Models > GWT480BW

GWT480BW Haier Washer - Overview

Sections of the GWT480BW

[Viewing 1 of 1]
Keep searches simple, eg. "belt" or "pump".
WASHING MACHINE DRAIN PUMP – Part Number: WH23X27419
WASHING MACHINE DRAIN PUMP
★★★★★
★★★★★
(2)
PartSelect #: PS12343437
Manufacturer #: WH23X27419
$57.65
  In Stock
WASHING MACHINE DRIVE BELT – Part Number: WH07X27361
WASHING MACHINE DRIVE BELT
PartSelect #: PS12343333
Manufacturer #: WH07X27361
$73.88
  In Stock
BELT - LOCKING – Part Number: WD-0350-14
BELT - LOCKING
PartSelect #: PS4126108
Manufacturer #: WD-0350-14
  No Longer Available
WASHING MACHINE SHOCK DAMPENER – Part Number: WH16X27359
WASHING MACHINE SHOCK DAMPENER
PartSelect #: PS12343392
Manufacturer #: WH16X27359
$21.34
  In Stock
WASHING MACHINE DRAIN HOSE – Part Number: WH41X27396
WASHING MACHINE DRAIN HOSE
PartSelect #: PS12343460
Manufacturer #: WH41X27396
$13.90
  In Stock
WASHING MACHINE DOOR SWITCH – Part Number: WH01X27376
WASHING MACHINE DOOR SWITCH
PartSelect #: PS12343272
Manufacturer #: WH01X27376
$16.69
  In Stock
WASHING MACHINE SHOCK DAMPENER – Part Number: WH16X27358
WASHING MACHINE SHOCK DAMPENER
PartSelect #: PS12343391
Manufacturer #: WH16X27358
$20.53
  In Stock
WASHING MACHINE ACTUATOR MOTOR BRAKE – Part Number: WH20X27368
WASHING MACHINE ACTUATOR MOTOR BRAKE
PartSelect #: PS12343434
Manufacturer #: WH20X27368
$45.23
  In Stock
INLET VALVE – Part Number: WH01X27871
INLET VALVE
PartSelect #: PS12582943
Manufacturer #: WH01X27871
$47.36
  In Stock
WASHING MACHINE ELECTROMAGNET – Part Number: WH01X27384
WASHING MACHINE ELECTROMAGNET
PartSelect #: PS12343273
Manufacturer #: WH01X27384
$14.39
  Special Order

Questions And Answers for GWT480BW

Be the first to ask our experts a question about this model!

Common Symptoms of the GWT480BW

[Viewing 1 of 1]
Will not drain
Fixed by
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
The water stopped draining.
I emptied all the water with a cup and laid the washer down on its back on the bathroom floor, ( it is a portable), with a few small pots and rags handy to collect water, just in case.
I inspected the placement of the broken drain pump, I took photographs of all the wires placements and screws. I removed the broken drain pump photographing each step, then attached the new drain pump following each step in reverse and attached the 2 colored wires to the remains of the colored wires attached to the washer. I used electric tape to isolate and cover completely the exposed wires parts i joined. I then screwed everything back in place. I put the washer upright, connected the electrical cord and did a test. It is working great, and the water is draining well! It took me over 30 minutes, as the space under the machine, where the drain pump lodges, is quite tight and I needed a flash light.
Parts Used:
WASHING MACHINE DRAIN PUMP
  • ILANA from NEW YORK, NY
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers
6 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Washer wouldn't drain.
Lifted up the washer from the bottom. Accessed the pump, unscrewed the motor and pulled off the rubber hose attached to the pump using a Phillips screwdriver and a wrench.
Reattached the hose and the mounting screws. Worked just fine.
Parts Used:
WASHING MACHINE DRAIN PUMP
  • GABRIEL from GANADO, AZ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Wrench (Adjustable)
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Off balance tub made banging noise during spin.
Washer was making loud banging noise during spin cycle. I noticed that tub was off center within washer housing while turned off. Removed top and checked for springs used to hold tub centered in the housing. Found one spring loaded support rod (Dampin)that had a broken spring. Due to two different part numbers, PS4125965 and PS4125966 it required considerable time to order the correct part, no parts supplier was aware of the reason for two part numbers. I had to contact the engineering department of Haier to fine the correct item, one number is for the right side the other number for the left side of the washer tub. Part snaps in place in upper corner of the washer housing and in a slot at the lower edge of the tub. No tools required to install Dampin just a screwdriver to remove top of washer. Parts arrived two days after ordering, very good service.
Parts Used:
WASHING MACHINE SHOCK DAMPENER WASHING MACHINE SHOCK DAMPENER
  • Richard from Lewes, DE
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!