EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

3847 - Instructions

All Instructions for the 3847
61 - 75 of 214

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Interior Light did not go on due to faulty switch
4 of 6 people found this instruction helpful.
  • Robert from Coto de Caza, CA
  • Really Easy
  • Less than 15 mins
I ordered two switches, replaced both with a knife in 10 minutes. Interior light works, thanks.
Was this helpful?
Thank you for voting!
Does not start , trips breaker
3 of 3 people found this instruction helpful.
  • Paul from RNCHO CORDOVA, CA
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
I pried the relay from compressor with small screwdriver, cut and replaced burnt wire going to relay,pushed new relay on compressor and wires unfortunately it did not fix the problem.
Was this helpful?
Thank you for voting!
freezer compartment worked fine but very little cooling going to refrigerator section.
3 of 3 people found this instruction helpful.
  • Lee from OZARK, AR
  • Really Easy
  • 30 - 60 mins
  • Screw drivers
Freezer worked great but no cooling to refrigerator section. Replaced with part ordered. Phillips head screw driver is all that is needed. Very easy to replace, it's plug and play. New part powered up neither the freezer nor the refrigerator. Went back to old part and atleast freezer still works. New part was no good from factory. The re placement part# matched the original. I attempted to contact PartsSelect but there was no response back.
Was this helpful?
Thank you for voting!
The original fan had its blades sheared by ice build-up
3 of 3 people found this instruction helpful.
  • Jeffrey from Broomfield, CO
  • Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers, Wrench set
The original design is poor. The evaporator fan is mounted in an upright position just below the ice-maker. A plastic grate mounts over the fan assembly to allow for air circulation. Unfortunately, random chips of ice from the ice maker can fall into the fan, causing the fan to shear its blades. Replacement of the fan blade is relativ ely simple (accept for having to completely unload the freezer and remove all back covers, the ice-maker auger motor assembly, and the metal evaporator cover). In order to mimimze this from reoccuring, I installed a 1/4'' mesh metal screen over the exhaust ports on the cover. Thus far, this has worked well to keep ice chips out of the evaporator fan.
Was this helpful?
Thank you for voting!
switchlight on my refrigerator was not working
5 of 10 people found this instruction helpful.
  • Eileen from Coto de Caza, CA
  • A Bit Difficult
  • 30 - 60 mins
  • Pliers
I found instructions on the web about how to do this repair, so I ordered the part with confidence. But the instructions simply said "pull out the old switchlight". That was actually somewhat difficult as the clip on the side intended to hold the part in was stubborn. I eventually used a utility to slice off the clip. From that point, it was just a matter of plugging in the new switchlight , which was very simple.
Was this helpful?
Thank you for voting!
end cap to bar of freezer door broke
3 of 4 people found this instruction helpful.
  • Kimberly A from Columbus, OH
  • Really Easy
  • Less than 15 mins
Snapped end cap onto bar and installed bar onto freezer door.

I considered going to an appliance parts store but found the part very easily on the internet and had it within 2 days. I am very busy which was very helpful.
Was this helpful?
Thank you for voting!
Condensor fan blade cracked, blade was sheared off.
3 of 4 people found this instruction helpful.
  • Bradley from Cedarburg, WI
  • Easy
  • Less than 15 mins
  • Pliers, Screw drivers
First, remove the cardboard cover on the back, lower portion of the refrigerator.

Next, locate the condensor fan motor assembly and blade. (Right side as you are facing)

Using a pliers, hold the shaft to keep it from turning and prevent damage to the motor. Using a screwdriver, slide the old ring compression on the b lade shaft toward the motor (away from the fan blades) to loosen.

Remove old blade from the shaft by firmly grasping the motor shaft with a pliers (to prevent from damaging) and pull the blade assembly off.

Reverse the above steps to attach the new blade.
Was this helpful?
Thank you for voting!
During Hurricane Ike, frig. saw several inched of saltwater and sand underneath. AFter cleaning up, I tried to run and only the blower fan worked. It must have been just above the water. The compressor did not kick on. I looked at the lowest elec. connections and saw corrsion on the overload protect
3 of 4 people found this instruction helpful.
  • ken from fulshear, TX
  • Really Easy
  • Less than 15 mins
  • Screw drivers
This was after sitting idle for 9 mos. I simply pulled the part, ordered the same part and installed. Nothing more than a couple of screws and 2 wire connections. It now works great.
Was this helpful?
Thank you for voting!
was not defrosting
3 of 4 people found this instruction helpful.
  • denis from freedom, NH
  • Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
first i removed all the screws inside the freezer compartment took out theback and bottom to get to the evap motor,unpluged the wires and removed the evap motor ,removed the fan from old unit and put it on the new unit them mounted it to the back wall of the fridge,,, and put back top and bottom
Was this helpful?
Thank you for voting!
drain freezing up found cond fan not working
3 of 4 people found this instruction helpful.
  • glenn from la harpe, KS
  • Really Easy
  • Less than 15 mins
Cleaned oh t freezer removed floor. Removed back inside wall removed and replaced fan and put back removed parts


L
Was this helpful?
Thank you for voting!
Old end cap broke.
2 of 2 people found this instruction helpful.
  • Travis from North Quincy, MA
  • Really Easy
  • Less than 15 mins
Put the new end cap on and snapped it into place, took about 5 seconds.
Was this helpful?
Thank you for voting!
The above door End Cap broke.
2 of 2 people found this instruction helpful.
  • John from Northglenn, CO
  • Really Easy
  • Less than 15 mins
The repair just required snapping the new part on to the door shelf and then snapping the shelf in to the door.
Was this helpful?
Thank you for voting!
lights blown out
6 of 14 people found this instruction helpful.
  • Gerald from WINTERVILLE, GA
  • Very Easy
  • Less than 15 mins
replaced lights in refrigirator and freezer
Was this helpful?
Thank you for voting!
Right arm of bottom drawers broken.
2 of 2 people found this instruction helpful.
  • Tammy from ELLISVILLE, MO
  • Very Easy
  • Less than 15 mins
  • Screw drivers
I pulled off the plastic strip that says “ vegetables” on one side “fruit” on the other. That exposed screws on the left and right sides. I unscrewed both sides I did the same to the back support arm put the new arm in and it works great! The man who helped me at part select was so patient and so kind and helping me select the right piece to begin with to make sure I had the right model number. Could’ve had a better experience with the repair company. Tammy Peterson
Was this helpful?
Thank you for voting!
Loud noise coming from freezer. Evaporater fan was still spinning but making loud noise
2 of 2 people found this instruction helpful.
  • Joseph from TRAVERSE CITY, MI
  • Very Easy
  • Less than 15 mins
  • Nutdriver
Removed fan housing from top of freezer, then the two screws holding the rest of it in place. Then two more screw and removed the vertical housing in back of freezer. two more screws and I was able to remove the whole back plate. I unplugged evap motor wire from back of freezer wall and unscrewed motor bracket. once motor was free, I remo ved the blade, unscrewed ground wire and installed new motor. I then plugged wire back in to ensure new motor worked and put everything back. Super Easy!!
Was this helpful?
Thank you for voting!
All Instructions for the 3847
61 - 75 of 214