTOR I, SO I DID, TEN MIN, NOW I THOUGHT THAT WAS IT BECAUSE IT STAYED FROZEN FOR A WEAK, HAVE YOU EVER EATEN SOUPY ICE CREAM? SO BACK TO PARTS SELECT, THIS TIME I BOUGHT ONE MORE PT, THE RUN CAPACITOR, FIVE MIN, THAT/S ALL IT TOOK TO INSTALL. I DID NOT KNOW AT THE TIME YOU NEED THE THREE OF THEM TO RUN THE FREEZER ONE TO KEEP THE TEMP., ONE TO KEEP THE FAN RUNNING THE WAY IT SHOULD, AND THE THIRD TO MAKE SURE THE OTHER TWO KEEP RUNNING. NOW I CAN SET IT AT 4- 5 AND. FREEZE.
Read less
Was this helpful?
Thank you for voting!
The Refridgerator and Freezer were not cooling.
2 of 2 people
found this instruction helpful.
-
Frank from VERO BEACH, FL
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Installing the part repaired the fridge and freezer immediately.
Was this helpful?
Thank you for voting!
leg broke off inside housing
5 of 12 people
found this instruction helpful.
-
thomas m from CARMICHAEL, CA
- A Bit Difficult
- Less than 15 mins
raised the front of washer by hand (literally) and placed two 2x4 blocks under front lip for support. reached up inside washer cabinet and unscrewed the broken leg piece upwards into the cabinet. this was the only way I could get the broken piece out without some specialized tool to reach it from the underside. replacement with the new
... Read more
leg was a breeze.
Read less
Was this helpful?
Thank you for voting!
Drain hose had a pin hole leak external to washer
3 of 6 people
found this instruction helpful.
-
Terry from SIMI VALLEY, CA
- Really Easy
- 30 - 60 mins
-
Screw drivers
Very close to the installation video online at Parts Select. Removed the back panel, unclipped the hose from the inner fitting and replaced with the rear hose. Why it didn;t leak on the inside is interesting as there was no clip on the at the inner fitting.
The one difference from the existing install video online was that I didn't ... Read more have to tip the washer over ~75 degs before replacing. I instead found that I could put to cinder blocks under the back edge to replace the drain hose. This made the job quicker without having to worry about having a box for it to rest on (with any risk of falling to the floor).
The one difference from the existing install video online was that I didn't ... Read more have to tip the washer over ~75 degs before replacing. I instead found that I could put to cinder blocks under the back edge to replace the drain hose. This made the job quicker without having to worry about having a box for it to rest on (with any risk of falling to the floor).
Read less
Was this helpful?
Thank you for voting!
very dirty under adjitator cap and pulsator
3 of 7 people
found this instruction helpful.
-
Daniel from EDWARDS, IL
- Very Difficult
- 1- 2 hours
-
Wrench set
Tried to remove adjitator but it was stuck. Could not find any professional method of pulling it. There must be some type of puller,
Was this helpful?
Thank you for voting!
Lights did not work, bulbs were good
1 person
found this instruction helpful.
-
Donita from O FALLON, MO
- Easy
- Less than 15 mins
-
Screw drivers
Took out the light sockets, plugged in the new ones. I found the manual on line to find the part numbers. Parts select parts were perfect
Other Parts Used:
Was this helpful?
Thank you for voting!
bulb out
1 person
found this instruction helpful.
-
Kenneth from Rowe, VA
- Really Easy
- Less than 15 mins
I ordered the part, within two days we had received it. My husband put the part in and I really don't know what he used doing so. All I know is that the light works now and we don't have to use the flashlight. Thanks a lot.
Was this helpful?
Thank you for voting!
My light in the refrigerator was going on and off.
1 person
found this instruction helpful.
-
Nan from PURCELLVILLE, VA
- Very Easy
- Less than 15 mins
I unplugged the refrigerator. Pressed the tab near the light bulb. Unplugged the socket and reconnected it.
Was this helpful?
Thank you for voting!
The light inside the oven had burned out
3 of 7 people
found this instruction helpful.
-
Catherine from SEATTLE, WA
- Very Easy
- Less than 15 mins
0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
... Read more />3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.
No tools needed, the cap is just held in place with pressure from the wire.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
... Read more />3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.
No tools needed, the cap is just held in place with pressure from the wire.
Read less
Was this helpful?
Thank you for voting!
Fridge light dead even with new bulb
1 person
found this instruction helpful.
-
marj from NEWBURY PARK, CA
- Really Easy
- 15 - 30 mins
-
Screw drivers
1- youtubed the potential diagnoses, 2- resourced and ordered parts, 3- removed old socket, installed new one :-)... My fridge is an older fridge and could've used a screwdriver for eyeglasses. Plug and play easy... YAY!
Was this helpful?
Thank you for voting!