Ask our experts a question about this model and we'll get back to you as soon as possible!
We may have answered a similar question already! Search questions and answers left by others using simple keywords like "fit", "broken", "easy", or "quality" to find questions that match.
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Sort by:
Prev
1
Next
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Carlene - For model number GWT460AW
September 1, 2021
My machine wont spin and drain, I already change the belt and it make a whurring sound.
Hello Carlene, Thank you for the question. We suggest checking the Drain Pump. If the Pump is not operating it will not allow the tub to spin. We hope this helps!
Why doesnβt the cold water run into the washer at a normal speed?
Hello Teresa, thank you for the question. We would recommend checking the water inlet valve, part number PS12582943, to fix the issue. It controls the water flow into the washer. Glad to be of assistance!
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
The water stopped draining.
8 of 10 peoplefound this instruction helpful.
ILANA from NEW YORK, NY
A Bit Difficult
30 - 60 mins
Pliers, Screw drivers
I emptied all the water with a cup and laid the washer down on its back on the bathroom floor, ( it is a portable), with a few small pots and rags handy to collect water, just in case. I inspected the placement of the broken drain pump, I took photographs of all the wires placements and screws. I removed the broken drain pump pho
... Read moretographing each step, then attached the new drain pump following each step in reverse and attached the 2 colored wires to the remains of the colored wires attached to the washer. I used electric tape to isolate and cover completely the exposed wires parts i joined. I then screwed everything back in place. I put the washer upright, connected the electrical cord and did a test. It is working great, and the water is draining well! It took me over 30 minutes, as the space under the machine, where the drain pump lodges, is quite tight and I needed a flash light.
Read less
Was this helpful?
Thank you for voting!
Washer wouldn't drain.
4 of 8 peoplefound this instruction helpful.
GABRIEL from GANADO, AZ
Really Easy
30 - 60 mins
Wrench (Adjustable)
Lifted up the washer from the bottom. Accessed the pump, unscrewed the motor and pulled off the rubber hose attached to the pump using a Phillips screwdriver and a wrench. Reattached the hose and the mounting screws. Worked just fine.
Was this helpful?
Thank you for voting!
Off balance tub made banging noise during spin.
1 personfound this instruction helpful.
Richard from Lewes, DE
Easy
15 - 30 mins
Pliers, Screw drivers
Washer was making loud banging noise during spin cycle. I noticed that tub was off center within washer housing while turned off. Removed top and checked for springs used to hold tub centered in the housing. Found one spring loaded support rod (Dampin)that had a broken spring. Due to two different part numbers, PS4125965 and PS4125966 it
... Read morerequired considerable time to order the correct part, no parts supplier was aware of the reason for two part numbers. I had to contact the engineering department of Haier to fine the correct item, one number is for the right side the other number for the left side of the washer tub. Part snaps in place in upper corner of the washer housing and in a slot at the lower edge of the tub. No tools required to install Dampin just a screwdriver to remove top of washer. Parts arrived two days after ordering, very good service.