EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

3847 - Instructions

All Instructions for the 3847
91 - 105 of 214

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
freezer worked but thelower part where the milk and the fruit are was warm checked on your site to get help and you were on the money with telling me it was the thermostat i orderd it and it solved the problem thank you.
2 of 3 people found this instruction helpful.
  • david from torrington, CT
  • Easy
  • 30 - 60 mins
  • Pliers, Screw drivers
i took the backing off with a screwdriver, cut the wires and put the 2 wires on that came with the thermostat. p.s. make sure you pull the power plug before you start.
Was this helpful?
Thank you for voting!
Supports for vegetable baskets broken
2 of 4 people found this instruction helpful.
  • Marian from Chapel Hill, NC
  • Difficult
  • 15 - 30 mins
Installed it by hand with my son and myself. Hard ot figure it out and found another part broken. Did not figure out how the screws went in or what they attached to.
Was this helpful?
Thank you for voting!
water leaking from under dishwasher
1 person found this instruction helpful.
  • Edward from E LONGMEADOW, MA
  • A Bit Difficult
  • 30 - 60 mins
  • Pliers, Socket set, Wrench (Adjustable)
Water was leaking from under the GE dishwasher, but once we pulled it out, had apparently been going on for a little while. Turning the water off to the dishwasher made it stop, so it was happening even when the unit was not running, potentially indicating somewhere early in the path of the water to and into the machine.

Indeed , inspecting the water inlet vale showed a slow leak. Getting the replacement part was fine, and it fit the electrical, water inlet (existing 90-degree water inlet elbow), and water outlet connections just fine - but the original machine screws that held on the original water inlet valve did not work. It took a little research to figure out the new type of screw required, which was apparently a 10/16 Type AB, which seemed to be a less common type of sheet metal screw (with a point), as opposed to the original flat-ended machine screws. So, after ordering those separately (which were a bit expensive), it went together fine.

A note on the water inlet valve part just indicating the the threading on those parts has changed over time, so potentially ordering the screws to attach it might be worthwhile, would be good information to add about the water inlet valve.
Was this helpful?
Thank you for voting!
Had a 'ticking' sound
1 person found this instruction helpful.
  • John from PARKVILLE, MO
  • Easy
  • 30 - 60 mins
  • Socket set
Separately (from a different site) purchased new compressor fan and motor. I purchased the grommets here because the other site listed the grommets as temporarily out of stock. I did watch one of the videos on PartSelect about the grommet replacement. Repair was pretty simple, biggest challenge was getting to the screw on the far side o f the motor. Removed the two screws holding the fan motor into place. Removed motor and blade. Reinstalled with new fan blade, new grommet and new motor.
Was this helpful?
Thank you for voting!
Freezer was cold but fridge was warm. Coils in the back of the freezer were getting frosted. Defrost Sensor was broken
1 person found this instruction helpful.
  • Kevin from Charlotte, NC
  • Easy
  • 30 - 60 mins
  • Socket set
-Empty the freezer
-Take the cover in the back of the freezer off
-Melt the ice off the coils (heat gun, hot water, etc.)
-Cut the wires off the old sensor and connect the new sensor using a soldering iron or some other method.
-Cover the spliced wire with heat shrink, electrical tape or some other method.
-Reasse mble the cover

Done!
Was this helpful?
Thank you for voting!
Evaporator coil freeze up
1 person found this instruction helpful.
  • Michael from BRADENTON, FL
  • Really Easy
  • 30 - 60 mins
  • Nutdriver
Up plug from wall removed rear access cover in freezer let thaw out and replace two wire sensor had previously checked out knowing the defrost strip was good and the defrost thermostat was visually deformed and tested open at freezing and 40 degrees
Was this helpful?
Thank you for voting!
Noisy
1 person found this instruction helpful.
  • Brad from SPRING MILLS, PA
  • Very Difficult
  • More than 2 hours
I didn’t do the repair because I ordered two grommets. When they arrived, one of the packages was empty! Instead of just sending me another one, they refunded the part so I still need one. By the way, I was not refunded half the shipping either which was more than the part itself.
Was this helpful?
Thank you for voting!
Broken light switch
1 person found this instruction helpful.
  • Deborah from BRADLEYVILLE, MO
  • Very Easy
  • Less than 15 mins
  • Pliers, Screw drivers
This was so easy I think it took me 2 minutes. I am not very mechanically inclined but that didn't matter! Works perfect thank you!
Was this helpful?
Thank you for voting!
Defrost Timer went bad.
1 person found this instruction helpful.
  • Phillip from HARRISON, MI
  • Very Easy
  • Less than 15 mins
  • Socket set
I sent back the other one with the print out for FedEx that your company e-mail to me and then i put the new one in, very easy took a few min's
Thank you Mr. Phillip Lewis
Was this helpful?
Thank you for voting!
The light inside the oven had burned out
3 of 7 people found this instruction helpful.
  • Catherine from SEATTLE, WA
  • Very Easy
  • Less than 15 mins
0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap. ... Read more />3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.

No tools needed, the cap is just held in place with pressure from the wire.
Was this helpful?
Thank you for voting!
My light in the refrigerator was going on and off.
1 person found this instruction helpful.
  • Nan from PURCELLVILLE, VA
  • Very Easy
  • Less than 15 mins
I unplugged the refrigerator. Pressed the tab near the light bulb. Unplugged the socket and reconnected it.
Was this helpful?
Thank you for voting!
Fridge light dead even with new bulb
1 person found this instruction helpful.
  • marj from NEWBURY PARK, CA
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
1- youtubed the potential diagnoses, 2- resourced and ordered parts, 3- removed old socket, installed new one :-)... My fridge is an older fridge and could've used a screwdriver for eyeglasses. Plug and play easy... YAY!
Was this helpful?
Thank you for voting!
freezer iceing up
1 person found this instruction helpful.
  • tom from WESLEY CHAPEL, FL
  • Really Easy
  • 15 - 30 mins
  • Nutdriver
removed screws holding back plate removed air devise pul slightly out lift straight up and ou remov 2 screws in the fan cage remove ice maker 2 screws and a plug in connector.pull back fram slowly forward angle to the left remove.you'll see condenser in front of you.thermostat is to the right attached to top coil of condenser clips on rem ove.two wires cut close to old thermos and remove install new one make sure back which is plastic faces you.attach wires with wire nut or inline #14 slices.just go in reverse to finish. maakesure you unplug fridge first and of course plug her back in.wait 24 hours for everything to settle down.
Was this helpful?
Thank you for voting!
Fan was getting really noisy.
1 person found this instruction helpful.
  • frankie from Port Richey, FL
  • Really Easy
  • 15 - 30 mins
  • Nutdriver
Looked at fan and seen it was rubbing metal cage. After looking and checking fan noticed bushings were worn letting fan hit cage. Repair was very easy. Used a 1/4 inch nut driver to remove bracket holding fan. Pulled fan blade off shaft by just pulling it forward. Removed fan and replaced grommets. Reassembled fan and fan blade. Took just 10 minutes.
Was this helpful?
Thank you for voting!
Lights did not work, bulbs were good
1 person found this instruction helpful.
  • Donita from O FALLON, MO
  • Easy
  • Less than 15 mins
  • Screw drivers
Took out the light sockets, plugged in the new ones. I found the manual on line to find the part numbers. Parts select parts were perfect
Was this helpful?
Thank you for voting!
All Instructions for the 3847
91 - 105 of 214