Frigidaire Dishwasher Racks

Frigidaire Appliance Parts
Shop By Part Type

Popular Frigidaire Dishwasher Racks

Your Price
$148.79
  In Stock
Upper Dishrack with Wheels
★★★★★
★★★★★
(6)
PartSelect Number PS2379463
Manufacturer Part Number 5304475618
This dish rack includes the wheels. It is used in the dishwasher.
Installation Instructions
Robert from CARNEGIE, PA
wheel assembly rusted and 1 wheel fell off causing rack to fail
replacing dishrack was simply removing old and sliding new onto track. however, removing and reinstalling water dispenser blade mounted on bottom of existing rack to new rack required much more time and effort .I needed to use flat screwdriver to pry plastic clamps apart and then a pair of channel locks to release assembly from original rack. It took some effort to finally accomplish . I believe all models that use this replacement rack would have this same issue with the dispenser blade and instructions for re-installation should accompany the new rack or better yet, new blade should be included on rack for those not familiar with using tools. Read more...
Your Price
$130.90
  Special Order
Lower Dishrack Assembly
★★★★★
★★★★★
(16)
PartSelect Number PS9494212
Manufacturer Part Number 808602402
This lower dishrack assembly comes with 8 rollers enabling it to roll in and out with ease. The dishrack is approximately 22 inches long x 20 inches wide. The dishrack holds dishes in place during the dishwashing cycle. If you see rust spots on the dishes, the lower rack will not pull out, or the lower rack is visibly rusted or damaged, the part should be replaced. Other common symptoms include: unusual or loud noises coming from the unit, or the dishes on the lower rack not being washed properly. This part is also known as a dish rack or a dishwasher rack.
Installation Instructions
Deb from MARIA STEIN, OH
Needed to replace some racks that were rusted and coming apart
All we had to do was remove the old racks and pop in the new. Very easy to do! Read more...
Your Price
$141.94
  Special Order
Lower Dishrack
★★★★★
★★★★★
(6)
PartSelect Number PS2379469
Manufacturer Part Number 5304475624
This lower rack does NOT include the wheels. Must be ordered separately.
Your Price
$125.09
  Special Order
Upper Rack Assembly - T3 PRO
★★★★★
★★★★★
(6)
PartSelect Number PS10065024
Manufacturer Part Number A01986801
Upper Rack Assembly - T3 PRO. This is the complete upper rack and the wash arm.
Fixes these symptoms
Installation Instructions
Keith from Coventry, RI
Center spray arm broke
I was able to pull out the top basket were the glasses are put then I lined up the back and the center plastic clip an slid on the center spray arm. It took about 2 miniutes Read more...
Your Price
$41.74
  In Stock
Silverware Basket - White
★★★★★
★★★★★
(5)
PartSelect Number PS1765528
Manufacturer Part Number 5304461023
This silverware basket is a genuine OEM replacement part for your dishwasher. If your current dishwasher is making unusual noises, or the silverware is not getting clean, replacing this part can solve the problem. Installing this part requires no disassembly, simply unhook the current basket and fit this one into place.
Installation Instructions
Robert from PORTSMOUTH, NH
Replace Dishwasher basket
Simply remove the old basket and replace with the new basket Read more...
Your Price
$47.93
  In Stock
Upper Dishrack Slide
★★★★★
★★★★★
(1)
PartSelect Number PS1525080
Manufacturer Part Number 154597801
This is an upper dishrack slide for your dishwasher. It is mounted to each side of the upper cabinet wall. The dishrack wheels roll inside this track, which guides the upper rack. The mounting screws are not included in this purchase and can be found in the related parts section below. You should purchase a new dishrack slide if your current one has been warped or damaged over time.
Installation Instructions
Terry from Pleasant View, UT
Top rack was dropping out of rollers/Slides
This was the second part of repair. Left side was constantly falling out of the slide. I replaced the same items as above minus the gasket and screw kit. Once done, the right side was sloppy so I orders part for that side plus gasket which slid right in.
1. Removed stops on front end of Upper Dishrack Slide on both sides.
2. Removed Upper Dishrack
3. Remove Roller and Axle/clip (4 each)
4. Push Roller onto Axle on all 4 kits
5. Install all 4 roller kits on Upper Dishrack
6. Remove stops from back end of Upper Dishrack Slides.
7. Remove both Slides
8. Remove 8 each Tub Wheels.
9. Using old or new Screws and Washers, install new Tub Wheels.
10. Install both Upper Dishrack Slides ensuring that small holes are toward the back.
11. Install stops on the back end of Slides.
12 Install Upper Dishrackinto slides
13. Install front stops on slide
14. Pulled out Gasket
15. Install replaced Gasket
Read more...
Dishwasher Upper Dish rack with Wheels
PartSelect Number PS10062929
Manufacturer Part Number 5304498211
It is used to replace the upper dishrack in dishwashers and it comes with wheels
Single Rack Roller Kit
PartSelect Number PS452448
Manufacturer Part Number 5300809640
This kit comes with one axel/clip and one wheel/roller.
Upper Dishrack Assembly
PartSelect Number PS10062926
Manufacturer Part Number 5304498202
Upper Dishrack Roller and Axle Kit
★★★★★
★★★★★
(1)
PartSelect Number PS452630
Manufacturer Part Number 5300809974
The upper dishrack roller and axel kit comes with two pieces, a wheel and an axle. This kit is made for your dishwasher. Both pieces measure to be roughly one square inch each, they are made entirely of plastic, and are white in color. The purpose of these parts is to allow your dishrack to roll easily on the support rails. This kit is sold individually and contains only one wheel and one axle. Please order the required quantity for your repair. If your dishrack is having trouble rolling in and out you may need replace your rollers and axles.
Installation Instructions
Terry from Pleasant View, UT
Top rack was dropping out of rollers/Slides
This was the second part of repair. Left side was constantly falling out of the slide. I replaced the same items as above minus the gasket and screw kit. Once done, the right side was sloppy so I orders part for that side plus gasket which slid right in.
1. Removed stops on front end of Upper Dishrack Slide on both sides.
2. Removed Upper Dishrack
3. Remove Roller and Axle/clip (4 each)
4. Push Roller onto Axle on all 4 kits
5. Install all 4 roller kits on Upper Dishrack
6. Remove stops from back end of Upper Dishrack Slides.
7. Remove both Slides
8. Remove 8 each Tub Wheels.
9. Using old or new Screws and Washers, install new Tub Wheels.
10. Install both Upper Dishrack Slides ensuring that small holes are toward the back.
11. Install stops on the back end of Slides.
12 Install Upper Dishrackinto slides
13. Install front stops on slide
14. Pulled out Gasket
15. Install replaced Gasket
Read more...

Related Parts