3146 - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Water inlet was leaking
5 of 6 people
found this instruction helpful.
-
Philip from CHULA VISTA, CA
- Really Easy
- 30 - 60 mins
-
Screw drivers, Wrench (Adjustable)
I noticed that my washer was leaking water into the tub. It was dripping, very slowly, but it was dripping. I noticed first, because it was starting to smell, and I didn’t understand why. Once I noticed that it was dripping, I checked online and noticed that the solenoid water inlet is most likely the problem. I found the part on parts, s
... Read more
elect, and confirmed with my model. The pictures were very close and similar, so I was pretty sure I was getting the cracked part. Once I received the part, it was time to fix it. You just have to turn the water supply off, remove the inlet lines with a adjustable wrench, if necessary, and then get to the washer. Make sure you also unplug the washer. There are only two Phillips head screws to remove to get the vanity cover off of the back. For whatever reason my removal was a little bit difficult for this. There are some plastic clips that hold the front portion on of the vanity plate. These were very tight, and I was afraid I would break them, but eventually they came loose with gentle upward pulling. Once this was off, it was super easy to identify the part that needed replacement. There are two hose clamps that you just need a pair of pliers to squeeze in slide off the hose. Then you remove three additional Phillips head screws, and the other connections pop out on their own. The solenoid plugs are very simple to slide off, and it is really difficult to put them on any other way. If you need to, you can take a few photos of the installation. Once you have the old one out, hook up the hoses first, and slide the hose clamps back to their original position. Once you have the two black hoses back on, reposition the new valve body, and slide the additional three prongs into the inlet soap dispenser. Make sure that the fit is snug. Don’t over push, the parts are plastic. Once this is done, reinsert, the three Phillips screws into their holes. Then you can reconnect the solenoids. At this point the replacement is done, and all you have to do is replace the vanity cover. Take time to ensure that you’ve done this correctly. I left the vanity cover off and ran a test load of dirty clothes to make sure that there were no leaks. Once I assure, there were no leaks, I put the vanity cover back on and put the two screws on. This was a very easy fix. Again, just go slow removing the vanity plate so you do not crack or break the tines in the front.
Read less
Was this helpful?
Thank you for voting!
Lots of loud noises when washing and spinning.
5 of 6 people
found this instruction helpful.
-
Ken from CALDWELL, ID
- A Bit Difficult
- More than 2 hours
-
Screw drivers, Socket set
Getting the old part out was not too hard, but had a couple challenges. Watched a video from RepairClininc that detailed the process very thoroughly. Definitely use an impact gun to remove the drum nut inside the drum. My drum was stuck on the shaft pretty good. Would not lift off. Removed the rotator, stator and diverter motor on the
... Read more
bottom, and took out all the bolts securing the clutch. Had to use a hammer to tap the shaft out from inside the drum. Then the clutch dropped out the bottom and I was able to remove the drum. Installation went smooth. Just remember the order you took stuff off and the position of the parts. They need to go on the same or the electrical connectors won't reach.
Read less
Was this helpful?
Thank you for voting!
The lights were on inside however the the water/ice dispenser did not work and the fridge and freezer side was not cooling
5 of 7 people
found this instruction helpful.
-
Rickey from DUMAS, AR
- Really Easy
- 30 - 60 mins
-
Socket set
Simply take off the back panel. Remove the old run capacitor which is attached to the compressor by a white part. It pulls right off. You will have to unplug two wires. I took a pic to ensure I plugged the wires back up the correct way. Then I attached the new capacitor to the white part and put on the sleeve that was included, plugge
... Read more
d it back into the compressor and zip tied the excess part of the sleeve. Once done plug fridge back up (always unplug electric devices when doing maintenance) to check before replacing back panel. It may take a few minutes before it kicks on.
Read less
Was this helpful?
Thank you for voting!
Pulsator stripped out
5 of 7 people
found this instruction helpful.
-
Anthony from FT WORTH, TX
- Really Easy
- 15 - 30 mins
-
Screw drivers, Socket set
The teeth in the pulsator assembly where stripped out on the original plate.
Ordered the replacement and it was 1 screw to undo and pop in the new assembly. Super easy repair
Ordered the replacement and it was 1 screw to undo and pop in the new assembly. Super easy repair
Was this helpful?
Thank you for voting!
Bad defrost timer
5 of 7 people
found this instruction helpful.
-
Bruce from Silver Spring, MD
- Really Easy
- 15 - 30 mins
-
Screw drivers
Parts Select made this an effortless process. From finding the part, ordering, to the online diagrams.
I'll be back...
I'll be back...
Was this helpful?
Thank you for voting!
freezer cold but refrigerator warm, would not cycle the defrost on freezer
4 of 4 people
found this instruction helpful.
-
MATT from OAKLAND, MI
- Really Easy
- Less than 15 mins
-
Screw drivers
two screws and a connector were removed to replace the timer.
Timer was located on the top front of fridge
Timer was located on the top front of fridge
Was this helpful?
Thank you for voting!
Smelled burning plastic
4 of 5 people
found this instruction helpful.
-
JOHN from PERKINSTON, MS
- Really Easy
- Less than 15 mins
-
Screw drivers
I removed the cardboard cover from the back of the fridge. I was not sure where to begin then the compressor kicked on and a flame came from the bottom of relay that mounts to compressor, so i unplugged fridge and let cool .I removed part that burned and looked on this site to identify what it is. The part has been updated to a new design
... Read more
which is now a white plastic. I also replaced run capacitor .Put the new parts on and it was back to working .The sleeve that comes with the new run capacitor didn't fit under the lock wire clip so i left off.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Old timer quit working.
7 of 14 people
found this instruction helpful.
-
John from Mesa, AZ
- Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
Installed the new timer.
Was this helpful?
Thank you for voting!
Low water flow into washer
4 of 5 people
found this instruction helpful.
-
Alexander from SALISBURY MLS, NY
- Really Easy
- 30 - 60 mins
-
Screw drivers
Replaced valve body, very easy to fix as per the video, runs normal.
Was this helpful?
Thank you for voting!
Water leaking into drum
4 of 5 people
found this instruction helpful.
-
Richard from RED LION, PA
- Really Easy
- 30 - 60 mins
-
Pliers, Screw drivers
Figured out how to remove the top door and the top panel that covered the solenoid bank. That was the hardest part. Swapping out the solenoid bank and the connector was easy. No more water leaking.
Other Parts Used:
Was this helpful?
Thank you for voting!
The old water assembly valve split on the bottom and started leaking.
4 of 6 people
found this instruction helpful.
-
Jerry from CARYVILLE, TN
- Very Easy
- 15 - 30 mins
-
Pliers, Screw drivers
After unplugging the washer I cut the water off. I took the water hoses off, then the back top panel using a phillips head screw driver. I then used a pair of pliers to take off the two hoses and clamps. I unplugged the electric connection on each solenoid, took out 5 screws replaced the part and did everything in reverse order. Problem s
... Read more
olved. Thanks for the fast service on my order.
Read less
Was this helpful?
Thank you for voting!
Loud motor noise emanating from inside the refrigerator (not the compressor or external fan).
3 of 3 people
found this instruction helpful.
-
Chong from NEW YORK, NY
- Easy
- Less than 15 mins
-
Screw drivers
My GE GDS18SBPBLSS is now 21 years old (they do not make them like they used to) so I took extra time to not break any of the brittle old plastics. For this replacement you will only need a Phillips head screwdriver.
Parts list:
2 x PS284959 Fan Motor Grommet
1 x PS2359960 Evaporator Fan Motor Assembly
• Th ... Read more e first thing you want to do is to unplug the unit refrigerator to prevent any shorts or the fan from starting while you are handling it.
• The evaporator motor is in the refrigerator section, so leave the freezer door shut to preserve the temperature.
• Open the refrigerator door as much as possible and take out the two vegetable/fruit drawers. If your door is right next to a wall and you cannot open it more than 90 degrees, take the drawer furthest from the door hinge first. Then take out the remaining drawer and gently shimmy the center plastic rail guide to allow you to take it out diagonally.
• The front lip of the floor of the refrigerator is clipped in, so pull the plastic trim forward to remove it. If it does not move, lift the center of the plastic trim piece in front of the screw a bit to convince it loose, but it prying it upwards is not advisable because the ends are under the side walls.
• Once the trim piece is removed, remove the Phillips head screw.
• Pull the plastic floor of the refrigerator towards the front and then up to remove it.
• A large foam block secured down with tape needs to be removed next. Once the tape is loosened, lift the foam out carefully with vapor barrier attached under it. Watch for the two foam pieces at the back wall on each side. If they fall off and drop, find them in the freezer later.
• The fan assembly and bracket will be in view, and my suggestion is to take a photo. This way, you know how it should look when it comes time to reassemble everything.
• To the left rear is a small foam block that is taped down. Removing that will reveal the connector clip for the fan motor’s power line that you squeeze the sides to disconnect. Pull the motor wire out of the foam guide.
• Lift the motor bracket assembly out – it is not attached to anything and sits on the foam block.
• Carefully pull the fan blade off by pulling it straight along the motor shaft.
• Undo the rear motor bracket by unscrewing the two Phillips head screws – the right rear motor bracket screw holds the wire guide in. When undone, take the guide off the wire.
• Once the rear bracket is removed, discard the two motor grommets and the motor.
• Put in the new motor with the new motor grommets into the bracket and screw in the left rear screw.
• Clip on the wire guide on to the new motor wiring and then finish mounting the motor with the right rear screw with the wire guide in place.
• Clean off the fan blade thoroughly before pressing into the shaft. Once on, spin the fan to see if it rotates smoothly and easily. Note: Avoid pressing the fan blade too far down as you do not want it to contact the grommet.
• Place the assembly back into the foam block – use the photo from before as a guide if needed.
• Route the motor cable through the foam groove and clip it into the power connector.
• Plug the refrigerator back in to see if the fan spins and to see that there are no issues. If there are no problems, unplug the unit again and continue the reassembly.
• Place the small foam block back into the rear left to cover the connector area.
• While making sure the vapor barrier is positioned correctly above the coils, put the foam block back into place.
• Clean the plastic floor of the refrigerator and then slide it into place, making sure the back and side are flush. Use the screw hole to align the floor properly and then screw the Phillips head screw back in.
• Clean the front trim piece and then slide it back into place.
• Put the drawers back in.
• Plug the refrigerator back in and leave the door closed for a while so the unit cools the internal temperature back down.
Parts list:
2 x PS284959 Fan Motor Grommet
1 x PS2359960 Evaporator Fan Motor Assembly
• Th ... Read more e first thing you want to do is to unplug the unit refrigerator to prevent any shorts or the fan from starting while you are handling it.
• The evaporator motor is in the refrigerator section, so leave the freezer door shut to preserve the temperature.
• Open the refrigerator door as much as possible and take out the two vegetable/fruit drawers. If your door is right next to a wall and you cannot open it more than 90 degrees, take the drawer furthest from the door hinge first. Then take out the remaining drawer and gently shimmy the center plastic rail guide to allow you to take it out diagonally.
• The front lip of the floor of the refrigerator is clipped in, so pull the plastic trim forward to remove it. If it does not move, lift the center of the plastic trim piece in front of the screw a bit to convince it loose, but it prying it upwards is not advisable because the ends are under the side walls.
• Once the trim piece is removed, remove the Phillips head screw.
• Pull the plastic floor of the refrigerator towards the front and then up to remove it.
• A large foam block secured down with tape needs to be removed next. Once the tape is loosened, lift the foam out carefully with vapor barrier attached under it. Watch for the two foam pieces at the back wall on each side. If they fall off and drop, find them in the freezer later.
• The fan assembly and bracket will be in view, and my suggestion is to take a photo. This way, you know how it should look when it comes time to reassemble everything.
• To the left rear is a small foam block that is taped down. Removing that will reveal the connector clip for the fan motor’s power line that you squeeze the sides to disconnect. Pull the motor wire out of the foam guide.
• Lift the motor bracket assembly out – it is not attached to anything and sits on the foam block.
• Carefully pull the fan blade off by pulling it straight along the motor shaft.
• Undo the rear motor bracket by unscrewing the two Phillips head screws – the right rear motor bracket screw holds the wire guide in. When undone, take the guide off the wire.
• Once the rear bracket is removed, discard the two motor grommets and the motor.
• Put in the new motor with the new motor grommets into the bracket and screw in the left rear screw.
• Clip on the wire guide on to the new motor wiring and then finish mounting the motor with the right rear screw with the wire guide in place.
• Clean off the fan blade thoroughly before pressing into the shaft. Once on, spin the fan to see if it rotates smoothly and easily. Note: Avoid pressing the fan blade too far down as you do not want it to contact the grommet.
• Place the assembly back into the foam block – use the photo from before as a guide if needed.
• Route the motor cable through the foam groove and clip it into the power connector.
• Plug the refrigerator back in to see if the fan spins and to see that there are no issues. If there are no problems, unplug the unit again and continue the reassembly.
• Place the small foam block back into the rear left to cover the connector area.
• While making sure the vapor barrier is positioned correctly above the coils, put the foam block back into place.
• Clean the plastic floor of the refrigerator and then slide it into place, making sure the back and side are flush. Use the screw hole to align the floor properly and then screw the Phillips head screw back in.
• Clean the front trim piece and then slide it back into place.
• Put the drawers back in.
• Plug the refrigerator back in and leave the door closed for a while so the unit cools the internal temperature back down.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
I had no problems
3 of 4 people
found this instruction helpful.
-
Sharron from RICHMOND, TX
- Really Easy
- 30 - 60 mins
-
Socket set, Wrench set
I can’t really say it was easy and I just did it
Was this helpful?
Thank you for voting!
Washer was noisy, made noise when agitating and spinning.
5 of 11 people
found this instruction helpful.
-
Paul from NANTICOKE, PA
- Really Easy
- 1- 2 hours
-
Socket set, Wrench (Adjustable)
I had a hard time removing the agitator, had to get thin prybar to get a hold of washplate. After I removed washplate, I found that the shaft that the washplate attaches to was actually worn out. What used to be a spline was smooth. So I ordered a new clutch assembly. There are a lot of bolts that hold the clutch assembly on to the
... Read more
basket. There are a lot of videos on Utube that will walk you through step by step. The only problem I encountered with this was removing the nut that holds the basket to the tub. One video said it was reverse thread, which it wasn’t. You can check the thread on new clutch assembly to see which way is correct. After I put back together. Works like new.
Read less
Was this helpful?
Thank you for voting!
washer making noise when washing. rinse and spin was normal.
2 of 2 people
found this instruction helpful.
-
David from BOTHELL, WA
- A Bit Difficult
- 1- 2 hours
-
Screw drivers, Socket set, Wrench (Adjustable)
Everthing went to plan except the wet side of the parts removal was difficult. used puller to remove the wash plate and got it to release. But the plastic part of the wash plate released and left the aluminum part still on the coupling. Corrision was the problem, and I had to again use a puller to remove this part of the wash plate. So it
... Read more
wasn't a matter of just lifting the wash plate off by hand. The rest of the replacement was fine.
Read less
Was this helpful?
Thank you for voting!