This 40-Watt light bulb is sold individually.
It is specially designed to withstand extreme temperatures, so this bulb is compatible with a variety of appliance types including refrigerators, ranges, microwaves, and dryers. It features a frosted glass bulb with a standard metal socket base, which allows you to easily unscrew the burnt-out light and twist the new bulb into place.
Support steady compressor operation with this refrigerator run capacitor. It provides the electrical phase shift needed for the compressor motor to run properly as the cooling system operates. A failing capacitor may contribute to humming, difficulty starting, interrupted compressor operation, or rising compartment temperatures. Visible s...Read morewelling, leaking, or burned terminals may also indicate damage. Unplug the refrigerator before accessing the component. Capacitors can retain an electrical charge after power is disconnected, so follow approved discharge procedures and avoid touching or shorting the terminals. Record the wire positions before replacement. This is an OEM part sourced directly from the manufacturer.
This is an authentic LG water inlet valve for a top-load washer. It is designed to control the flow of water into the washer. If your washer is filling slowly, making loud noises, overflowing, or stopping in the middle of a cycle, you may need to replace the water inlet valve. Be sure to disconnect the power and water supply before you begin this repair.
This defrost timer will cycle for 25 minutes after every six hours of run time. The timer itself is made of plastic, and its terminals are bent, the leads are internal, and the label is orange. If you notice that your fridge is too warm, the fridge is running for a long time or is leaking, it could be due to the defrost timer becoming ina...Read morective. The defrost timer is found underneath the light cover (may need to remove lightbulb) and will need to be removed along with the air inlet assembly and housing.
This is a package of twelve Phillips-head screws. They can be used as replacement screws in refrigerators, ice makers, or freezers. Be sure to check that your appliance model is compatible with these screws. The screws are approximately ¾ of an inch in length.
This part is a replacement light socket for your refrigerator. It connects to the power source, and holds the light bulb. If the light in your refrigerator is not working, you could have a faulty socket. It is important to determine if the light bulb is simply burned out, or if the socket is causing the issue. Be sure to disconnect your r...Read moreefrigerator from the power source before you begin this repair. This socket is black in color and is sold individually. This is an OEM part sourced directly from the manufacturer.
Clothing moves over a covered mounting point with help from this washer pulsator cap. The round plastic cover snaps into the center of the washplate, concealing the mounting bolt and providing a smooth surface above it. Cracks, broken retaining tabs, or a missing cap may expose the hardware or allow the cover to come loose during washing....Read more Replacing a damaged cap restores the finished washplate surface and helps keep garments from catching around the recessed bolt opening as laundry moves through the wash cycle. This is an OEM part sourced directly from the manufacturer.
This is a pulsator assembly, also known as an agitator, for your washing machine. This pulsator sits at the bottom of your washer and is what is used as the main driving force to wash your clothes. If the pulsator in your washer is broken, it will need replacing immediately to continue to wash and clean your clothes evenly. The cap that sits in the center of this part is sold separately.
Drain used wash water with this top-load washer drain pump assembly. Its motor drives an internal impeller that pushes water from the tub through the drain hose during drain and spin cycles. A worn motor, damaged impeller, or leaking housing may cause standing water, slow draining, loud buzzing, or puddles beneath the machine. Replacing a...Read more faulty pump helps restore proper drainage so wash cycles can finish normally. Unplug the washer, shut off the water supply, and prepare for leftover water before disconnecting hoses or wiring. This is an OEM part sourced directly from the manufacturer.
This washer tub-to-pump drain hose carries used water from the outer tub to the drain pump during draining. Its flexible, corrugated design accommodates tub movement while keeping water contained within the drainage path. Cracks, splits, or worn sections may cause leaks beneath the washer, while a collapsed section can restrict flow and l...Read moreeave water in the tub. Replacing a damaged hose helps restore proper drainage and a secure connection between the tub and pump, allowing wastewater to move out during wash and rinse cycles. This is an OEM part sourced directly from the manufacturer.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
No power to the fan and compressor
222 of 302 peoplefound this instruction helpful.
Christian from Kearneysville, WV
Really Easy
Less than 15 mins
Screw drivers
I have a fridge in my garage. I have found that a glass of ice water or a cold drink outside is very important to me. When I discovered melting ice dripping onto the garage floor I was very upset. I spun the fridge and found that the compressor and fan weren't starting. I got out my multi-meter and discovered that power was not makin
... Read moreg it to these components. I did some research and found the wiring diagram online. There really isn't too much going on with a fridge and the most likely candidate seemed to be the run capacitor. I ordered the part, replaced it in a few minutes and the fridge began working again.
refrigerator was not cooling but the freezer worked fine.
93 of 110 peoplefound this instruction helpful.
Wanda from Cabins, WV
Really Easy
15 - 30 mins
Nutdriver, Screw drivers
My husband put on the defrost timer. At first I thought the part was not going to fix the problem. After about 5 hours my refrigerator was still warm. I went to work and when I got home that evening my refrigerator was cooling and down to 28 degrees. So if you replace this part wait at least 12-24 hours. Give it time to stablize.
... Read moreMy husband says it has to go through its cycle. It works on a 24 hour timer. My refrigerator is working fine and this has saved me alot of money. My husband says, once you put on the timer you may have to use a flat screwdriver and turn the small dial clockwise one click to start it. He removed the kick grill and replaced the part. Dont forget to shut breaker off to replace this part. Turn power back on and start the timer. We are so happy that we now have a working refrigerator.
Read less
Was this helpful?
Thank you for voting!
display showed dE
75 of 119 peoplefound this instruction helpful.
Nancy from Hamburg, NY
Easy
Less than 15 mins
Nutdriver
popped off front grille, removed 2 screws for bracket, then had to remove one screw for timer. unplugged old timer, reversed procedure, all works.