Amana Range Switches

Amana Appliance Parts
Shop By Part Type

Popular Amana Range Switches

Your Price
$60.56
  In Stock
Surface Burner Element Switch, Large Burner
★★★★★
★★★★★
(31)
PartSelect Number PS11740783
Manufacturer Part Number WP3149400
This surface burner element switch is for an 8-inch surface burner on an oven, stove, or range. The element switch controls the heat of the surface burner. Disconnect power to your range before completing this repair because you will be working closely with electrical circuits. Remove the screws from back panel and the console, and remove the console to expose the switch. It is recommended to check for overheating or arcing on the wiring harness in case they need to be replaced as well. The harness that connects to the switch features a slip-on terminal for easy installation.
Fixes these symptoms
  • Element will not heat
  • Oven is too hot
  • Will not program
  • See more...
Installation Instructions
chaz from fairplay, CO
the element did not turn compleatly off, the on light stayed on.
removed the screws holding the back metal panel, this exposed the wires to the switch. tested the wires to find that they were live when the switch was in the off position. ordered a new switch. UNPLUGED THE STOVE. removed the knob on the front of the stove. this exposed 2 screws, removed screws and the switch came away from the stove. removed each wire from the old switch and replaced them in the same position on the new switch. inserted new switch into the stove and attached the 2 screws. replaced back panel and pluged in stove. all tested well Read more...
Your Price
$73.41
  In Stock
Dual Element Control Switch
★★★★★
★★★★★
(10)
PartSelect Number PS11754687
Manufacturer Part Number WPW10434452
This switch controls the stove top surface burner.
Fixes these symptoms
Installation Instructions
Dale from POUND, WI
Switch worked off and on but you could not set heat to a specified temperature.
Remove back panel 10 screws. Disconnect plug in fixture from switch. Front of range remove knob (it just pulls out) remove 2 screws, remove switch. To install reverse procedure. Read more...
Your Price
$59.59
  In Stock
Infinite Control Switch, 6"
★★★★★
★★★★★
(8)
PartSelect Number PS11740785
Manufacturer Part Number WP3149404
This switch controls the stove top 6" surface burner.
Fixes these symptoms
Installation Instructions
Bruce from Pasadena, MD
The old switch broke off.
Removed two screws that held the unit in then pulled out a few inches so I could see where the 5 wires were. Then I replaced one at a time till done. then replaced the retaining screws. Read more...
Your Price
$53.03
  In Stock
Range Infinite Burner Switch - 8 Inch
★★★★★
★★★★★
(18)
PartSelect Number PS11744487
Manufacturer Part Number WP7403P239-60
This infinite switch is for 8-inch range burners. When an element is unable to produce any heat on a modern oven, the problem may lie with the infinite switch. This switch is responsible for sending power to the surface elements. Check the element and terminal block to ensure they are working properly. If they are in working order, check the infinite switch at the control panel for any wires that have overheated, or broken terminals to or from the infinite switch. If the infinite switch is damaged or malfunctioning, it will need to be replaced. Remember to unplug your range before beginning this repair.
Fixes these symptoms
Installation Instructions
Dennis from Hagerstown, MD
The Burner was getting too hot and you could not regular the tempature
Moved the Appliance out unplugged it and removed the backing plate then Remove the Knob and unscrew the infinite switch then marking the 5 wires to know where the go on the new switch, removing and replaced it with the new one Read more...
Your Price
$59.20
  In Stock
Infinite Switch - 6 Inch
★★★★★
★★★★★
(3)
PartSelect Number PS11740774
Manufacturer Part Number WP3148952
This part carries 5.2-6.6 amps.
Fixes these symptoms
Installation Instructions
Mikhail from Iowa City, IA
One of the heat elements in my oven would not heat
1. Disconnected power from my oven.
2. Removed several screws that held the control block
3. Removed two screws that held the switch itself disconnected wires and removed switch
4. Reconnected all wires to new switch (no soldiering gun required)
5. Put control block back

Overall - very easy
Read more...
Your Price
$78.72
  In Stock
Dual Surface Burner Switch Kit
★★★★★
★★★★★
(13)
PartSelect Number PS2003583
Manufacturer Part Number 12002125
This switch is used to operate the dual surface burner.
Fixes these symptoms
Installation Instructions
Michael from Collierville, TN
Outer element of dual element burner didn't work
Remove Ceran Galss top by removing hex screws below the rim. Also remove the two opposing screws in the center of the downdraft opening. Ceran top comes off easily now.
The instructions with the new switch were very poorly written, so here is how I got the new switch to work:
Attach the black wire(s) from the old switch (terminal 2) to the new switch terminal P1. Also attach the jumper cable to P1 and "jump" it to S1.

Attach the orange wire (old switch terminal 5) to S2
Attach the yellow wire (old switch terminal 4) to 4a
Attach the tan/(white?) wire (old switch terminal 3) to terminal 4 on the new switch
Attach the single red wire from the right front element to terminal 2 on the new switch.
Attach the 'compound' red wires (the ones that come from the left rear/outlet connection and is also attached to the right rear switch) to terminal P2 on the new switch.
There is no need to seperate the compound red wires as the instructions might lead you to believe.
Good Luck
Read more...
Your Price
$65.33
  In Stock
Infinite Switch - 8 Inch
★★★★★
★★★★★
(2)
PartSelect Number PS11744412
Manufacturer Part Number WP74010824
Sold individually.
Fixes these symptoms
Installation Instructions
Pete from Longwood, FL
center element of triple burner was not working.
I pulled the unit out from the wall. Took the screws out along the sides. Removed screw holding the front controls loose. First I changed the control switch which was very easy. Two screws and a couple of wires. The burner was a bit more tricky. I had propped the glass cook top up so I would not have to disconnect to many wires. Took out the screws holding the burner in place and disconnected the wires. I removed the clips from the old burner and attatched them to the new burner, then reinstalled the new burner. The only real problem was the wires. I forgot the order of a couple of them. I was able to check on line and get the correct order. Read more...
Your Price
$55.81
  In Stock
Surface Element Switch
★★★★★
★★★★★
(3)
PartSelect Number PS12070192
Manufacturer Part Number W10900107
Fixes these symptoms
Installation Instructions
Edward from Malvern, AR
Burner would not heat
First i shut off the power since this is an electric cook top/range. I then removed the knob and the two screws that hold the burner switch in place. I removed the wires one at a time and connected each to the new switch. I then reattached the screws to the switch. The most difficult part to me was breaking off the switch stem at the right level. I got that done and finally selected the appropriate adapter for the stem/knob fit. Read more...
Your Price
$102.37
  In Stock
Infinite Dual Switch
★★★★★
★★★★★
(1)
PartSelect Number PS11749068
Manufacturer Part Number WPW10149355
Fixes these symptoms
Your Price
$73.48
  In Stock
Dual Surface Burner Switch
PartSelect Number PS11744018
Manufacturer Part Number WP74003122
This part has been updated by the manufacturer. This updated part now has 7 wire terminals instead of 5. The terminals are all labeled, however, the new switch needs to be tested before connecting the pilot lamp wire (P). To test the new switch: 1) Connect the Line Wires (L1 and L2), connect the Load Wires (H1 and H2). 2) Do not connect the pilot lamp (P) wire yet. 3) Reconnect the power to the range and turn on the new switch and one other switch. 4) Connect the leads of a volt meter on L1 of the new switch and P of the other switch you turned on. 5) If the volt meter reads 220V, the L1 and L2 wires on the new switch must be reveresed. 6) Disconnect power, reverse Line Wires if needed and connect the P wire. 7) Reconnect power to the range after reassembly.
Fixes these symptoms
Installation Instructions
Robert from Medina, OH
The old switch would not regulate the temperature - running too hot
flipped off breaker
Pulled the stove from the wall about 2 feet
Removed back cover (4 screws)
looked at existing switch - it was different than the new switch, but the instructions were spot on for the retrofit
I marked the back of the new switch with the retrofit locations of the wires
pulled off the knob
removed 2 screws from the front of the range that holds the switch
removed old wires using needle nose pliers
attached new switch re-using same 2 screws from the front
one at a time attached the wires to their proper location
pushed knob back on
reset the breaker
tested the new switch - all was OK
switched off breaker again
replaced the back cover
slid range back in place
Breaker back on
finished
Read more...

Related Parts