EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

3847 - Instructions

All Instructions for the 3847
1 - 15 of 214

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
No power to the fan and compressor
222 of 302 people found this instruction helpful.
  • Christian from Kearneysville, WV
  • Really Easy
  • Less than 15 mins
  • Screw drivers
I have a fridge in my garage. I have found that a glass of ice water or a cold drink outside is very important to me. When I discovered melting ice dripping onto the garage floor I was very upset. I spun the fridge and found that the compressor and fan weren't starting. I got out my multi-meter and discovered that power was not makin g it to these components. I did some research and found the wiring diagram online. There really isn't too much going on with a fridge and the most likely candidate seemed to be the run capacitor. I ordered the part, replaced it in a few minutes and the fridge began working again.
Was this helpful?
Thank you for voting!
Sticking Light Switch
122 of 178 people found this instruction helpful.
  • Jonathan from Lilburn, GA
  • Really Easy
  • Less than 15 mins
  • Pliers, Screw drivers
I applied some tips learned by reading other reviews. So before I started I grabbed my trusty vise grip pliers and a small screw driver. I locked onto the switch actuator, the part that the refrigerator door pushes in, with the vise grips and pulled on it just hard enough to get the screw driver inserted in the right side to push in the c atch clip so the switch could be pulled out further each time the catch clip was depressed to the next detent. Then I used the screw driver on the left site to encourage the switch past the detents on the left and very quickly the switch was out of the mount. The wires from the refrigerator pulled out with the old switch. I unplugged the old switch from the wires and plugged in the new switch and shoved the new switch back into the mount, wiggled it a couple of times to make sure it was secure and the job was done. Once I applied the vise gripes at first, the whole job took less than a minute.
Was this helpful?
Thank you for voting!
refrigerator was not cooling but the freezer worked fine.
93 of 110 people found this instruction helpful.
  • Wanda from Cabins, WV
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
My husband put on the defrost timer. At first I thought the part was not going to fix the problem. After about 5 hours my refrigerator was still warm. I went to work and when I got home that evening my refrigerator was cooling and down to 28 degrees. So if you replace this part wait at least 12-24 hours. Give it time to stablize. My husband says it has to go through its cycle. It works on a 24 hour timer. My refrigerator is working fine and this has saved me alot of money. My husband says, once you put on the timer you may have to use a flat screwdriver and turn the small dial clockwise one click to start it. He removed the kick grill and replaced the part. Dont forget to shut breaker off to replace this part. Turn power back on and start the timer. We are so happy that we now have a working refrigerator.
Was this helpful?
Thank you for voting!
Freezer & Frig Were Not Cold
77 of 104 people found this instruction helpful.
  • Sam from Cooper City, AL
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
First I removed the rear cover, located at the bottom of the refrigerator. Then I cleaned out the dirt & dust on and around the compressor. The relay has a cover, that is secured with a spring loaded clip. To release the clip, push in with your fingers, while disengaging the end clip with a screwdriver. Once one side is off the ot her lifts off. Remove cove exposing the relay. There is one wire terminated, with a spade clip, remove it. With a strait blade screwdriver, pry the relay off the 2 post it slides on to. (Don't be surprised if it breaks into pieces, as they are sometimes brittle. ) Slide the new relay onto the 2 posts, replace the wire onto the right terminal, and replace the relay cover & clip. Replace the rear cover. Plug in and test.
Was this helpful?
Thank you for voting!
display showed dE
75 of 119 people found this instruction helpful.
  • Nancy from Hamburg, NY
  • Easy
  • Less than 15 mins
  • Nutdriver
popped off front grille, removed 2 screws for bracket, then had to remove one screw for timer. unplugged old timer, reversed procedure, all works.
Was this helpful?
Thank you for voting!
bad light socket
45 of 56 people found this instruction helpful.
  • nancy from silsbee, TX
  • Really Easy
  • Less than 15 mins
unplugged refrigerator. removed light bulb from old socket. unsnapped old light socket and pulled it out just enough to diconnect the electrical plug that plugs into the socket . discarded the old socket and plugged in new socket. snapped in new socket into refrigerator. i watched how to do this simple procedure on you tube and decided to do it myself. easy easy easy
Was this helpful?
Thank you for voting!
Relay
42 of 54 people found this instruction helpful.
  • John H from Austin, TX
  • Really Easy
  • 15 - 30 mins
Removed back panel. Opened cover to relay attached to the compressor and pulled off replacing with new relay. No problem.

Better than paying $250 for someone else to do it.
Was this helpful?
Thank you for voting!
Freezer coils icing up, fridge too warm
33 of 36 people found this instruction helpful.
  • Tim from West Palm Beach, FL
  • Easy
  • 15 - 30 mins
  • Nutdriver
Had to remove inside panels to expose coils in freezer. Used hair dryer and towels to de-ice. Reading online learned about defrost heater (long thin glass tube with wire coil in it I could not see b/c up under the inside of the coils). Who would have guessed freezers have heaters in them!! And learned the defrost timer (inside the fridge) is just a continuous clock turning on and off the defrost heater. Anyways I used a screwdriver to turn the timer to defrost mode and by disconnecting the wires from each end of the heater and measuring the voltage, I found 70 volts there. Hmmm. I didn't know what was the right volt amount.
Reading online I also found out the defrost Thermostat is basically a temp actuated on/off switch for that heater, so that while the timer is sending *120* volts to the heater (which gets red hot by the way) the therm switches the heater off when the temp gets high in the freezer.
I eyeballed the therm ( it looks like a little can) and I saw that it was coming apart. The key at this moment is you can cut out and bypass the therm to see if the heater works. If it does you know the therm is the bad boy. But only do this as a momentary test or the heater will probably set your fridge on fire after a while!

Always remember to unplug the fridge when you are messing with the wires! And dry it up inside before putting your hands and tools in there!

So I ordered a therm using the model # of the fridge. Had to cut the old out and strip / wire nut the new one in.

Took too long b/c I was hung up on the heater being bad (after all it didn't heat up when I put the timer in defrost) and not knowing about the rights volts to the heater.

PartSelect helped out great! Thanks!
Was this helpful?
Thank you for voting!
Light switch inside refrigerator wasn't working
31 of 43 people found this instruction helpful.
  • Erick from Elmhurst, NY
  • Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
First turned off power and removed top shelf.
Then I used a flathead to slowly pry the switch out by the two sides. You just anlge ita bit and it slideds out easily. Then I disconnected the wires from the old switch, connected the new one and installed the new switch by snapping it back into the cutout.
Was this helpful?
Thank you for voting!
Noisy Evap Fan Motor
27 of 33 people found this instruction helpful.
  • Vera from Alexandria, VA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Could not haven been easier. Simply unplug fridge, remove air duct mounted on rear panel, release panel itself, pull fan blade off, disconnect grounding wire, detach fan motor bracket, disconnect wire harness to release fan motor, install new fan motor and reconnect, secure with bracket, reconnect grounding wire, reposition fan blade onto motor shaft, reinstall rear panel and secure screws. Remount air duct and plug appliance back in. VOILA. All done in less than 15 minutes!!!
Was this helpful?
Thank you for voting!
My fridge and freezer were not getting cold enough.
23 of 24 people found this instruction helpful.
  • Marcus from SLC, UT
  • Really Easy
  • 15 - 30 mins
  • Nutdriver
The Fridge and freezer were not very cold except for in the very back of the freezer (where the coils are). So I opened up the back of the freezer by first removing the dome light cover and removing all the visible screws. I then lifted up and pulled out the vent in the center of the back panel and removed the two remaining screws on the back panel. At that point I removed the back panel exposing the coils and fan. I saw that the fan was not spinning so I used a screw driver to manually turn the defrost timer found on the top of the inside of the fridge. Once I had turned the defrost timer once complete rotation, and the fan didn't turn on, I was pretty sure that it was the fan. I still wasn't sure that the fan was the only problem, but I couldnt see anything else that wasn't working properly. I decided to take a chance and order the fan motor (not the entire assembly. it is easy to replace the moter only leaving the original fan blades and housing). Once I got the part, I unplugged the old fan motor, put in the new fan motor, and pugged it in and it started spinning right away. I put everything back together the same way I took it apart and it has worked great ever since.
Was this helpful?
Thank you for voting!
refrigerator would not defrost
21 of 23 people found this instruction helpful.
  • Donald from worthington, OH
  • A Bit Difficult
  • 15 - 30 mins
  • Screw drivers
Look were timer was located, in my refigerator is next to the dial to ajust the temperature. used a screwdriver to get panel off. replaced timer then used a straight screwdriver to advance timer to turn on compessor . monitor temperature . checked out.
Was this helpful?
Thank you for voting!
it quit working-refer-freezer-part,fan keeped running
21 of 25 people found this instruction helpful.
  • jim from buckeye, AZ
  • Really Easy
  • Less than 15 mins
  • Nutdriver
pulled out switchs verified part #'s-ordered replacements- its actually plug in switches and very simple
Was this helpful?
Thank you for voting!
This refrigerator had pawer( lite was on) but nothing turning--motor or fan. Turned control temperature min-max - no cange.
49 of 112 people found this instruction helpful.
  • HAE-YOUNG from Douglaston, NY
  • Easy
  • 1- 2 hours
  • Screw drivers
Found burned Defrost timer contacts.
Was this helpful?
Thank you for voting!
The refrigirator light would not come on.
26 of 44 people found this instruction helpful.
  • Jania from Novato, CA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Poped out with screwdriver the old swithch and unplugged the two wires. Plugged in the wires to the new swithch and pushed it back in the hole where the old switch was before.
Was this helpful?
Thank you for voting!
All Instructions for the 3847
1 - 15 of 214