3VET2 Whirlpool Refrigerator - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Compressor making excessive noise
5 of 9 people
found this instruction helpful.
-
chester from Tampa, FL
- Easy
- 30 - 60 mins
-
Nutdriver, Socket set
One front roller was flat on one side. Decided to replace all rollers at same time. Placed shims under unit and removed mounting screws for one front and one rear roller. With new rollers in place, I was able to level the refrigerator side to side, but unable to do so, front to back. Left the new front roller in place and reinstalled
... Read more
the old rear roller. Have decided to replace refrigeratorin the near future. This is one of my few repair failures!
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
gasket was cut and ripped
3 of 3 people
found this instruction helpful.
-
Herbert from NIAGARA FALLS, NY
- Really Easy
- 30 - 60 mins
-
Screw drivers
rippped the old one off and carfully put the new one on with a flat head screwdriver at an angle as not to rip the new one
Was this helpful?
Thank you for voting!
My pan crisper is broken.
4 of 7 people
found this instruction helpful.
-
Raymond from Westford, MA
- Really Easy
- Less than 15 mins
The repair story webpage has some problems. I want to rate it "very helpful" but it showed "not helpful". I am pleased with the order service. It was very hard to find the parts on the web. There are a couple of web sites but only partselect has it in inventory. I ordered it, and it came in within 5 days. Excellent service. Will c
... Read more
ontinue to order parts from this site in the future.
Read less
Was this helpful?
Thank you for voting!
Broken track replacement
3 of 4 people
found this instruction helpful.
-
William from Crookston, MN
- Really Easy
- Less than 15 mins
The majority of the repair time was spent moving the items in the refrigerator off the glass top under which the track was to be placed. After that, the track was a cinch to put in its place (it's pretty idiot-proof). Perhaps the track wouldn't need replacement if it were made of something stronger than plastic, but I felt pretty handy
... Read more
doing this for my wife, and she's glad to have the hydrator drawers back in proper operation.
Read less
Was this helpful?
Thank you for voting!
A bottle broke the glass bottom shelf.
3 of 4 people
found this instruction helpful.
-
robert from san diego, CA
- Really Easy
- Less than 15 mins
The best part was that it took 2 minutes to order the part on the internet, and the part was delivered in three days. Earlier than expected. it was packaged very well amd I was able to transport it to the refrigerator in our vacation home with out hiring a repairman or additional delay.Thanks.
Was this helpful?
Thank you for voting!
Freezer door handle needed to be replaced
3 of 4 people
found this instruction helpful.
-
Lynda J from Lago Vista, TX
- Really Easy
- Less than 15 mins
-
Screw drivers
First I took a Phillips head screwdriver to the top bracket of the fridge and removed the two screws on top and removed the screws out of the bottom of the freezer door, then placed the new freezer handle into the holes of the old one and reattached the screws to the new handle. The customer service rep. that got me the correct sized hand
... Read more
le, knew the correct size as the lower fridge handle is longer than the freezer handle of 11 inches. You cannot even tell that the handle has been replaced.
Read less
Was this helpful?
Thank you for voting!
door handle broken off
3 of 4 people
found this instruction helpful.
-
LAURA from JOLIET, IL
- Really Easy
- Less than 15 mins
-
Screw drivers
This was the easiest project ever!! I took the screws out of what was left of the old handles and used them to attach the new ones!
Was this helpful?
Thank you for voting!
defective light switch
3 of 4 people
found this instruction helpful.
-
THOMAS from WILLARD, OH
- Really Easy
- Less than 15 mins
inserted a knife between the switch and the plastic interior in order to pop the switch out.
then took off the 2 wires on the old switch put them on the new switch and reinserted the switch into the plastic interior.
then took off the 2 wires on the old switch put them on the new switch and reinserted the switch into the plastic interior.
Was this helpful?
Thank you for voting!
the light socket broke apart
4 of 7 people
found this instruction helpful.
-
Elyse from Skokie, IL
- Really Easy
- 15 - 30 mins
-
Screw drivers
I took out the old socket by moving a clip. Reattached the electrical wires, clicked in the socket and that was it.
Was this helpful?
Thank you for voting!
Cracked Icemaker Water Fill Tube
4 of 7 people
found this instruction helpful.
-
James from Ft. Lauderdale, FL
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
The plastic part that connects the fresh cold water to the ice maker in back of the fridge cracked.
Do to the fact that Whirlpool has the part stick out on the back top part of the fridge. So if you push the fridge just an inch too far back the plastic part will crack.
I ordered (The Part S&H)- came to about, $11.00.
... Read more />1. Turned off the cold water under the sink.
2. In the back of the freezer section. I unscrewed the two screws that held the old broken part to the fridge.
3. I opened the freezer section and cleared out the top shelf till I could see the back of the fridge.
4. I removed the old plastic part by pushing & wiggling it about forward and it then extended out the back of the freezer side and then I pulled it out the back and it came out.
5. I slid the new replacement part in basically the reverse of step 4.
6. I connected the hose in the back. To the new, replacement plastic part, that fills the automatic ice tray with water.
7. Once finished I glued a small 2”x2” piece of wood next to the new part so the fridge will never get too close to the back wall so to never break that part that sticks out again.
Before just a small bump could break the part and water is everywhere and this leak could happen slowly at first and the next day what a mess.
Some fridges have this part recessed into the back of the fridge so this would never happen as my other fridge has.
Also, this might seem like more work then it was. It was very simple. I was scared I'd screw it up, but just did it step by step. If I had someone do it. It would have cost me a bundle.
It took more time to type this, then to do the work.
I had no instructions to follow, but again, was easer then I thought it would be.
I hope that this was helpful,
Jim Vourakis
Do to the fact that Whirlpool has the part stick out on the back top part of the fridge. So if you push the fridge just an inch too far back the plastic part will crack.
I ordered (The Part S&H)- came to about, $11.00.
... Read more />1. Turned off the cold water under the sink.
2. In the back of the freezer section. I unscrewed the two screws that held the old broken part to the fridge.
3. I opened the freezer section and cleared out the top shelf till I could see the back of the fridge.
4. I removed the old plastic part by pushing & wiggling it about forward and it then extended out the back of the freezer side and then I pulled it out the back and it came out.
5. I slid the new replacement part in basically the reverse of step 4.
6. I connected the hose in the back. To the new, replacement plastic part, that fills the automatic ice tray with water.
7. Once finished I glued a small 2”x2” piece of wood next to the new part so the fridge will never get too close to the back wall so to never break that part that sticks out again.
Before just a small bump could break the part and water is everywhere and this leak could happen slowly at first and the next day what a mess.
Some fridges have this part recessed into the back of the fridge so this would never happen as my other fridge has.
Also, this might seem like more work then it was. It was very simple. I was scared I'd screw it up, but just did it step by step. If I had someone do it. It would have cost me a bundle.
It took more time to type this, then to do the work.
I had no instructions to follow, but again, was easer then I thought it would be.
I hope that this was helpful,
Jim Vourakis
Read less
Was this helpful?
Thank you for voting!
The water fill tube 90 fitting broke
3 of 4 people
found this instruction helpful.
-
Scott from Crete, IL
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Removed brokent tube fitting from the compression nut.
Removed two screws holding the fill tube. Removed and replaced the fill tube. Direct replacement, no cutting tube length. Reconnect water line to the new fill tube.......Done.
Removed two screws holding the fill tube. Removed and replaced the fill tube. Direct replacement, no cutting tube length. Reconnect water line to the new fill tube.......Done.
Was this helpful?
Thank you for voting!
changed the light bulb still would not work so I figured it was the switch sure enough.
3 of 4 people
found this instruction helpful.
-
anthony from HAVELOCK, NC
- Really Easy
- 15 - 30 mins
I took a chance and ordered a switch that is next to the top of the door. looked for how to remove it easily done in ten minutes works fine last long time.
Was this helpful?
Thank you for voting!
Fill tube on the icemaker was leaking.Looked at sears repair parts list and part was $62. I found the same part here for $4.99. Very easy to just remove the old part and replace it with the new. I also received the part in two days. Amazing!!!!
3 of 4 people
found this instruction helpful.
-
Walton from Woodland, PA
- Really Easy
- 15 - 30 mins
-
Pliers
Simlpy removed two screws to remove the old part. replaced the new part and put the two screws in. Job finished.
Was this helpful?
Thank you for voting!
Water fill tube broken
3 of 4 people
found this instruction helpful.
-
Jeffrey from Monroe, MI
- Really Easy
- Less than 15 mins
-
Screw drivers
removed two screws and pulled part out of the unit. The local appliance store said they needed model and part # to try to identify and order the part. Found part select online, found the part immediately, ordered the part for $4.50 or so. Part was delivered in 2 days! Very easy installation and the part works perfectly. Thanks so muc
... Read more
h!
Read less
Was this helpful?
Thank you for voting!
Missing shelf from refrigator that was in house I purchased.
3 of 4 people
found this instruction helpful.
-
Doris from TUSTIN, MI
- Very Easy
- Less than 15 mins
purchased shelf, installed shelf.
Was this helpful?
Thank you for voting!