3146 - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Twice I ordered the oven light bulb & each time the light bulb was defected
18 of 38 people
found this instruction helpful.
-
Barbara from BELLEVUE, WA
- Very Difficult
- Less than 15 mins
I had to call for a appointment for repair with GE Appliance because I thought then it . .was something electrical. The technician came out & checked everything out, turned out it was not electrical, The technician went out to his truck got a light bulb from his truck, put it in & it worked. It cost me $121.00 for trip charge from GE appl
... Read more
iance for a light bulb that worked, your light bulbs were defective twice. Very disappointed with your products, cost me alot of money for a good light bulb thru GE appliance
Read less
Was this helpful?
Thank you for voting!
Ice in freezer running down sides
8 of 9 people
found this instruction helpful.
-
P. Michael from Tustin, CA
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
This is a built-in unit. Remove the external bezel at the top of the unit. Reach through the unit and unplug the frig. On the compressor unit, you'll see a vertical metal panel. Remove the metal panel and the timer is right behind it. Remove one wire at a time and switch it to the new timer. Remove timer and replace with new one.
... Read more />
Just an added comment, GE Service wanted to put an "ice kit" into my unit. The full repairs would have cost $1,000. While I described how to replace the defrost timer, the problem was the tray heater. But that's another story.
... Read more />
Just an added comment, GE Service wanted to put an "ice kit" into my unit. The full repairs would have cost $1,000. While I described how to replace the defrost timer, the problem was the tray heater. But that's another story.
Read less
Was this helpful?
Thank you for voting!
Washer was slowing filling with water when turned off.
9 of 12 people
found this instruction helpful.
-
Michael from La Honda, CA
- Very Easy
- 30 - 60 mins
-
Pliers, Screw drivers
The problem was the valve suppling water to the bleach dispenser was not closing completely. This also caused some water leaking towards
the front of the washer. Replacing the entire valve assembly was very
easy. Unplug the washer, turn off the water, remove the 2 screws that attach the control panel, disconnect the water supp ... Read more lies, unplug the 5 solenoids, remove the hose clamps from the 2 hoses, remove the 3
screws that attach the valve assembly and remove it. Reassemble in reverse order, I did find that applying some water based personal lubricant to the 3 high pressure seals made assembly much easier.
the front of the washer. Replacing the entire valve assembly was very
easy. Unplug the washer, turn off the water, remove the 2 screws that attach the control panel, disconnect the water supp ... Read more lies, unplug the 5 solenoids, remove the hose clamps from the 2 hoses, remove the 3
screws that attach the valve assembly and remove it. Reassemble in reverse order, I did find that applying some water based personal lubricant to the 3 high pressure seals made assembly much easier.
Read less
Was this helpful?
Thank you for voting!
defrost system kept freezing up
8 of 10 people
found this instruction helpful.
-
Robert from Williamstown, NY
- Easy
- 15 - 30 mins
-
Screw drivers
took out 4 screws - lowered timer cover - replaced timer- put it back together
Was this helpful?
Thank you for voting!
Freezer not getting cold enough to freeze ice cream
8 of 10 people
found this instruction helpful.
-
Gary from ROSETO, PA
- A Bit Difficult
- 30 - 60 mins
-
Screw drivers
I took the advice off of your website about the only thing that will fix
the problem is change the run capacitor. I felt assured that I would
have a working refrigerator freezer after making this change. I was
pretty disheartened when it didn`t solve anything. I was not going to
take the new part back out after the sma ... Read more ll challenge of putting it in.
The next day I found out how to test the old capacitor and it was still
good. I will just have to eat the $49. I did learn not to take advice from
a website even if it seems like a sure thing
the problem is change the run capacitor. I felt assured that I would
have a working refrigerator freezer after making this change. I was
pretty disheartened when it didn`t solve anything. I was not going to
take the new part back out after the sma ... Read more ll challenge of putting it in.
The next day I found out how to test the old capacitor and it was still
good. I will just have to eat the $49. I did learn not to take advice from
a website even if it seems like a sure thing
Read less
Was this helpful?
Thank you for voting!
Refridgerator wouldn't cycle into defrost mode without doing it manually.
9 of 14 people
found this instruction helpful.
-
Ben from Warrior, AL
- Easy
- 15 - 30 mins
-
Screw drivers, Socket set
I removed the shield over the timer and the part that supported the timer. Just unpluged it and pluged in new timer and put back shield. I had already replaced the defrost heaters which had totally burned up. I also replaced the thermostat while I was making the repairs although the old one was still o.k. All the information that I needed
... Read more
to make the repairs I obtained through your website. After looking at several websites to compare prices-etc, I found yours to be the best overall. Thanks-a-million your website is worth it's weight in Cold Food !
Read less
Was this helpful?
Thank you for voting!
Frige evaporator fan became noisy then quit working & frige compartment became warm
6 of 6 people
found this instruction helpful.
-
Scott from Bonney Lake, WA
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Came home one evening and found the refer compartment evaporator fan making a noisy/grinding noise. While waiting for the part to arrive the motor finally quit working and the frige lost its ability to cool, but the freezer still worked fine. This is the fan that is inside the frige between the refer & freezer compartments - NOT the fan m
... Read more
otor that is located in the bottom/rear next to the compressor. This grinding noise sounded like it was coming from inside the frige and could be easily heard under the vegetable trays and above the freezer compartment. To access this motor you need to go after it from inside the bottom of the frige compartment - there's NO need to remove the refer door. Pull the vegetable trays and remove the small phillips head screw located down in the lower air flow groove toward the front of the refer. Next, pry up & out the front white trim piece that runs the width of the frige. Once that piece is removed you can lift & slide back the whole lower frige trim/tray. Now lift out the large foam block compartment and you'll have complete access to the evaporator fan motor and the evap coils. Simply pull the fan motor assy out, still attached to the triangular bracket and disconnect the electrical pigtail. Next, pull the fan blade straight off the front hub, split & disassemble the motor bracket, & replace both fan motor grommets. Reverse the steps to reassemble the fan motor to the bracket and reinstall back in the bottom of the frige and plug in the electrical pigtail - the fan should (quietly) fire off instantly and begin the cooilng process. Reinstall the foam block, lower frige tray, front trim piece, reattach the phillips screw, close the door, and give it some time - it took our frige overnight to completely cool down. This is not a tough job, I spent more time figuring out how to access the motor then the actuall replacement. Hope these steps help to speed up your repair! And remeber Red Sox 4 Life!
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
refrigerator wasn't cooling but the freezer was working properly
6 of 6 people
found this instruction helpful.
-
Don from BELLVILLE, TX
- Very Easy
- 15 - 30 mins
-
Nutdriver
From instructions found on the site I was directed to the defrost timer part being bad. And from the information others posted that have had the same problem I was able to replace that part by removing the bottom grill just below the door and on the left side was the part. Removing one screw to remove the bracket from the frame and then
... Read more
another screw to remove the part from the bracket. I found it easier to remove the part from the bracket before I pulled the part out so I would have more room to unplug the connector. Just reverse the steps to replace the new part. It took about a day or so for the refrigerator to get to the proper temp.
Read less
Was this helpful?
Thank you for voting!
The bolt in pulsator kept coming out during the wash
6 of 6 people
found this instruction helpful.
-
Deresa from BOLINGBROOK, IL
- Really Easy
- Less than 15 mins
-
Socket set
I found the pulsator just spun freely, I determined the hole on underside should ribbed to align with the ribbed shaft. But it was wore away. I purchased the new part and replacement was simple. It slide right on and I replaced the bolt. Pulsator works great, washing again.
Was this helpful?
Thank you for voting!
Direct drive shaft broke right under the agitator plate.
6 of 7 people
found this instruction helpful.
-
EDWIN from FELTON, DE
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers, Socket set
Removed the inner tub laid the washer on its side with a blanket under it and Removed the assembly then the shaft assembly.
Installed the new assembly and re assembled the rest of the washer (top and bottom) and plugged it in. Works great. TIP: you will need a big socket set for the tub retaining nut.
Installed the new assembly and re assembled the rest of the washer (top and bottom) and plugged it in. Works great. TIP: you will need a big socket set for the tub retaining nut.
Was this helpful?
Thank you for voting!
Top loading washing machine displayed "tE" error
6 of 7 people
found this instruction helpful.
-
Angelica from HOUSTON, TX
- Easy
- 30 - 60 mins
-
Pliers, Wrench (Adjustable)
Disconnect machine from power source. Then, disconnect any tubes from the back side (make sure you close any water valves before doing so). Then, lay the machine on its back to access the bottom of the machine. Then, locate the thermistor and replace it with the new one (the thermistor will have two screws holding it in place, simply remo
... Read more
ve the screws and replace the thermistor, then screw it back in). After the new part is installed, stand the machine back up and make sure to connect any tubing to its proper place. Done.
Read less
Was this helpful?
Thank you for voting!
Noisy refrigerator
6 of 8 people
found this instruction helpful.
-
Eric from NEW YORK, NY
- A Bit Difficult
- 1- 2 hours
-
Nutdriver, Screw drivers
I visually inspected the compressor and narrowed down the source of the noise to the freezer area. Then I removed the doors and the screws securing the divider panel. Next I removed the bottom panel of the freezer, the styrofoam insullation panel and the evaporator motor. The motor is mounted between two grommets. I replaced the gromme
... Read more
t facing the fan blades. The aluminum reflector below the styrofoam insulation panel had also come loose. I reattached it and reassembled the refrigerator in reverse order. The noise is gone!
Read less
Was this helpful?
Thank you for voting!
Refrigerator to warm
5 of 5 people
found this instruction helpful.
-
Lloyd from PITTSBURG, CA
- Easy
- 15 - 30 mins
-
Screw drivers
Instructions say run capacitor is by motor, but on this frige its in the refrigerator compartment. The capacitors looks different, one square and the other long
Was this helpful?
Thank you for voting!
Agitator was free spinning
8 of 14 people
found this instruction helpful.
-
Joel from JASPER, MO
- Very Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
Removed the center cover cap carefully on top of the agitator with a small screw driver. There are 3 (on mine) little slots around the edge of the bottom of the cap where it meets the agitator. Insert the small flat blade screwdriver and gently twist at each one till the cap pops loose and comes off.
There was a 10MM bolt under ... Read more the cap on mine that you need to remove. I used an cordless impact driver but you could use a socket wrench as well. Remove the bolt and the agitator comes off. May take a little wiggling or it may come right off.
The teeth on the agitator were wore all the way down and gone on mine so it came off easy and this was the issue I had why it was spinning freely. I took the small flat blade screwdriver and used the edge and corner of the blade to clean the teeth on the shaft where the agitator attaches and wiped it down before installing the new part as there was quite a bit of metal shavings from the damaged part.
I just reversed the order of removal to install the new part. Took about 15 min. I ran a rinse and spin cycle to remove any additional metal shavings and to check to see if it all worked properly. THATS IT! TOO EASY!
There was a 10MM bolt under ... Read more the cap on mine that you need to remove. I used an cordless impact driver but you could use a socket wrench as well. Remove the bolt and the agitator comes off. May take a little wiggling or it may come right off.
The teeth on the agitator were wore all the way down and gone on mine so it came off easy and this was the issue I had why it was spinning freely. I took the small flat blade screwdriver and used the edge and corner of the blade to clean the teeth on the shaft where the agitator attaches and wiped it down before installing the new part as there was quite a bit of metal shavings from the damaged part.
I just reversed the order of removal to install the new part. Took about 15 min. I ran a rinse and spin cycle to remove any additional metal shavings and to check to see if it all worked properly. THATS IT! TOO EASY!
Read less
Was this helpful?
Thank you for voting!
Washer Hot water valve did not shut off ever
5 of 5 people
found this instruction helpful.
-
Scott from SANTA CLARITA, CA
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
After getting the model info from the back of the washer control panel, I searched Partselect for the water valve part. Easy process, It was here in 2 days. Unplug the machine, I took 2 screws out of the back of the control console and tipped it forward to reveal the valve assy. Turn off the water at the wall and disconnect the hot and co
... Read more
ld lines from the washer . I removed the 3 screws holding the valve assy to the deck and with pliers disconnected the 2 clamped rubber lines and then with just finger pressure wiggled the valve from the remaining pipe connections. I swapped the 5 wire connectors to the new valve and wiggled it back into place. Clamped the 2 rubber lines again. and then connected the water inlet hoses to the new valve. Closed it up and called the laundry lady ( sorry honey) 30 minutes to Household harmony again!!
Read less
Was this helpful?
Thank you for voting!