Porter Cable Parts

This head valve body regulates airflow within pneumatic nailers, helping generate the pressure needed to drive fasteners effectively. Built from durable materials, it supports consistent tool performance. Replacing a worn or faulty valve can resolve issues such as air leaks, reduced driving power, or failure to fire, restoring reliable operation.

Length: 8' Gauge: 18 Wires: 2 Type: Bare Wire This cord is a genuine DeWalt replacement part. This cord is compatible with the list of models below. This part is made for double insulated tools It is a two wire cord with two prongs and does not need a ground wire. The cord is sold individually. Installation of this part requires the new cord wires to go correctly into wire terminals also routing the cord and wires in the right path can help avoid pinching when the tool case (Plate) is put back into place.

Genuine Porter Cable replacement part Includes 1 Carbon Brush with wire lead attached. • Worn brushes are often the cause of a poorly running motor • Replacing brushes can fix an intermittent motor • New brushes can restore a motor's electric braking Carbon motor brushes are one of the most commonly replaced power tool components. • Because carbon brushes are wear items, meaning that through friction and use they will gradually wear away, they will eventually require replacement. • Worn brushes are common causes of intermittent motor function, reduced electric braking, and reduced motor power. • A worn out brush will often be worn down near the wire lead and may be cracked, pitted, or burned. • When replacing carbon brushes, be sure to also inspect your armature for burns, cracks, or other damage which indicates a larger motor problem.

The 151281-08 Pad is used to hold 5 inch Hook and Loop sandpaper with 8 vacuum holes. Over the past few years the popularity of Hook and Loop paper has grown because of the ease of changing sandpaper when needed. Over that of the PSA (Pressure Sensitive Sandpaper) Applying too much pressure on the sander may cause premature wear on the Hook and Loop pad. When a pad needs to be replaced, simply remove the three screws that hold the pad to the sander, then replace it with a new pad.

This brush is a genuine Porter-Cable replacement part, not generic. As pictured, this brush is ready to install and includes carbon brush, wire lead, and spring. This item is sold individually. Over time, brushes will wear down and eventually require replacement. This brush will fit the models listed in the 'Compatibility' section below. It is not guaranteed to fit any other power tool models. • Worn brushes are often the cause of a poorly running motor • Replacing brushes can fix an intermittent motor • New brushes can restore a motor’s electric braking Carbon motor brushes are one of the most commonly replaced power tool components. Because carbon brushes are wear items, meaning that through friction and use they will gradually wear away, they will eventually require replacement. Worn brushes are common causes of intermittent motor function, reduced electric braking, and reduced motor power. A worn out brush will often be worn down near the wire lead and may be cracked, pitted, or burned. When replacing carbon brushes, be sure to also inspect your armature for burns, cracks, or other damage which indicates a larger motor problem.

Frequently referred to as a Drain Plug, this Drain Valve is used to drain any condensation that has collected inside the tank to prevent the tank from rusting. It is not part of a kit or assembly, is sold individually, made of brass, is gold, and will be found at the bottom of the air tank. This part will need to be replaced when it is no longer able to provide a proper seal, or if it is visibly worn or damaged. You will need a wrench to complete this repair. Customers rate this repair as Easy.

This is a genuine Porter Cable replacement part, it is sold individually. The purpose of the 890725 Retainer is to secure the pins used on the model numbers shown below. It is advised to check the condition of the retainer often, for the reason the do deteriorate over time and can fall off of the pin they are retaining.

(Sold Individually) This motor brush is for grinders. The motor brush transfers electric current to the spinning armature in the motor. Unplug the grinder before installing this part. Wear work gloves to protect your hands.

This sander pad is a genuine Dewalt replacement part, not generic or aftermarket. It it a Foam Rubber type pad and is compatible with clamp-on style sandpaper. It is not compatible with hook-and loop sandpaper. This sander pad has a metal backing plate with a padded sanding surface attached. The pad is complete and ready to install. This sander pad will fit the Dewalt sanders listed in the 'Compatibility' section below. It is not guaranteed to fit any other power tool models.

This Ball Bearing is sealed on both sides. It is a genuine DeWalt replacement part and is sold individually. • Ball bearings are used to reduce friction between rotating parts.. The balls or rollers take the load and spin, distributing the weight evenly while the minimal contact area of the ball reduces friction. This reduces wear on the tool and allows it to run smoothly. • Bearings experience constant wear when the tool is in operation from pressure, heat, vibration and friction. Because of this, many Bearings need periodic maintenance or replacement.