EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

3847 - Instructions

All Instructions for the 3847
31 - 45 of 214

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Overload switch failed on compressor. No cooling
8 of 9 people found this instruction helpful.
  • phillip from hartselle, AL
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Unplug. Remove back cover. Remove retainer (simple wire clip) from overload. Unplug overload from compressor. Remove two power wires (if stabs are tight you might need pliers). Note which wire goes where. Remove capacitor from overload (just pul it straight out .. Pull hard or pry a little with screwdriver. Insert capacitor into new switc h. Reattach wires to same place in switch. Insert switch into compressor. Replace retainer clip. Replace rear cover with original screws. Plug in. Cool!
Was this helpful?
Thank you for voting!
Ice in freezer running down sides
8 of 9 people found this instruction helpful.
  • P. Michael from Tustin, CA
  • Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
This is a built-in unit. Remove the external bezel at the top of the unit. Reach through the unit and unplug the frig. On the compressor unit, you'll see a vertical metal panel. Remove the metal panel and the timer is right behind it. Remove one wire at a time and switch it to the new timer. Remove timer and replace with new one. ... Read more />
Just an added comment, GE Service wanted to put an "ice kit" into my unit. The full repairs would have cost $1,000. While I described how to replace the defrost timer, the problem was the tray heater. But that's another story.
Was this helpful?
Thank you for voting!
defrost system kept freezing up
8 of 10 people found this instruction helpful.
  • Robert from Williamstown, NY
  • Easy
  • 15 - 30 mins
  • Screw drivers
took out 4 screws - lowered timer cover - replaced timer- put it back together
Was this helpful?
Thank you for voting!
Poor cooling, running all the time
12 of 22 people found this instruction helpful.
  • MICHAEL from ALEXANDRIA, VA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Removed two screws holding the cover. Unclipped and unplugged the defroster timer. Plugged in the new one . Replaced the cover. Finished.
Was this helpful?
Thank you for voting!
Freezer stopped working
9 of 13 people found this instruction helpful.
  • Clifford from Melbourne, FL
  • A Bit Difficult
  • More than 2 hours
  • Nutdriver, Pliers, Screw drivers
I noticed that if I unplugged the refrigerator and plugged it back in a while later it would start working but eventually would stop. I deduced the problem was likely the defrost thermostat. I ordered the thermostat but it was in a difficult place behind the evaporator coil which I could not remove. While I was trying to work it into posi tion my hand pressed against the defrost coil and shattered the glass sheath. I ordered the coil and finally managed to get it and the thermostat installed. The refrigerator seems to work fine now.
Was this helpful?
Thank you for voting!
Freezer not getting cold enough to freeze ice cream
8 of 10 people found this instruction helpful.
  • Gary from ROSETO, PA
  • A Bit Difficult
  • 30 - 60 mins
  • Screw drivers
I took the advice off of your website about the only thing that will fix
the problem is change the run capacitor. I felt assured that I would
have a working refrigerator freezer after making this change. I was
pretty disheartened when it didn`t solve anything. I was not going to
take the new part back out after the sma ll challenge of putting it in.
The next day I found out how to test the old capacitor and it was still
good. I will just have to eat the $49. I did learn not to take advice from
a website even if it seems like a sure thing
Was this helpful?
Thank you for voting!
Refridgerator wouldn't cycle into defrost mode without doing it manually.
9 of 14 people found this instruction helpful.
  • Ben from Warrior, AL
  • Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
I removed the shield over the timer and the part that supported the timer. Just unpluged it and pluged in new timer and put back shield. I had already replaced the defrost heaters which had totally burned up. I also replaced the thermostat while I was making the repairs although the old one was still o.k. All the information that I needed to make the repairs I obtained through your website. After looking at several websites to compare prices-etc, I found yours to be the best overall. Thanks-a-million your website is worth it's weight in Cold Food !
Was this helpful?
Thank you for voting!
Noisy fan in freezer compartment
6 of 6 people found this instruction helpful.
  • Jeffrey B from Lewiston, ME
  • Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
Removed shelf by pushing to left and lifting up on RH end. Removed screws in plastic cooling tower and slid tower up. Pulled back wall of freezer compartment out, RH side first. Removed two screws from fan bracket, unplugged fan wiring harness by compressing connector spring clips and pulling joint apart. Pulled fan blade off (note locati on of blade on shaft for reinstall alignment purposes), removed both green grommets.Then just reinstalled new items.My philosphy on repairs of this nature is to replace all related parts that could be contributing to problem. The parts are cheap compared to the aggravation and inconvenience of doing the repair several times until you fix the problem. You don't need to purchase the compression ring if you buy the fan blade as it has one already installed on it. Problem solved, though now that the noise is gone am hearing fainter similar noises from lower fan. Should I be surprised, both fans are of similar design.
Was this helpful?
Thank you for voting!
refrigerator wasn't cooling but the freezer was working properly
6 of 6 people found this instruction helpful.
  • Don from BELLVILLE, TX
  • Very Easy
  • 15 - 30 mins
  • Nutdriver
From instructions found on the site I was directed to the defrost timer part being bad. And from the information others posted that have had the same problem I was able to replace that part by removing the bottom grill just below the door and on the left side was the part. Removing one screw to remove the bracket from the frame and then another screw to remove the part from the bracket. I found it easier to remove the part from the bracket before I pulled the part out so I would have more room to unplug the connector. Just reverse the steps to replace the new part. It took about a day or so for the refrigerator to get to the proper temp.
Was this helpful?
Thank you for voting!
compressor not starting
9 of 15 people found this instruction helpful.
  • H.K. from Seagoville, TX
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Refrigerator is not cooling. Light and fan working. Changed the capacitor.. Still not cooling. Back to discovery mode.It may be the timer
Certainly not PartSelect's fault. They have great service.
Was this helpful?
Thank you for voting!
no problem
7 of 10 people found this instruction helpful.
  • hung from herndon, VA
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
The part i received fit perfect, i just removed the old part and put the new part in with the screw driver.Really easy
Was this helpful?
Thank you for voting!
Bar end cap broke
6 of 7 people found this instruction helpful.
  • Bushnell from Gulf Shores, AL
  • Really Easy
  • Less than 15 mins
Easy fix - snapped together.
Was this helpful?
Thank you for voting!
Fan was making annoying noise and rubbing against the frame of opening.
6 of 8 people found this instruction helpful.
  • Tony from Los Angeles, CA
  • Really Easy
  • Less than 15 mins
  • Nutdriver, Screw drivers, Socket set
Removed old fan and replaced the fan with new one.
2 years ago, the refrigerator was under warranty and tech replaced the fan but I found that the fan was not the original spec fan. Apparently, the fan that the tech replaced did not fit opening.

Now, my refrigerator works no problem. Save a ton of $$$ by doing it myself. Do not have to buy a new fridge and this one works perfect.
Was this helpful?
Thank you for voting!
Plastic frame was broken
5 of 5 people found this instruction helpful.
  • Sandra from YUMA, AZ
  • Very Easy
  • Less than 15 mins
I removed the broken frame, glass, and bins from the refrigerator, cleaned the area, put the new frame in place making sure it was fitted into the brackets securely, and replaced the glass and bins into their proper slots.
Was this helpful?
Thank you for voting!
light not working
7 of 11 people found this instruction helpful.
  • robert from FRANKLIN SQ, NY
  • Very Easy
  • Less than 15 mins
  • Pliers, Screw drivers
I used pliers to pull lightly on the head of the switch, while I inserted a small flat head screw driver into the base of switch and gently worked around the edges to free it from the panel.
Was this helpful?
Thank you for voting!
All Instructions for the 3847
31 - 45 of 214