EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

3847 - Instructions

All Instructions for the 3847
106 - 120 of 214

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Light would stay on when door closed
3 of 7 people found this instruction helpful.
  • James from Glendale Heights, IL
  • Really Easy
  • Less than 15 mins
  • Nutdriver, Pliers
Extremely easy repair, the hardest part was getting the old switch out. I used a pair of needle nose pliers to squeeze the tabs in and it came right out.
Was this helpful?
Thank you for voting!
light switch freezer door
3 of 7 people found this instruction helpful.
  • Sumlorq from Cleveland, OH
  • Really Easy
  • Less than 15 mins
put the gratefruit knife behind the old switch pooped it out pluged the new one in piece of cake 5min.even vacumed the dust off the coil
Was this helpful?
Thank you for voting!
My freezer door had a retainer bar that became disconnected at one end because the coupling broke.
1 person found this instruction helpful.
  • Robert from SAN DIEGO, CA
  • Really Easy
  • Less than 15 mins
I slipped the coupling over the bar and then into a door slot. It was very easy.
Was this helpful?
Thank you for voting!
Light Switch Not Working - Needed New Switch
1 person found this instruction helpful.
  • Joe from SUGAR LAND, TX
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Remove the top cover above the door by lifting it slightly and pulling forward. I used a mirror to make sure that there was nothing in the way of accessing the switch from above. I used a blade screwdriver to press against the switch retainer on the topside, while GENTLY prying from below with another blade screwdriver to get the switch d islodged. Once the retainer was past the opening, I wiggled the switch downward and then rotated it to the left when the rounded top right edge of the switch was visible. This allowed the wiring to the connector to pass thru the hole. I pushed the wiring from the top and pulled from below to get the connector below the opening for the switch. I then unplugged the switch, plugged in the new switch and reversed the removal process feeding the connector thru first then rotating the switch to the right to get the rounded edge of the switch thru the opening, then pressed the switch up into the opening until it snapped into place. Total time less than 10 minutes.
Was this helpful?
Thank you for voting!
40 year old refrigerator brittle light switch fell apart
1 person found this instruction helpful.
  • Loren from EL PASO, TX
  • Really Easy
  • Less than 15 mins
  • Pliers, Screw drivers
with a jewelry screwdriver I pried the lock tab in and pulled switch down carefully, the hardest part was that the power wire connector was stuck on good but the pliers and the jewelry screwdriver was its match for a bout 5 minute for one connection a simple pull off prong connection. After the wire connected back to switch it popped back in SNAPP
Was this helpful?
Thank you for voting!
Light went out in refrigerator
1 person found this instruction helpful.
  • Gary from EAST JORDAN, MI
  • Really Easy
  • Less than 15 mins
  • Pliers, Screw drivers
Pop out switch, pull wires, attach wires to new switch and pop back in. Easy smeasy!
Was this helpful?
Thank you for voting!
Was not allowing defrost heater to work
1 person found this instruction helpful.
  • Ronnie from MARION, LA
  • Really Easy
  • Less than 15 mins
  • Nutdriver, Pliers, Screw drivers
Unplugged refrigerator Removed the cover in freezer compartment
Removed old thermostat and installed new
Replaced cover and plugged in refrigerator
Was this helpful?
Thank you for voting!
bulb out
1 person found this instruction helpful.
  • Kenneth from Rowe, VA
  • Really Easy
  • Less than 15 mins
I ordered the part, within two days we had received it. My husband put the part in and I really don't know what he used doing so. All I know is that the light works now and we don't have to use the flashlight. Thanks a lot.
Was this helpful?
Thank you for voting!
broken door shelf bar holder
1 of 2 people found this instruction helpful.
  • Stan from Dallas, TX
  • Really Easy
  • Less than 15 mins
I ordered the part before noon and I they had it out the door and in my hands within 24 hours! It took about 2 minutes to take out the broken part and snap in the new one!Great service and easy install!
Was this helpful?
Thank you for voting!
Light was flicking
1 of 2 people found this instruction helpful.
  • Stephanie from KEARNY, NJ
  • Really Easy
  • Less than 15 mins
  • Screw drivers
It was way to ez to install only a couple of minutes that's it
Was this helpful?
Thank you for voting!
Broken light switch
1 of 2 people found this instruction helpful.
  • Ted from SANDWICH, IL
  • Easy
  • 15 - 30 mins
  • Screw drivers
took a little more effort than the video show to remove old module and replace new. Works fine now.
Was this helpful?
Thank you for voting!
Short in the light socket.
1 of 2 people found this instruction helpful.
  • ED from ENON, OH
  • Very Easy
  • Less than 15 mins
Un Plugged the frig. Unlocked the socket by pressing down on the latch. Pulled the socket out ensuring I had enough slack. Unplugged the old socket installed the new. Plugged the frig back in. Tested the switch . Very easy-to-use.
Was this helpful?
Thank you for voting!
The control board generated clicking noise. Temperature display wrong values.
1 of 2 people found this instruction helpful.
  • QUOC-LOC from LYNN HAVEN, FL
  • Really Easy
  • 30 - 60 mins
  • Screw drivers
On the internet forum I read that if the control board needs to be changed , do the same for the Run Capacitor/relay.
The Ge profile refrigerator was 15 years old. First I disconnect the power cord,
I removed the control board at the back of the fridge, replaced it with a new one and did the same for the run capacitor.
P lugged the power cord back and it works fine. GE repair service did not want to come to do it. DIY is fine.
Was this helpful?
Thank you for voting!
Change bulb
3 of 8 people found this instruction helpful.
  • Louis from LEAGUE CITY, TX
  • Really Easy
  • 30 - 60 mins
  • Nutdriver
Easy
Was this helpful?
Thank you for voting!
The door activated light switch was missing.
1 of 3 people found this instruction helpful.
  • Don from Eugene, OR
  • Really Easy
  • Less than 15 mins
Pulled the two wires out from the access hole in the lower part of the refrigerator. Put them in the spade connectors on the new switch, and pushed the switch into place.
Was this helpful?
Thank you for voting!
All Instructions for the 3847
106 - 120 of 214