Hotpoint Refrigerator Hardware

Hotpoint Appliance Parts
Shop By Part Type

Popular Hotpoint Refrigerator Hardware

Your Price
$6.24
  In Stock
Evaporator Fan Grommet - Red
★★★★★
★★★★★
(18)
PartSelect Number PS963756
Manufacturer Part Number WR02X12008
If you notice that your refrigerator or freezer is noisy or too warm, you may need to replace the evaporator fan grommet. This part is red in color, and is about 1 inch in diameter. The evaporator fan grommet is located behind the evaporator fan cover in the back of the freezer. You will need to remove the evaporator fan cover to access the evaporator fan and complete this repair. Before you begin this repair, ensure the power to the refrigerator is disconnected. You will need a pair of needle nose pliers, a small flat blade screw driver and both a 1/4 and 5/16-inch nut driver to complete this repair.
Fixes these symptoms
  • Clicking sound
  • Freezer section too warm
  • Fridge too warm
  • See more...
Installation Instructions
alex from rohnert park, CA
evaporator fan making lots of noise
the repair was really easy!!! took longer to put the little clip on the fan part than it was to install the whole moter and put everthing back together

save money do it yourself.....
Read more...
Your Price
$6.25
  In Stock
Evaporator/Condensor Fan Grommet
★★★★★
★★★★★
(10)
PartSelect Number PS284555
Manufacturer Part Number WR02X10098
This evaporator fan motor grommet, or condenser fan grommet is built for refrigerators. It provides a cushion between the fan motor and the motor mounting bracket. It is made or round, black plastic and is approximately one inch in diameter. If your grommet is torn or damaged and you are getting noise from the fan motor, you may need to replace it. This is an OEM part sourced directly from the manufacturer.
Fixes these symptoms
  • Freezer section too warm
  • Fridge too warm
  • Noisy
  • See more...
Installation Instructions
Joel from Childress, TX
Condensor fan out of service
The only part that I should had used was the condensor fan motor,which it was so easy to remove,and instaled the new one,then replaced the missing parts and problem solved. The technician before me,declare the unit a total loss,there for after doing that, he took the rest of the parts with him for his own benefit. The repair was with no difficulty,and time spend around 20 min. Thanks.PartSelect,your delivery and easy way to place an order is great. Thanks. Joel Read more...
Your Price
$6.24
  In Stock
Compression Ring
★★★★★
★★★★★
(2)
PartSelect Number PS1015726
Manufacturer Part Number WR02X12149
This compression ring is meant to hold the evaporator fan motor in place in the freezer compartment of your refrigerator. This is is a genuine OEM part. The tools needed to complete this repair are a Phillips screw driver and small flat blade screw driver. Be sure to turn off your refrigerator before removing the evaporator fan cover so the fan does not turn on during repair. It is recommended to check the grommets, evaporator fan, and fan blades during repair in case they also need replacning. The compression ring may need replacing if the fan is noisy, or the refrigerator compartments are too warm. This part is sold individually.
Fixes these symptoms
  • Freezer section too warm
  • Fridge too warm
  • Noisy
  • See more...
Installation Instructions
Jeffrey from Tampa, FL
My refrigerator began to overheat and the everything was thawing!!
My refrigerator began to overheat and the everything was thawing!! The condenser fan motor had seized and I thought this is something even I can replace.

I did a Google search on the refrigerator model number. The link to your site looked promising and I clicked on it. I was taken to your web page for my refrigerator and I clicked on the schematic for the condenser assembly.

The schematic had the parts I needed labeled clearly so this layman could be sure to get the right ones.

I ordered the parts at 12:45PM Monday and selected overnight shipping. The parts arrived at 8:35AM Tuesday (Thank you FedEx). I installed the parts and my refrigerator is up and running again.

To get to the condenser fan motor I took off the back panel on the fridge that covers the condenser, fan and coil. The fan/motor assembly is attached to a bracket I removed with two screws. Pulled the bracket assembly out of the back of the fridge, removed the fan blade and then the motor, and put the new motor on the bracket and stuck the new fan blade on the motor spindle. The trickiest part was getting the complete assembly back in. Just went slowly and took my time. Reconnected the wires, no problems. I took pictures of everything that I disassembled BEFORE I disassembled it in case I wasn't sure how something went back in but this job was so simple I didn't need the pictures.

I’m not sure how I could improve on this except maybe you could ship a refrigerator technician, too, to do the install.

Thank you PartSelect everything worked out better than I could have hoped and I saved $220.00 compared to what a repair service was quoting.
Read more...
Your Price
$6.24
  In Stock
SCR 10-16 AB TRP 3/4 NBS
PartSelect Number PS10056090
Manufacturer Part Number WR01X21151
Your Price
$6.24
  In Stock
Lid Bumper
★★★★★
★★★★★
(1)
PartSelect Number PS284979
Manufacturer Part Number WR02X10540
The lid bumper or evaporator fan motor bumper in your refrigerator prevents the fan motor from scraping against the side bracket. If your refrigerator/freezer is noisy, the bumper could be worn down or missing, and the sound could be a result of the motor scraping the side bracket. You will find it between the fan motor and the side bracket on the evaporator fan motor assembly. To access the bumper, you will need to remove the evaporator fan motor assembly from the freezer. This part is made of orange rubber and is less than half an inch in diameter. It has a rounded top and a slightly pointed bottom, and is sold individually.
Fixes these symptoms
Installation Instructions
Darren from Renton, WA
Loud high pitch whining noise behind freezer
Ref. still worked but had this loud high pitch whining noise coming from inside freezer for a few months. It's probably a bad bearing or motor.

1) Remove all shelves and ice dispencer
2) Remove (x2 screws / a green wire that's clipped on) and the evap cover
3) Remove (x3 screws) cover motor/solenoid and unplug harness
3) Remove (x2 screws) icemaker and unplug harness
4) Remove/Loosen (x2 screws bottom / x2 screws top) Duct air freezer
5) Remove (x2 screws) Orifice evap fan and unplug harness
note: will need to remove right screw to get green ground wire off. And be careful on to damage the gasket.
6) Once Orifice out of refrig, disassemble.
7) Main thing to replace is the Motor DC Evap fan, and maybe CapDust, BumperLid, GrommetEvpFan.
8) now just go in reverse order...
That's it . . . wasn't too hard and NO MORE whining!!! Save at least a couple of hundred by not having a prof. come out and do it. Easy enough for most DIY person.
Read more...
Your Price
$6.24
  In Stock
Screw - 8-18 DG TRT20 5/8 S
★★★★★
★★★★★
(1)
PartSelect Number PS1483097
Manufacturer Part Number WR01X10621
This genuine OEM screw is designed for use in refrigerators. It measures approximately ¾ of an inch in length.
Your Price
$7.28
  In Stock
Screw
★★★★★
★★★★★
(1)
PartSelect Number PS1020128
Manufacturer Part Number WR01X10590
This refrigerator door handle mounting screw connects your refrigerator door to the handle. The part is less than 1 inch in length, and can come in both silver and gold colors. When installing this screw, make sure to avoid cross-threading and use reasonable torque to avoid damage to components. This part is an OEM part sourced directly from the manufacturer. This part is sold individually.
Installation Instructions
Carla from BERKELEY, CA
Handles on fridge were discoloured and looked very bad
Actually - we followed the instructions in a video provided by :parts select" when we ordered the parts [the 2 fridge door handles]. It was easy to order with the model number, easy to remove the old handles & easy to install the new ones with the instructions on your web site, and everything arrived timely & reasonably priced. Thanks a heap! Read more...
Your Price
$6.24
  In Stock
Push On Nut
★★★★★
★★★★★
(5)
PartSelect Number PS298353
Manufacturer Part Number WR2X7054
This push on nut is for your dishwasher or refrigerator. As the name suggests, it pushes into place, rather than being screwed in. It is approximately half an inch in diameter and is made of stainless steel.
Installation Instructions
Joseph from Livermore, CA
Water leak from gate (diverter) valve shaft
This was a fairly simple repair. After disconnecting power to the dishwasher and removing the panel below the door, first had to remove a retainer C clip from the gate valve shaft. Then disconnected the linkage from the gate valve solenoid, removed two return springs and slid the gate valve contol arm off the shaft. Then removed the solenoid bracket that was fastened to the housing by 2 screws. This allowed access to the push on nut on the valve shaft. Removed the old push on nut which exposed the leaking seal. Removed the bad seal, then moistened and carefully slid on and seated the new drain valve shaft seal. Affixed new push on nut. Reinstalled the above mentioned parts that were removed. Problem solved - no more leak. Total cost $18.81 for factory GE parts plus $6.95 shipping. Thank you PartSelect. Read more...
Your Price
$6.24
  In Stock
Set Screw
★★★★★
★★★★★
(3)
PartSelect Number PS963200
Manufacturer Part Number WR01X10450
This is a replacement set screw for your refrigerator door. The set screw attaches the door handle to the stud on the refrigerator door. The screw is approximately ¼ of an inch in length and unlike some other screws, it does not have a screw head. It is made of stainless steel and is sold individually. This is an OEM part sourced directly from the manufacturer.
Installation Instructions
Deanna from MANDAN, ND
Fridge handle missing set screw.
Opened the package. Set screw fell on floor. Luckily cat found it right away. Fight the cat for the screw. Dug through my tools and the first Allen wrench I picked up fit. "What the hell? That never happens so obviously the screw won't fit," I think to myself. Put the screw in the hole and give it a few turns until my fat finger can't hold it. It's a miracle and the thing fits! Fight the close quarters with the Allen wrench to tighten it. Works like a charm!! Now I don't scare myself when I open the door thinking I'm going to rip the handle right off. Now I have easy access to my ice cream. The parts finder tool on the website was really easy and I found what I was looking for. Read more...
Your Price
$6.24
  In Stock
Screw
★★★★★
★★★★★
(1)
PartSelect Number PS271689
Manufacturer Part Number WH2X930
This screw is sold individually.
Installation Instructions
Mikhail from Framingham, MA
8 screws and done
After taking off:
5 screws off the back
2 in the front - Husky screws in the front
panel clips - the top panel was opened.

1 more screw for starter switch

DONE - under 15 minutes.
Read more...

Related Parts