Porter Cable Sander Parts

Genuine Porter Cable replacement part includes 1 Carbon Brush with wire lead and brush spring attached.rn • Worn brushes are often the cause of a poorly running motor • Replacing brushes can fix an intermittent motor • New brushes can restore a motor's electric braking Carbon motor brushes are one of the most commonly replaced power tool components. • Because carbon brushes are wear items, meaning that through friction and use they will gradually wear away, they will eventually require replacement. • Worn brushes are common causes of intermittent motor function, reduced electric braking, and reduced motor power. • A worn out brush will often be worn down near the wire lead and may be cracked, pitted, or burned. • When replacing carbon brushes, be sure to also inspect your armature for burns, cracks, or other damage which indicates a larger motor problem.

This Pad is designed for the "Adhesive Backed" Sanding Pads.rnThe (PSA) sander pad is a direct replacement for many Dewalt orbital sanders. It is a genuine Dewalt part, not off-brand. It features a foam body attached to a metal backing plate. It also has a sturdy smooth style bottom for use with sticky adhesive sandpaper. This pad does not have vacuum holes. It is 5" in diameter. This pad is compatible with the Dewalt sanders listed below. This pad is interchangeable with sanders fitted with 5" hook-and-loop pads. If you prefer to fit your sander with hook-and-loop sandpaper instead of adhesive, you will need the hook-and-loop pad listed under "Related Products" below. Model compatibility is the same.

This cord is a genuine Porter Cable replacement part and is sold individually. It is constructed with tough, thick outer rubber insulation for a long service life. Power Cord Specifications: • 3 Prongs • 3 Wires • 18 Gauge • 7 Feet Long • Porter Cable models: 6302 T4, 6902 T5, T6

This replacement switch is a high quality item sourced directly from original equipment manufacturer. It is specially made for used on Dewalt and Porter Cable power tools. It is the part that allows user to turn the tool on and off. These mechanical switches will over time wear our and fail requiring replacement. It is made out of durable plastic material and it is sold individually. No tools needed to replace this switch, it is secured with a pair of tabs on each side.

The spindle and bearing assembly goes between the eccentric hsg and the sander pad. It is made of metal and is sold individually. This part is an OEM from Porter Cable for use in sanders and polishers. A screwdriver and a set of pliers may be helpful when replacing this item. Over time this part may break and will need to be replaced.

O-rings are made to contain thousands of PSI pressure by creating a seal between two or more parts. O-ring measurements are defined by the inside diameter and the thickness. There are many causes for O-ring failure. The most common among power tools are: • The O-ring has ragged, tattered edges. These are commonly caused by pressure spikes which shear off tiny "bites" from the O-ring, or caused by clearance gaps. • One or both sides of the O-ring appear rough and slightly flattened. Commonly caused by a contact surface that is too rough, contains grit, or is too smooth to allow lubrication. • The O-ring is flattened on both sides and may have a "ring" split along its length. Commonly caused by excessive pressure or heat. • The O-ring has a pitted or cracked surface, and is often flattened on both sides. Caused by temperature exceeding O-ring capacity. • The O-ring is covered in small surface cracks. Caused by exposure to ozone, UV rays, and air pollution. Excessive seal stretching (greater than 5%) causes similar cracking.

This manufacturer sourced replacement part is designed for use with Delta and Porter Cable power tools. The purpose of the brush cap is to secure the carbon brush in the tool. This item is made from durable plastic and it is sold individually, to secure or remove it you will need a flat-head screwdriver.

Genuine Porter Cable replacement part. • Pad Dimensions: 9" by 4-1/2". Includes one pad. • Sturdy Felt Backing for long life. • Conveniently easy to take on and off. • 4 screw holes to keep your pad firmly attached. Can use existing screws on your tool, or go to the schematics page for your tool to find and order new screws.

This is a genuine item that is supplied by the original equipment manufacturer for use with Porter Cable polishers and sanders. It is an identical replacement for a missing or damaged counterweight that was originally installed on a new unit, please make sure to refer to the appropriate diagrams of your model for the correct location and application of this hardware. This high-quality part is made of durable metal and is sold individually, keep in mind the hardware to secure it is sold separately.

This replacement wrench is specially designed for Porter Cable sanders. This authentic part is sourced directly from original equipment manufacturer. It is used to allows you to change the back up pad. Angular profile of this item makes tightening/loosening hardware extremely easy. This wrench is made from metal and it is sold individually.