EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

3146 - Instructions

All Instructions for the 3146
61 - 75 of 114

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Start relay burned
1 person found this instruction helpful.
  • Carlos from Copper Canyon, OK
  • Very Easy
  • 15 - 30 mins
  • Screw drivers
Unplug the refrigerator removed the condenser/ compressor cover back bottom on fridge, remove the relay from the compressor took off the two wires, replace with new relay
Was this helpful?
Thank you for voting!
Washer water would not stop running
1 person found this instruction helpful.
  • Willie from Loganville, GA
  • Very Easy
  • 15 - 30 mins
  • Nutdriver, Pliers, Screw drivers
Turn water valves off , remove the hoses from washer,remove covering from hose housing, remove the claps from back off housing, remove screws from intake housing, remove iPod intake and install new housing and reverse the install
Was this helpful?
Thank you for voting!
water leaking from under dishwasher
1 person found this instruction helpful.
  • Edward from E LONGMEADOW, MA
  • A Bit Difficult
  • 30 - 60 mins
  • Pliers, Socket set, Wrench (Adjustable)
Water was leaking from under the GE dishwasher, but once we pulled it out, had apparently been going on for a little while. Turning the water off to the dishwasher made it stop, so it was happening even when the unit was not running, potentially indicating somewhere early in the path of the water to and into the machine.

Indeed , inspecting the water inlet vale showed a slow leak. Getting the replacement part was fine, and it fit the electrical, water inlet (existing 90-degree water inlet elbow), and water outlet connections just fine - but the original machine screws that held on the original water inlet valve did not work. It took a little research to figure out the new type of screw required, which was apparently a 10/16 Type AB, which seemed to be a less common type of sheet metal screw (with a point), as opposed to the original flat-ended machine screws. So, after ordering those separately (which were a bit expensive), it went together fine.

A note on the water inlet valve part just indicating the the threading on those parts has changed over time, so potentially ordering the screws to attach it might be worthwhile, would be good information to add about the water inlet valve.
Was this helpful?
Thank you for voting!
Cold water valve leaking.
1 of 2 people found this instruction helpful.
  • Ken from Lakeside, CA
  • A Bit Difficult
  • 30 - 60 mins
  • Pliers, Screw drivers
turn off the water, unplug washer from power. remove two screws holding rear top plate. Here's the hard part. Pry the rear top plate from the top of the washer. It has multiple snap in guides across the front edge and they are very tight. Be careful and apply steady pressure straight up and they will eventually come free.
I mark ed each of the electrical inputs going to the old valve before removing. Remove the wiring harness. Again be careful and ease them off. the connectors
come apart easily. Remove the hose clamps with pliers and slip off the hoses. They are long enough that I trimmed off the soft ends of the old hoses and still had plenty of hose to reconnect. Remove the filler hoses. Remove the screws holding the valve to the machine. Re install the new valve in reverse order. Goes back in very easily.
Make sure to secure all the hoses. Run a wash cycle with an empty tub to make sure everything is working properly and nothing is leaking. Snap the rear top plate back into position and secure with the two screws Should take less than a couple of hours to do this job. Again the hardest part is getting the rear top plate off.
Was this helpful?
Thank you for voting!
could not get the 10 mm nut to loosen
1 of 2 people found this instruction helpful.
  • Marilyn from THOMASTON, GA
  • Very Difficult
  • 30 - 60 mins
  • Nutdriver
Tried everything and could not get it out I just use mesh bags for washing at this time, but LG washing machine is the worst I have ever had
Was this helpful?
Thank you for voting!
Gave LE code
1 of 2 people found this instruction helpful.
  • Michael from SAINT LOUIS, MO
  • Really Easy
  • 15 - 30 mins
  • Socket set
Former LG repair looked under washer while it was engaging & noticed motor was not spinning. LG took forever I ordered the part from you guys. It looked different from original. Figured out to take extra port for front loader. I have top loader. Installed washer works great!!
Was this helpful?
Thank you for voting!
Washer pulsator was coming loose during wash cycle.
1 of 2 people found this instruction helpful.
  • Kristen from Safford, AZ
  • Really Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
Since the old pulsator had actually come off during a wash cycle, I was able to place the new one on easily. Tightened the screw with a socket. Then placed the new cap on. Before placing the new pulsator on, I was able to clean all the mold and hard deposits off the mechanism under the pulsator. The hard deposits were also scrapped from the pulsator holding (where the screw goes) which may have caused the problem to begin with.
Was this helpful?
Thank you for voting!
Short in the light socket.
1 of 2 people found this instruction helpful.
  • ED from ENON, OH
  • Very Easy
  • Less than 15 mins
Un Plugged the frig. Unlocked the socket by pressing down on the latch. Pulled the socket out ensuring I had enough slack. Unplugged the old socket installed the new. Plugged the frig back in. Tested the switch . Very easy-to-use.
Was this helpful?
Thank you for voting!
Door shelf clip had broken
1 of 2 people found this instruction helpful.
  • Erika from Joliet, IL
  • Really Easy
  • Less than 15 mins
This shelf has been broken for about a year now and my husband tried several little quick fixes that would work for a while and then the shelf would fall again. A quick search online led me to your website, the part arrive within two days, and the shelf was fixed in less than ten minutes. It's working great. We'll definitely keep you in m ind for the future.
Was this helpful?
Thank you for voting!
Washing machine was displaying te code. Quick google search to diagnose the issue.
1 of 2 people found this instruction helpful.
  • Richard from DICKSON CITY, PA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Very simple repair after watching YouTube video on how to complete repair.
Was this helpful?
Thank you for voting!
The control board generated clicking noise. Temperature display wrong values.
1 of 2 people found this instruction helpful.
  • QUOC-LOC from LYNN HAVEN, FL
  • Really Easy
  • 30 - 60 mins
  • Screw drivers
On the internet forum I read that if the control board needs to be changed , do the same for the Run Capacitor/relay.
The Ge profile refrigerator was 15 years old. First I disconnect the power cord,
I removed the control board at the back of the fridge, replaced it with a new one and did the same for the run capacitor.
P lugged the power cord back and it works fine. GE repair service did not want to come to do it. DIY is fine.
Was this helpful?
Thank you for voting!
Change bulb
3 of 8 people found this instruction helpful.
  • Louis from LEAGUE CITY, TX
  • Really Easy
  • 30 - 60 mins
  • Nutdriver
Easy
Was this helpful?
Thank you for voting!
During the spin cycle water continued to flow into the machine.
1 of 3 people found this instruction helpful.
  • Jim from Crystal Lake, IL
  • Really Easy
  • 30 - 60 mins
unplugged machine, turned off water valves. Moved machine away from the wall. Disconnected supply lines. Removed cover housing water valve assembly.
Took a picture with phone. Disconnected water and electrical wires. Removed water valve assembly . Installed new assembly ,cover and reconnected supply lines, plugged power cord in, turn ed on water supply valves. Done.
Was this helpful?
Thank you for voting!
socket had melted
1 of 3 people found this instruction helpful.
  • Chris from Charlotte, NC
  • Really Easy
  • Less than 15 mins
pluged the wire harness into the new socket from the back and snaped the socket in place.
Was this helpful?
Thank you for voting!
The end cap on the door shelf snapped off.
0 of 1 people found this instruction helpful.
  • Miranda from Waterford, CT
  • Really Easy
  • Less than 15 mins
I pulled off the broken piece, ordered the new piece, and snapped it on. VERY SIMPLE.
Was this helpful?
Thank you for voting!
All Instructions for the 3146
61 - 75 of 114