Models > HLP28E

HLP28E Haier Washer - Overview

Sections of the HLP28E

[Viewing 1 of 1]
Keep searches simple, eg. "belt" or "pump".
WASHING MACHINE DRAIN PUMP – Part Number: WH23X27419
WASHING MACHINE DRAIN PUMP
★★★★★
★★★★★
(2)
PartSelect #: PS12343437
Manufacturer #: WH23X27419
$57.65
  In Stock
WASHING MACHINE WATER INLET VALVE – Part Number: WH13X26636
WASHING MACHINE WATER INLET VALVE
★★★★★
★★★★★
(1)
PartSelect #: PS12343364
Manufacturer #: WH13X26636
$31.73
  In Stock
BELT - LOCKING – Part Number: WD-0350-14
BELT - LOCKING
PartSelect #: PS4126108
Manufacturer #: WD-0350-14
  No Longer Available
LINT FILTER – Part Number: WH01X27265
LINT FILTER
PartSelect #: PS12343265
Manufacturer #: WH01X27265
$6.68
  In Stock
BELT – Part Number: WD-0350-46
BELT
PartSelect #: PS4126140
Manufacturer #: WD-0350-46
  No Longer Available
CLAMPDRAIN HOSE – Part Number: WD-1640-48
CLAMPDRAIN HOSE
PartSelect #: PS4126699
Manufacturer #: WD-1640-48
  No Longer Available
WASHING MACHINE ACTUATOR MOTOR BRAKE – Part Number: WH20X27368
WASHING MACHINE ACTUATOR MOTOR BRAKE
PartSelect #: PS12343434
Manufacturer #: WH20X27368
$45.23
  In Stock
DRAIN PIPE – Part Number: WH41X27715
DRAIN PIPE
PartSelect #: PS12343464
Manufacturer #: WH41X27715
$19.03
  In Stock
WASHING MACHINE CONTROL PANEL SEAT – Part Number: WH44X26195
WASHING MACHINE CONTROL PANEL SEAT
PartSelect #: PS12343489
Manufacturer #: WH44X26195
$51.99
  In Stock
BELT PROTECTOR BOLT – Part Number: WH02X26924
BELT PROTECTOR BOLT
PartSelect #: PS12343303
Manufacturer #: WH02X26924
$6.68
  In Stock

Questions And Answers for HLP28E

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

Common Symptoms of the HLP28E

[Viewing 1 of 1]
Will not drain
Fixed by
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
The water stopped draining.
I emptied all the water with a cup and laid the washer down on its back on the bathroom floor, ( it is a portable), with a few small pots and rags handy to collect water, just in case.
I inspected the placement of the broken drain pump, I took photographs of all the wires placements and screws. I removed the broken drain pump photographing each step, then attached the new drain pump following each step in reverse and attached the 2 colored wires to the remains of the colored wires attached to the washer. I used electric tape to isolate and cover completely the exposed wires parts i joined. I then screwed everything back in place. I put the washer upright, connected the electrical cord and did a test. It is working great, and the water is draining well! It took me over 30 minutes, as the space under the machine, where the drain pump lodges, is quite tight and I needed a flash light.
Parts Used:
WASHING MACHINE DRAIN PUMP
  • ILANA from NEW YORK, NY
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers
6 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Washer wouldn't drain.
Lifted up the washer from the bottom. Accessed the pump, unscrewed the motor and pulled off the rubber hose attached to the pump using a Phillips screwdriver and a wrench.
Reattached the hose and the mounting screws. Worked just fine.
Parts Used:
WASHING MACHINE DRAIN PUMP
  • GABRIEL from GANADO, AZ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Wrench (Adjustable)
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Replace inlet valve
Easy. Just need to remove top and 1 panel to access. Not too tight of a workspace.
Parts Used:
WASHING MACHINE WATER INLET VALVE
  • Annette from SEATTLE, WA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!