Gibson Range Switches

Gibson Appliance Parts
Shop By Part Type

Popular Gibson Range Switches

Your Price
$31.37
  In Stock
Infinite Burner Switch
★★★★★
★★★★★
(41)
PartSelect Number PS1145040
Manufacturer Part Number 316436001
The infinite burner switch controls the stove top eight-inch surface burner, which is the large surface element. If your surface element is not warming up, the element can be tested to determine whether or not it is defective. If your element is not defective, then it is more than likely that the infinite burner switch is the issue. Before you install the infinite burner switch you will need to unplug your range from the power supply, or shut off the home circuit breaker. The tools you will need to do this repair include a number one square head screwdriver and a pair of needle nose pliers.
Fixes these symptoms
  • Element will not heat
  • Oven is too hot
  • Oven not heating evenly
  • See more...
Installation Instructions
William from Burke, VA
Back Burner didn't function
We moved into our townhouse about 6 yrs ago. During the home inspection we checked the range and saw the Red light come on when we turned on each burner. After moving in we realized the large back burner did not work. The light came on but the element never got hot. I of course replaced the element but that did not work. Several years passed and we just ignored the issue. We just got by with 3 burners. Lately we realized how much easier it would be to have all four burners working. Knowing that we will be selling our townhome soon we figured we should either fix the problem or replace the range.

I didn't want to call a repair man because I didn't want to be charged a $150 to have him come out and they to pay extra for parts (and of course a 2nd visit). So I went to www.Partselect.com and typed in the model of my range. Found the diagrams for my range and saw that from the switch ran a pair of wires to a Universal Receptacle (aka Terminal Block Kit). I figured since the Red light turns on when I turn the switch on it has to be the Terminal Block.

I ordered the part from www.Partselect.com ($14.00 including shipping) and replaced the part. The burner still would not get hot. I decided to test the switch. I removed the Control Panel cover (which is secure by 2 screws just below the digital clock). Once the cover was off, I saw the Blue wires going from the switch to the Terminal Block. To test the switch, I disconnected the two Blue Wires from connectors H1 and H2 and temporarily connected them to H1 and H2 of another switch. Sure enough, when I turned the other switch the element got hot.

So I placed another order from www.Partselect.com for a replacement switch ($50 including shipping). When that part came, I flipped the electrical circuit going to the range. I then removed the Control Panel cover again. With the new switch in hand (holding it near the old switch still attached to the Control Panel, I used the pliers to pull out each wire from it's connector and place it to it's corresponding connector on the new switch. Once all the wires were connected to the new switch, I pulled the knob of the switch off then used a phillips screwdriver to remove the two screws holding the switch to the control panel. I replaced the old switch with the new one put the screws back in, replaced the knob. Turned the circuit back on and tested to make sure that the element got hot. When it did, then I replaced the Control Panel cover and enjoyed a nice dinner that was cooked in less time than we're accustomed to because of the new burner. So I spent a total of $64.00 to fix our range. Less than half the amount I would've spent if I called for a technican. And far less then buying a new range.

Partselect is a great resource for information. They have diagrams and schematics available to view and/or download. And when ordering it's a snap because there's an "Add to Cart" button next to each part it lists. So there's no confusion. I've already recommended Partselect.com to about 5 people. And will continue to do so!!
Read more...
Your Price
$37.19
  In Stock
Infinite Burner Switch - Small Element - 240V
★★★★★
★★★★★
(7)
PartSelect Number PS1145039
Manufacturer Part Number 316436000
This is a part for your range. This switch controls the stovetop surface burner. If you notice that your stove top is not turning on or is not adjusting to the corresponding desired heat, it is mostly likely due to the burner switch needing to be replaced. You will need a #1 square-head screwdriver and needle-nose pliers. Disconnect the power from the range. You will need to move the range out from the wall to remove the upper back panel to access to this part. This is an OEM genuine part.
Fixes these symptoms
Installation Instructions
Gerald from Paris, TN
Switch Was Making A Arcing Sound When Burner Was On
Removed the back cover of the range. Removed the knob from the front of the switch. Removed 2 screws holding switch to range. Removed wires one at a time and connected to proper poles on replacement switch and reinstalled new switch on range Read more...
Your Price
$25.25
  In Stock
Burner Switch Kit
★★★★★
★★★★★
(8)
PartSelect Number PS470145
Manufacturer Part Number 5303935086
This is a burner switch kit, also known as the surface element control switch repair kit, for ranges. This burner switch kit sends voltage to the surface element coil and it controls the stove top surface burner. If the following symptoms occur, installing the switch could be the solution to the problem: surface element not heating, overheating, or inconsistent heating. Usually, if the element is not defective, that is a sign there is an issue with the switch. The kit comes with several insert sizes, and includes screws as well. The tools needed for this project are a nut driver, pliers, and screwdrivers.
Fixes these symptoms
Installation Instructions
George from New Port Richey, FL
High heat reluctant to turn down.
Most of the job is simple fastener mechanics.
Use a nut driver or Phillips screwdriver. Remove rear panel.

Pull out control knob. If it is stuck, wrap a small rag around the back of it and pull the rag steadily.

Carefully match marked terminals on the replacement switch with those on original. Switch terminals may not be in the same location. Replace wires one for one, one at a time.

Carefully select the correct knob filler for the switch post. Several are supplied. Proceed with logic and measure the shaft length and the filler length and type to match.
Read more...
Your Price
$47.15
  In Stock
Infinite Burner Switch - 8" - 240V
★★★★★
★★★★★
(1)
PartSelect Number PS1529262
Manufacturer Part Number 318293811
This switch controls the stove top surface burner.
Fixes these symptoms
Installation Instructions
George from WYOMING, MI
Controller fails to hold a constant heating element tempature
The replacement of this part is simple enough, out with the old, in with the new. At issue here is the way the controller fails. The heating element goes to the highest temperature. The original controller on this Kenmore oven failed after about two years and the first replacement that I got from you lasted about a year and a half. The defective controllers seem to be working properly once the controller has been turned off and then restarted, but the frequency of failure increases with time until you hardly dare to step away from the oven. This controller should open on failyor, not close.

George Ritz
Read more...
Your Price
$55.02
  In Stock
Oven Door Light Switch
PartSelect Number PS1146808
Manufacturer Part Number 316445501
This oven door light switch signals the light to turn off when the oven door closes. If your light switch is defective or you smell a burning odor, make sure to check the switch and replace it. The tool needed for this replacement is a screwdriver. Locate the switch, usually from under the oven top. Remove the wires and pull the switch out. Refer to the diagram provided by the manufacturer for further instructions and guidance before installation. Make sure you remember to unplug the oven from the power source before starting this repair, and wear gloves for protection.
Installation Instructions
Vincent from Brunswick, GA
Oven light stayed on & smelled like electrical burning.
Wife was cooking our thanks giving turkey, when an oder of burning was noticed. I walked over to the oven and smelled the area of oven light, it was bad. I turned off and unpluged oven. Got a screw driver, unscrewed 4 screws then noticed the burned switch from under the oven top. removed 3 wires, covered w/ elec. tape, and pulled oven light switch out front. looked at part number and ordered online. We were able to cook our turkey and enjoyed our meal. Read more...
Your Price
$66.97
  In Stock
Spark Module - 120V
PartSelect Number PS468140
Manufacturer Part Number 5303912606
This part sends enough current to the igniter to create a spark to the bottom of the burner cap.
Fixes these symptoms
Installation Instructions
Jonathan from Arkport, NY
My burners would not light. There wasn't the tell tale "click, click, click" of the spark module.
First I had to slide the stove out of its cubby and then I removed the two screws holding on the shield. I next removed the wires going to the spark module. I removed the top screw and loosened the bottom one. Installed the new spark module in reverse order. Less than 15 minutes for whole repair. Still have problems with spark module not working if oven is on, but I think it is because there is no air circulation behind the stove. Read more...
Your Price
$48.37
  Special Order
SWITCH
★★★★★
★★★★★
(1)
PartSelect Number PS1529261
Manufacturer Part Number 318293810
Fixes these symptoms
Your Price
$48.33
  In Stock
Gas Spark Ignition Switch
PartSelect Number PS437415
Manufacturer Part Number 316035200
When the gas burner valve knob is depressed and turned, this part creates a spark that lights the gas and starts the burner
Fixes these symptoms
Installation Instructions
Donald from Middle Village, NY
Two top burners would not light, defective switch
Warning- we found a lot of bare wires in this stove, check your wires before replacing the bad switches. I lifted the top, disconnected the power, pulled off the knobs, unscrewed the switch for the back light, removed seven screws to finally get the front panel off. Once you have the front panel off, changing the swich takes less than a minute. The switches just slide off the gas valve stems. Instructions show how to line up the new D-shaped switch mechanism to match the D-shaped shaft. Gently pull the two wires off the old switch and slide onto the new switch. Then put the panel back. Read more...
Your Price
$39.02
  In Stock
Igniter Switch
PartSelect Number PS437308
Manufacturer Part Number 316032000
When the gas burner valve knob is depressed and turned, this part creates a spark that lights the gas and starts the burner.
Your Price
$57.36
  Special Order
Door Switch
PartSelect Number PS452926
Manufacturer Part Number 5301314211
Installation Instructions
Joseph from MIAMI GARDENS, FL
Over door light needed to be replaced
Pulled out the old light on the front of the door house where the door closes and replaced the door light switch Read more...

Related Parts