My Orders
Frigidaire Dishwasher Pumps
GET YOUR OFFICIAL Frigidaire PARTS TO ENSURE VICTORY
Popular Frigidaire Dishwasher Pumps
This is a drain pump assembly for various compatible models of dishwashers, that is responsible for draining the water from the dishwasher after every cycle. This drain pump assembly is made of plastic and fits within the sump assembly, which controls the flow of water into the drain. This drain pump assembly is a genuine OEM part and is made of a high-quality plastic but is sold as an individual component without any other parts, like its drain pump check ball which works within the pump to prevent water from backwashing into the pump, as well as the drain pump cover. If you notice your dishwasher is not draining or has a lot of water buildup at the bottom of the sump assembly, this filter may be damaged, clogged or broken, and in need of a replacement. To replace this pump assembly, you will only need a Philips-head screwdriver, but should start by removing your dishwasher racks. Then, pull up on the lower spray arm, and drain trap to remove them. Next, rotate the spray arm support and pull that up to remove it, at which point you can remove the base and filter for the drain pump. With those out, you can use your Philips-head screwdriver to disconnect and remove the cover and drain pump assembly. With the pump removed, you can inspect it or install the new drain pump assembly, with the same hardware as before. Then it is as simple as reassembling the rest of your dishwasher, ensuring each connection point is fastened tightly.
This is a drain pump assembly for various compatible models of dishwashers, that is responsible for draining the water from the dishwasher after every cycle. This drain pump assembly is made of plastic and fits within the sump assembly, which controls the flow of water into the drain. This drain pump assembly is a genuine OEM part and is made of a high-quality plastic but is sold as an individual component without any other parts, like its drain pump check ball which works within the pump to prevent water from backwashing into the pump, as well as the drain pump cover. If you notice your dishwasher is not draining or has a lot of water buildup at the bottom of the sump assembly, this filter may be damaged, clogged or broken, and in need of a replacement. To replace this pump assembly, you will only need a Philips-head screwdriver, but should start by removing your dishwasher racks. Then, pull up on the lower spray arm, and drain trap to remove them. Next, rotate the spray arm support and pull that up to remove it, at which point you can remove the base and filter for the drain pump. With those out, you can use your Philips-head screwdriver to disconnect and remove the cover and drain pump assembly. With the pump removed, you can inspect it or install the new drain pump assembly, with the same hardware as before. Then it is as simple as reassembling the rest of your dishwasher, ensuring each connection point is fastened tightly.
Installation Instructions
William from FRANKLIN, TN
Dishwasher stopped draining
Under sink: Disconnected drain hose to garbage disposal, shutoff water feed, unplugged power.
Under Dishwasher:
Removed water feed connection.
On top of Dishwasher:
Removed screws anchoring it to cabinet.
Pulled dishwasher out and flipped down so it’s resting on the front.
Removed drain hose on drain pump.
... Read more
/>Removed 3 torx screws on pump, greased o-ring on new pump and reinstalled doing the reverse of these instructions.
Took 1 hour and now it works great!
Under Dishwasher:
Removed water feed connection.
On top of Dishwasher:
Removed screws anchoring it to cabinet.
Pulled dishwasher out and flipped down so it’s resting on the front.
Removed drain hose on drain pump.
Took 1 hour and now it works great!
Read less
This dishwasher drain pump assembly is a genuine OEM component designed to efficiently remove wastewater from the appliance after each cycle. By actively pumping water out of the tub, it prevents pooling and supports proper drainage, helping maintain optimal cleaning performance. A failing pump may result in standing water, poor drainage, or unusual noises during the drain cycle. This replacement part restores reliable operation and is compatible with select models from Frigidaire, Electrolux, White-Westinghouse, Tappan, and other affiliated brands. Installation involves disconnecting power and water, accessing the pump housing, and replacing the unit using existing electrical and hose connections. Model verification is recommended prior to installation.
This dishwasher drain pump assembly is a genuine OEM component designed to efficiently remove wastewater from the appliance after each cycle. By actively pumping water out of the tub, it prevents pooling and supports proper drainage, helping maintain optimal cleaning performance. A failing pump may result in standing water, poor drainage, or unusual noises during the drain cycle. This replacement part restores reliable operation and is compatible with select models from Frigidaire, Electrolux, White-Westinghouse, Tappan, and other affiliated brands. Installation involves disconnecting power and water, accessing the pump housing, and replacing the unit using existing electrical and hose connections. Model verification is recommended prior to installation.
The pump ejects the water from the unit.
The pump ejects the water from the unit.
Installation Instructions
Phillip Foster from Cleveland, OH
Dish washer would not drain
Repair was easy I removed the old drain pump by removing 1 clips with pliar & 1 band with a screw driver and replace the drain pump with the new one, I replace clip and the band. replace drain hose tighten down the band. I had to adjust the drain pump because it seem to be a little loud then the one I had to replace , now it works !
The pump ejects the water from the dishwasher.
The pump ejects the water from the dishwasher.
Installation Instructions
John from Alexandria, VA
Dishwasher would not drain
**** A stubby Philips screw driver will save you a lot of headache taking the two retaining screws out that hold the drain pump assembly to the hanging bracket *** An inspection mirror was also helpful trying to locate these screws.
I thought the pump impeller vane was possibly broken because the pump would not drain the dis ... Read more hwasher but it would energize and make a loud clicking/rumbling noise.
1) Drain water from the dishwasher. I used a piece of tubing and siphoned the water out. Remove front cover plate.
2) Turn off breaker and dsconnect two wires going into pump.
3) Remove the pump inlet. I kept the 4" rubber jumper piece attached when I took the pump out.
4) I had to disconnect the wash water feed line to be able to reach the hose clamp on the pump outlet.
5) Loosen hose clamp on the pump outlet if you can reach it, otherwise remove the two screws that hold the drain pump assembly in. There is one screw on each side of the pump. I used an inspection mirror to see the screws. I had to use a stubby Philips head screw driver to take the screws out.
6) Wrangle the drain section out and finish taking off the pump outlet hose clamp. Install new pump and work backwards to put it together.
When I pulled the pump out I found the impeller to be complete (not broken as I had thought) and I saw it had two small steel balls that sat in grooves. I think the two balls and groove act as a safety detent and disengage the pump if something big gets sucked in. I pushed down on the impeller and everything snapped together nicely. Since I already ordered a new pump and I had everything taken apart already I installed the new one but I think I could have just used the old one.
Hope this is helpful to someone else. Washer has worked fine since.
I thought the pump impeller vane was possibly broken because the pump would not drain the dis ... Read more hwasher but it would energize and make a loud clicking/rumbling noise.
1) Drain water from the dishwasher. I used a piece of tubing and siphoned the water out. Remove front cover plate.
2) Turn off breaker and dsconnect two wires going into pump.
3) Remove the pump inlet. I kept the 4" rubber jumper piece attached when I took the pump out.
4) I had to disconnect the wash water feed line to be able to reach the hose clamp on the pump outlet.
5) Loosen hose clamp on the pump outlet if you can reach it, otherwise remove the two screws that hold the drain pump assembly in. There is one screw on each side of the pump. I used an inspection mirror to see the screws. I had to use a stubby Philips head screw driver to take the screws out.
6) Wrangle the drain section out and finish taking off the pump outlet hose clamp. Install new pump and work backwards to put it together.
When I pulled the pump out I found the impeller to be complete (not broken as I had thought) and I saw it had two small steel balls that sat in grooves. I think the two balls and groove act as a safety detent and disengage the pump if something big gets sucked in. I pushed down on the impeller and everything snapped together nicely. Since I already ordered a new pump and I had everything taken apart already I installed the new one but I think I could have just used the old one.
Hope this is helpful to someone else. Washer has worked fine since.
Read less
This circulation pump and motor assembly is a key component in the dishwasher’s wash system, responsible for driving water through the spray arms to ensure thorough cleaning. Designed for installation within the lower section of the appliance, it includes two O-ring seals to prevent leaks and maintain a watertight connection. This assembly restores proper water circulation and pressure, resolving issues such as poor cleaning performance, water not draining, unusual noises, or visible leaks. Replacing a faulty pump and motor helps maintain the dishwasher’s efficiency and extends its service life. Installation may require access to the base of the unit and basic tools.
This circulation pump and motor assembly is a key component in the dishwasher’s wash system, responsible for driving water through the spray arms to ensure thorough cleaning. Designed for installation within the lower section of the appliance, it includes two O-ring seals to prevent leaks and maintain a watertight connection. This assembly restores proper water circulation and pressure, resolving issues such as poor cleaning performance, water not draining, unusual noises, or visible leaks. Replacing a faulty pump and motor helps maintain the dishwasher’s efficiency and extends its service life. Installation may require access to the base of the unit and basic tools.
Installation Instructions
John from Herndon, VA
replaced dishwasher motor
Single-handedly. Tipped dishwasher on its side for easy access to water and electric connections. Went back together with no problems or leaks, washes quiter than ever.
MAKE THIS REPAIR A GUARANTEED WIN
OVER 2 MILLION PARTS TO ENSURE VICTORY
This dishwasher circulation pump and motor assembly is a vital component that ensures powerful water flow through the spray arms for thorough cleaning and efficient draining during each cycle. Engineered for consistent water pressure, it helps reduce noise while improving overall durability and performance. Installation is simple—disconnect power, remove the old assembly, and secure the new unit in place. This part is an ideal solution for issues such as poor cleaning results, failure to start, water not filling or draining, leaks, or unusual noises during operation.
This dishwasher circulation pump and motor assembly is a vital component that ensures powerful water flow through the spray arms for thorough cleaning and efficient draining during each cycle. Engineered for consistent water pressure, it helps reduce noise while improving overall durability and performance. Installation is simple—disconnect power, remove the old assembly, and secure the new unit in place. This part is an ideal solution for issues such as poor cleaning results, failure to start, water not filling or draining, leaks, or unusual noises during operation.
This genuine drain pump from Frigidaire is a crucial part of your dishwasher's functionality. It operates to effectively remove water from the tub during the drain phase of the dishwashing cycle, ensuring optimal performance every time you run your machine. The product is specifically designed to fit some models of Frigidaire, Electrolux, White Westinghouse, and Tappan. It's paramount to confirm that your model is compatible with the A00044305 drain pump before making a purchase, as even small variations in size and shape can affect functionality. Installation involves turning off and unplugging your dishwasher, and we recommend wearing work gloves for personal safety. Durchase this Frigidaire drain pump for a seamlessly operating dishwasher.
This genuine drain pump from Frigidaire is a crucial part of your dishwasher's functionality. It operates to effectively remove water from the tub during the drain phase of the dishwashing cycle, ensuring optimal performance every time you run your machine. The product is specifically designed to fit some models of Frigidaire, Electrolux, White Westinghouse, and Tappan. It's paramount to confirm that your model is compatible with the A00044305 drain pump before making a purchase, as even small variations in size and shape can affect functionality. Installation involves turning off and unplugging your dishwasher, and we recommend wearing work gloves for personal safety. Durchase this Frigidaire drain pump for a seamlessly operating dishwasher.
This pump moves water efficiently. Replace if circulation weakens or noises develop. This part is designed to keep your appliance operating reliably and efficiently. Replacing a worn or failing component helps prevent further issues and can extend the overall lifespan of your unit.
This pump moves water efficiently. Replace if circulation weakens or noises develop. This part is designed to keep your appliance operating reliably and efficiently. Replacing a worn or failing component helps prevent further issues and can extend the overall lifespan of your unit.
This drain pump assembly removes wastewater to support proper drainage and prevent standing water. Efficient pumping helps maintain smooth operation and performance reliability. Replacing a failing pump restores effective drainage and quiet operation.
This drain pump assembly removes wastewater to support proper drainage and prevent standing water. Efficient pumping helps maintain smooth operation and performance reliability. Replacing a failing pump restores effective drainage and quiet operation.
The pump removes the water from the dishwasher tub during the drain phase of the dishwashing cycle.
The pump removes the water from the dishwasher tub during the drain phase of the dishwashing cycle.