EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

3847 - Instructions

All Instructions for the 3847
46 - 60 of 214

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Refrigerator to warm
5 of 5 people found this instruction helpful.
  • Lloyd from PITTSBURG, CA
  • Easy
  • 15 - 30 mins
  • Screw drivers
Instructions say run capacitor is by motor, but on this frige its in the refrigerator compartment. The capacitors looks different, one square and the other long
Was this helpful?
Thank you for voting!
Door gasket was cracked and coming off
5 of 5 people found this instruction helpful.
  • Mark from SALISBURY, MD
  • Really Easy
  • 15 - 30 mins
  • Socket set
Took freezer door off with torque screwdriver, unscrewed freezer door/refrigerator hinge with 3/8 socket. Removed refrigerator door and put on kitchen table. (Turn refrigerator off temporarily). Put freezer door back on temporarily. Pull out old gasket from groove on door. Put in new gasket. Take freezer door back off, put on refrigerator door, hinge, freezer door, put torque screws back in, your done. (Turn fridge back on)
Was this helpful?
Thank you for voting!
The old plastic slide broke from hanging too much weight on it.
5 of 6 people found this instruction helpful.
  • Terrence M from Portsmouth, NH
  • Really Easy
  • 15 - 30 mins
First I had to go to the hardware store to buy a star bit to remove the old screws ($1.09). I attached it to my quarter-inch drill and used it to remove the old screws. I then used those same screws to attach the new slide. Once I had the star bit, it was little more than a five-minute task.
Was this helpful?
Thank you for voting!
A rat had chewed half of all four blades off
9 of 18 people found this instruction helpful.
  • Curtis from Dothan, AL
  • Really Easy
  • Less than 15 mins
  • Nutdriver
First I removed the left condensor fan motor bracket nut, loosened the right motor bracket, dropped the moter bracket down freeing the motor from the rubber grommets.
Pulled the fan off from the motor shaft, pressed the new fan on the shaft and installed new grommets. Replaced the motor bracket and tightened the right bracket nut an d checked fan for clearance and free spin. Reinstaled the left bracket nut. Turned on the refrigerator and checked fan for action. Everything worked great.
I did not know the fan replacement came with a compression ring already installed, so now I have an extra compression ring.
Was this helpful?
Thank you for voting!
freezer cold but refrigerator warm, would not cycle the defrost on freezer
4 of 4 people found this instruction helpful.
  • MATT from OAKLAND, MI
  • Really Easy
  • Less than 15 mins
  • Screw drivers
two screws and a connector were removed to replace the timer.
Timer was located on the top front of fridge
Was this helpful?
Thank you for voting!
Bad defrost timer
5 of 7 people found this instruction helpful.
  • Bruce from Silver Spring, MD
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Parts Select made this an effortless process. From finding the part, ordering, to the online diagrams.

I'll be back...
Was this helpful?
Thank you for voting!
Broken part need to be replaced
4 of 4 people found this instruction helpful.
  • ANGELINE from STAMFORD, CT
  • Really Easy
  • 30 - 60 mins
I didn't call for repair iwas just order 2 pcs it's coming early morning in the next day I was happy 1hundred% I will recommend this company
Was this helpful?
Thank you for voting!
The lights were on inside however the the water/ice dispenser did not work and the fridge and freezer side was not cooling
5 of 7 people found this instruction helpful.
  • Rickey from DUMAS, AR
  • Really Easy
  • 30 - 60 mins
  • Socket set
Simply take off the back panel. Remove the old run capacitor which is attached to the compressor by a white part. It pulls right off. You will have to unplug two wires. I took a pic to ensure I plugged the wires back up the correct way. Then I attached the new capacitor to the white part and put on the sleeve that was included, plugge d it back into the compressor and zip tied the excess part of the sleeve. Once done plug fridge back up (always unplug electric devices when doing maintenance) to check before replacing back panel. It may take a few minutes before it kicks on.
Was this helpful?
Thank you for voting!
Right side shelf bracket broken, shelf wont stay up. 1 bin cracked.
4 of 5 people found this instruction helpful.
  • Carole from RIDGECREST, CA
  • Really Easy
  • 30 - 60 mins
  • Screw drivers
Removed glass shelf, cleaned and set aside. 2 screws attach the old bracket, one on front, one in rear. Removing front screw requires popping off cover on front of shelf. (gently) Scrub off accumulated gunk. Install new bracket reusing same screws. Place shelf in fridge, making sure bin divider is attached to shelf with open end to front so that bins can slide into place. Slide glass shelf top back in place, do this gently, does NOT require force. Pop front shelf cover back on. Gently slide in bins. Done.
Was this helpful?
Thank you for voting!
Difficulty in removing the old switch
5 of 8 people found this instruction helpful.
  • James from Federal Way, AL
  • A Bit Difficult
  • 30 - 60 mins
  • Screw drivers, Socket set
The old switch was hard to remove. Thinking that I may have to loosen the wires I used a socket wrench to remove a clamp. This was unnecessary. In the end the switch did come out using a large size screwdriver. The problem was that the expanding plastic tongue is not visible from the ouside so you have to try to feel your way around. If i had ordered the replacement before and not afterwards I would have seen this before hand.
Was this helpful?
Thank you for voting!
refrigerator compartment too warm
4 of 5 people found this instruction helpful.
  • samuel from windsor mill, MD
  • Easy
  • 15 - 30 mins
  • Nutdriver
Unplugged fridge and removed back panel inside freezer compartment . Unclipped defrost thermostat and snipped off with wire cutters . Installed new defrost thermostat with wire nuts , clipped back on , re-installed back panel , turned on fridge and within a couple hours food compartment began cooling down . Thermostat looks like a small m etal can clipped onto the heating coils with 2 wires attached . Also noticed excess ice build up on coils melted and drained into pan under fridge once unit started working .
Was this helpful?
Thank you for voting!
Fridge doesn't cool properly; freezer iced up
4 of 5 people found this instruction helpful.
  • Will from Houston, TX
  • Easy
  • 15 - 30 mins
  • Nutdriver
You will need a 1/4" nut driver or socket & extension.
Remove the back panel of the freezer compartment.
Pull of the wires, remove the fan assembly and replace the fan motor.
Was this helpful?
Thank you for voting!
Refrigerator light wouldn't come on.
4 of 5 people found this instruction helpful.
  • Daniel from Crown Point, IN
  • Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
After replacing the light bulb and still no light I manually pushed the light switch button. Intermittently the light would come on then go out. I removed the power plug from the power source then replaced the light switch. I plugged the refrigerator back in and now I open the door the light comes on and stays on until the door is closed.
Was this helpful?
Thank you for voting!
Ordered replacement shelf
4 of 5 people found this instruction helpful.
  • Dennis from Malboro, MA
  • Easy
  • Less than 15 mins
I mistakenly ordered the incorrect shelf width when trying to figure out what I needed from a similar model. I called to get assistance and the correct part was found right away. If you think there is something in question on the part you are ordering it is worth calling. The agent was very knowledgible was able to utilze additional in fo she had to find what I needed the first time. The return on the incorrect part went very well also.

Thanks for my new freezer compartment shelf!!
Was this helpful?
Thank you for voting!
Old timer quit working.
7 of 14 people found this instruction helpful.
  • John from Mesa, AZ
  • Easy
  • Less than 15 mins
  • Nutdriver, Screw drivers
Installed the new timer.
Was this helpful?
Thank you for voting!
All Instructions for the 3847
46 - 60 of 214