My Orders
Haier Washer Parts
GET YOUR OFFICIAL Haier PARTS TO ENSURE VICTORY
Shop By Part Type
View MorePopular Haier Washer Parts
Repeated clicking, an insecure latch, or interrupted wash cycles may indicate a worn door lock assembly. The lock secures the door during washing and spinning while helping prevent operation when the door is open. First check the door alignment, strike, gasket, connectors, and nearby wiring. Match the replacement to the washers full model number because similar locks may use different plugs or mounting points. Disconnect electrical power before opening the cabinet, and wait for the drum to stop completely before handling the door. Do not operate the appliance with its safety lock defeated.
Repeated clicking, an insecure latch, or interrupted wash cycles may indicate a worn door lock assembly. The lock secures the door during washing and spinning while helping prevent operation when the door is open. First check the door alignment, strike, gasket, connectors, and nearby wiring. Match the replacement to the washers full model number because similar locks may use different plugs or mounting points. Disconnect electrical power before opening the cabinet, and wait for the drum to stop completely before handling the door. Do not operate the appliance with its safety lock defeated.
Water left in the washer or clothes that remain very wet may point to a weak drain pump. A damaged impeller can also cause humming or drain error codes. Before replacing the pump, clean the filter and check the drain path for clogs. Match the new pump to the full appliance model and parts diagram. Unplug the washer, shut off the water, and prepare for spills. Reconnect each hose and wire correctly, tighten every clamp, and watch for leaks during a short test cycle.
Water left in the washer or clothes that remain very wet may point to a weak drain pump. A damaged impeller can also cause humming or drain error codes. Before replacing the pump, clean the filter and check the drain path for clogs. Match the new pump to the full appliance model and parts diagram. Unplug the washer, shut off the water, and prepare for spills. Reconnect each hose and wire correctly, tighten every clamp, and watch for leaks during a short test cycle.
MAKE THIS REPAIR A GUARANTEED WIN
OVER 2 MILLION PARTS TO ENSURE VICTORY
A washer that stops mid-cycle or leaves water in the drum may have a blocked or damaged drain pump. The pump uses an internal impeller to push wastewater out through the drain system. First check the drain hose, filter, and pump inlet for kinks or trapped debris that can mimic pump failure. Match the replacement to the appliances full model number and electrical connections. Disconnect power and water before opening the cabinet, prepare for residual water, and keep wiring dry. After installation, run a short cycle and inspect every connection for leaks.
A washer that stops mid-cycle or leaves water in the drum may have a blocked or damaged drain pump. The pump uses an internal impeller to push wastewater out through the drain system. First check the drain hose, filter, and pump inlet for kinks or trapped debris that can mimic pump failure. Match the replacement to the appliances full model number and electrical connections. Disconnect power and water before opening the cabinet, prepare for residual water, and keep wiring dry. After installation, run a short cycle and inspect every connection for leaks.
Installation Instructions
ILANA from NEW YORK, NY
The water stopped draining.
I emptied all the water with a cup and laid the washer down on its back on the bathroom floor, ( it is a portable), with a few small pots and rags handy to collect water, just in case.
I inspected the placement of the broken drain pump, I took photographs of all the wires placements and screws. I removed the broken drain pump pho ... Read more tographing each step, then attached the new drain pump following each step in reverse and attached the 2 colored wires to the remains of the colored wires attached to the washer. I used electric tape to isolate and cover completely the exposed wires parts i joined. I then screwed everything back in place. I put the washer upright, connected the electrical cord and did a test. It is working great, and the water is draining well! It took me over 30 minutes, as the space under the machine, where the drain pump lodges, is quite tight and I needed a flash light.
I inspected the placement of the broken drain pump, I took photographs of all the wires placements and screws. I removed the broken drain pump pho ... Read more tographing each step, then attached the new drain pump following each step in reverse and attached the 2 colored wires to the remains of the colored wires attached to the washer. I used electric tape to isolate and cover completely the exposed wires parts i joined. I then screwed everything back in place. I put the washer upright, connected the electrical cord and did a test. It is working great, and the water is draining well! It took me over 30 minutes, as the space under the machine, where the drain pump lodges, is quite tight and I needed a flash light.
Read less
This hot water valve controls the flow of hot water into the appliance, opening and closing based on operational needs. It is commonly replaced when water flow becomes inconsistent, restricted, or leaks occur.
This hot water valve controls the flow of hot water into the appliance, opening and closing based on operational needs. It is commonly replaced when water flow becomes inconsistent, restricted, or leaks occur.
Filling problems often begin with a blocked screen, bent hose, closed faucet, or worn inlet valve. The cold-water valve controls when water enters the appliance and stops the flow when it is no longer needed. Check the simpler causes before ordering a replacement, then confirm compatibility using the full model number. Disconnect electrical power and close the water supply before service. Tighten the connections carefully, restore the water slowly, and inspect the repair for leaks before running a complete cycle.
Filling problems often begin with a blocked screen, bent hose, closed faucet, or worn inlet valve. The cold-water valve controls when water enters the appliance and stops the flow when it is no longer needed. Check the simpler causes before ordering a replacement, then confirm compatibility using the full model number. Disconnect electrical power and close the water supply before service. Tighten the connections carefully, restore the water slowly, and inspect the repair for leaks before running a complete cycle.
Installation Instructions
Annette from SEATTLE, WA
Replace inlet valve
Easy. Just need to remove top and 1 panel to access. Not too tight of a workspace.