3VET2 Whirlpool Refrigerator - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
fridge door switch did not work
2 of 2 people
found this instruction helpful.
-
stu from richmond, VA
- Easy
- Less than 15 mins
-
Socket set
I removed the switch housing (4 screws), replacing the switch in the housing was a snap. It took 5 minutes, cost $8 and light works like new!
Why didn't I order this part and do the repair earlier? Very simple.
Why didn't I order this part and do the repair earlier? Very simple.
Was this helpful?
Thank you for voting!
Defrost drain clogged with ice
2 of 2 people
found this instruction helpful.
-
Michael from CHICAGO, IL
- Easy
- 30 - 60 mins
-
Nutdriver
Replaced gaskets on both doors. Followed the online video link that came with emailed receipt. Worked exactly like demonstrated in the video.
Was this helpful?
Thank you for voting!
Broken plastic part at top of water fill tube to freezer
2 of 2 people
found this instruction helpful.
-
Jay from Mt. Pleasant, WI
- Really Easy
- 30 - 60 mins
-
Screw drivers, Socket set
Simple. 1st, removed broken part to understand part (water fill tube to freezer, plastic part at top of fill tube cracked). 2nd go on your web site and look at prints to find part number, Study video to understand video. 3rd. Called customer service and lady was very nice and efficient. Placed order and received. Study video again a
... Read more
nd installed. My 9 year old grandson was visiting from out of town and assisted in installation. Just over 30 minutes to install
Read less
Was this helpful?
Thank you for voting!
Ice buildup in freezer causing leaking water into fridge section
2 of 2 people
found this instruction helpful.
-
Diane from Brighton, MI
- Very Easy
- 30 - 60 mins
-
Nutdriver, Pliers
In my case the defrost thermostat was not the problem. Not worth going through the hassle of checking the thermostat as I would have had to cut it out and test it in another freezer (while the food that was in the freezer was being stored elsewhere). I just ended up buying it and replacing it. So, like I said the defrost thermostat was NO
... Read more
T the issue. I ended up getting a drain tube heater strap, and have been keeping my eye on the fridge. It hasn't been long enough to say the strap fixed the problem, but all indications are pointing to that being the case.
Read less
Was this helpful?
Thank you for voting!
Door would pop open. I cleaned gasket made sure nothing in the way of door. Gasket was cracked top and bottom it worked better but the seal was not good.
2 of 2 people
found this instruction helpful.
-
Roy from KAUFMAN, TX
- Really Easy
- 30 - 60 mins
-
Nutdriver
Did just like the video showed took doors off daughter helped take off doors so easy put door on blanket. My daughter 38 went to town putting it on just watch the corners so easy two days after installation the door seals great. You can do this.
Was this helpful?
Thank you for voting!
Crisper drawer rail broken at one end
2 of 2 people
found this instruction helpful.
-
MARTY from GREAT FALLS, MT
- Very Easy
- 30 - 60 mins
The rail just snapped into place with a light pressure. I worried it would require manipulation or heavy pressure and I would break the end while installing it.
Was this helpful?
Thank you for voting!
After 17 years, the old door gasket was split and showing signs of mold
2 of 2 people
found this instruction helpful.
-
duncan from HOWELL, NJ
- A Bit Difficult
- 15 - 30 mins
-
Screw drivers
The gasket has an inner lip that fits over the edge of the door plastic liner. The old gasket was removed by pulling it straight out, in the plane of the door. Try not to pull sideways as it could crack the door liner, which gets brittle with age. The new liner had a brown magnetic strip, which holds the door closed, and this fits behi
... Read more
nd the edge of the door liner. Start on the bottom of the door. A helper is useful to hold the gasket loosely vertical. A flat blade screwdriver can be used to pry away the liner to insert the new seal. Once you have worked in the lower edge, install both sides, and then the top. Some juggling side-to-side may be needed for an exact fit
Read less
Was this helpful?
Thank you for voting!
cut old off the door and put new on the door
7 of 17 people
found this instruction helpful.
-
George from Albakurky, NM
- Easy
- 30 - 60 mins
-
Socket set
took door of the refergarator. Then cut old gusket of and clipped the new one on and then put the back. Done!!!!!
Was this helpful?
Thank you for voting!
Screws are a bit small and short for the job
2 of 3 people
found this instruction helpful.
-
Sheryll Lawrence from BRONX, NY
- Really Easy
- 30 - 60 mins
-
Screw drivers
Using a screwdriver
Other Parts Used:
Was this helpful?
Thank you for voting!
End caps broke on the lower shelf
2 of 3 people
found this instruction helpful.
-
Eugene from Erie, PA
- Really Easy
- Less than 15 mins
Slid the end caps onto the shelf, placed the tape on the pieces as noted in the directions, and put the shelf back in place. Fast service, exact part, easy to find on the web site! Great!
Was this helpful?
Thank you for voting!
latch end of track broke when too full jammed drawer was forced
2 of 3 people
found this instruction helpful.
-
H. James from Bella Vista, AR
- Easy
- Less than 15 mins
PartsSelect diagrams at their website made it easy to find and order the right part at a reasonable price. I removed the lower glass shelf and frame that supports it. I removed broken track and slipped in the new track and snapped it in place with the orifice at the rear of the track over small peg in the back of the frame. If I had call
... Read more
ed a regular refrigerator repair man, i'll bet this job would have cost me at least 70 or 80 dollars,
Read less
Was this helpful?
Thank you for voting!
Metal end cap on freezer door handle broke
2 of 3 people
found this instruction helpful.
-
Annette Jones from Glendale, KY
- Really Easy
- Less than 15 mins
-
Screw drivers
Parts Select was easy to deal with -- had the item next morning after ordering! But Whirlpool should be ashamed -- this is the FOURTH time this part has had to be replaced in the 13 years we've had this refrigerator. Unrelated, but still a Whirlpool problem, the icemaker broke within 6 months -- had it repaired twice and then gave up.
... Read more
Will buy a different brand frig next time.
Read less
Was this helpful?
Thank you for voting!
Drawer cracked/split
4 of 9 people
found this instruction helpful.
-
Yvonne from Fredericksburg, VA
- Really Easy
- Less than 15 mins
I just slipped the new drawer into place. So easy, even a woman can do it! ( I am female!)
Was this helpful?
Thank you for voting!
Shelves in freezer falling off
2 of 3 people
found this instruction helpful.
-
wendy from palm coast, FL
- Really Easy
- Less than 15 mins
-
Screw drivers
Went online with the model number, the part was very easy to find, diagrams helped me to have confidence in the choice. Parts came in two days, tore them open and used a screw driver to replace the broken shelf brackets, replaced shelves, I am a happy camper!!
Was this helpful?
Thank you for voting!
Crisper Drawers were cracked
2 of 3 people
found this instruction helpful.
-
Luke from CENTER, TX
- Really Easy
- 15 - 30 mins
I replaced the cracked crisper drawers with the new ones just by sliding them in the bottom of the refrigerator. This did not solve the problem because one of the drawers was smaller than the other one and left a big space. When I ordered the Crisper Drawers I looked at the part diagram and it looked to me that the drawers were two differ
... Read more
ent sizes and thats what I ordered. I now need to order another large drawer to finish the repair.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!